"All our motors have a square frame with a compact and robust construction. A modular design allows a wide flexibility of assembly forms. The motors have a laminated housing, which allows high currents in transit. An insulation system with a higher class than F guarantees a longer life of the motors. They are suitable for a wide range of applications. The motors comply with the international requirements 34-1. The following conditions apply: continuous duty S1 and a DC power supply fully controlled by the drive. Features: - Depending on the application, the motors can be equipped with IC0666 air exchanger or ICW81 air water exchanger. - Predisposition for encoder or tachometric dynamo mounting 20 or 40 or 60V/1000T - On request, the motors can be built to measure to go in place of the existing motors - IP23 protection - Heating class F - In 12-24-48-220-440V - Cast iron - Up to 800kW - B3/ B35/ B5 - Insulation class H - Cooling IC06 - 100 - 355 size"
Belgium
"We also offer used engines directly from our stock. These motors are a fast and efficient solution which allows us to help you out by offering short delays for sale or rent with or without purchase option and this at an extremely interesting price. These motors with cages, rings or direct current are revised and tested in our workshops to ensure you an optimal service. They are delivered with a 12 months warranty. Our stock offers used motors with power ranging from 15kW to 5MW. Characteristics: - From 15kW to 5MW - With or without purchase option - 12 months warranty"
Request for a quoteBelgium
"IP23 ventilated open motors (ODP) are an ideal solution for our customers who want compact and smaller motors than IP55 motors. In general, these motors have one less frame size. They are mainly used in clean environments (e.g. manufacturing of plastic bottles for soft drinks, cold compressors for food freezing, ...) STANDARD OPEN VENTILATED MOTORS (OUR CODE: MOV) - Three-phase motors with cast iron housing - IP23 protection - Insulation class F - Heating class B - Legs molded in the casing - Stored in 230/400V - 400/690V - Operating in 50/60hz - Cooling IC01 - Other special voltages or insulation class H on request - Stored speed : 3000 rpm or 1500 rpm or 1000 rpm - Efficiency IE3/IE4 (tomorrow IE5) - Form B3-B5-V1-B35-V15 - Standard motors equipped with PTC sensors for all motors - Motors are equipped with an isolated bearing for use with a variable speed drive. The PI will eliminate circulating currents in the rotor. - Provided with two ball bearings
Request for a quoteBelgium
"The world is changing and companies are under increasing pressure from environmental policies. An international standard was established in 2008 and updated in 2014 to classify the international energy efficiency (IE) of low-voltage three-phase induction motors. This is the IEC/EN 60034-30.1 standard. It reinforces the balance of international efficiency regulations. At Focquet, we have more and more IE4 motors to meet the needs of our environmentally conscious customers. We continue to invest heavily in this type of motor. OPEN VENTILATED MOTORS (OUR CODE: MOV) - Three-phase motors with cast iron cage - IP23 protection - Class F insulation - Heating class B - Legs molded in the casing - Stored in 230/400V - 400/690V - Operating in 50/60hz - Cooling IC01 - Other special voltages or insulation class H on request - Stored speed : 3000 rpm or 1500 rpm or 1000 rpm - Efficiency IE4 - Form B3-B5-V1-B35-V15 - Standard motors equipped with PTC sensors for all motors
Request for a quoteBelgium
"Slip ring motors are often used in applications where the maximum transient torque must be greater than a conventional cage induction motor, such as quarries. SLIP RING MOTORS (OUR CODE: MB) - Three-phase wound rotor motors - Standard cast iron housing - Stored in IP55 protection and on request in IP23 - Stored in 230/400V from 22kW to 315kW , 400/690V to 560kW - Operating in 50/60hz - Other special voltages or insulation class H on request - Form B3-B5-V1- B35-V15 - Stored in S1 service or S3 service (6 starts per hour) - On request, we can supply motors for lifting applications with 1 or 2 cylindrical or conical axes - Standard motors equipped with PTC sensors - Equipped with roller bearings for belt drive - Electrolytic starters are stocked to start these motors"
Request for a quote