With the Drum pump F/FP 425 there is less than 0.05 l residual amount left in a 200 l drum, so maximum 0.02 %. The pump has an integrated backflow valve that is easy to close before taking the pump out of the container. Thus the backflow of the medium in the pump is prevented. This makes optimum use of especially expensive media possible and saves additional cleaning and disposal costs when handling problematic media. The pump is available in stainless steel, polypropylene and hastelloy C. In stainless steel and hastelloy C the pump F/FP 425 can also be used in hazardous areas. Benefits: - Optimal residual emptying with e.g. less than 0.05 l residual amount left in 200 l drum - Two adjusting levers to easily close the backflow stop - No tilting to totally empty the drum - Reduction of cleaning and waste disposal costs - No loss of medium when taking the pump from drum to drum - Optimal use of fluids
Germany
The Drum pump F/FP 427 is ideal for hygienic applications and suitable for conveying media out of drums, IBCs and other containers. It can be easily and quickly disassembled for cleaning / sterilization and can be completely stripped down to individual parts. The pump has minimal dead spots. The drive shaft, the inner and the outer tube are made of stainless steel (316 Ti resp. 1.4581). The pump is also available as FOOD and 3A certified version and complies with international safety standards. Benefits: - Ideal as hygienic pump - Can be quickly and easily taken apart for cleaning - All parts in contact with the medium can be sterilized - Transfers also fluids containing solids such as juices with pulp or soups with spices - Available with different connection at the pressure side (e.g. Clamp 1 1/2" or RD 58x1/6) - Available with 3A Certificate - Available as FOOD version - Appropriate for food contact acc. to EC 1935/2004 and FDA CFR 21
Request for a quoteGermany
The horizontal Drum and container pump F 430 TR is ideal for conveying media from IBCs, tanks and other containers with low level outlet. E.g. if a tank is not accessible from the top, or if the spatial conditions do not allow use of a vertical pump. For cleaning, the pump can be easily and quickly taken apart in its two main components. The pump is available in stainless steel or polypropylene. The stainless steel version can also be used in hazardous areas. Benefits: - For containers with floor drain - Provides highest flexibility in installation and mobility - Can also be used at low ceiling heights - Stainless steel version for use in hazardous areas - Can also be integrated into pipe systems - A horizontal centrifugal pump that can be used with different FLUX motors
Request for a quoteGermany
The horizontally installed, compact container pump MINIFLUX is designed for emptying IBCs via their floor-level outlet. Designed as an alternative to a vertical pump, the MINIFLUX can be used when an IBC is not accessible from the top. It is suitable for applications when gravity draining via the outlet tap is insufficient e.g. rapid dispensing or transfer to another container in a higher location. Power can ideally be provided by a commutator or compressed air motor. Benefits: - Can be used where ceilings are low - Allows pumping directly from floor-level outlets, even when containers are stacked - Significantly higher flow rate and pressure compared to draining by gravity - Minimal space requirement - Simple disconnection from IBC with union nut - Delivery against closed valve (e.g. hand nozzle, flap valve etc.) possible - Suitable for use in hazardous areas zone 1
Request for a quoteGermany
Pump F 430 PP 100/50 in polypropylene was designed for higher delivery pressure. Instead of a rotor, it is equipped with an impeller in a pump housing. In connection with the powerful FLUX motors the pump delivers a far higher pressure of over 3 bar compared to pumps with semi-axial rotors. This makes it especially convenient for conveying media out of e.g. IBCs and other containers into higher lying pipe systems or out of an IBC in the basement to a higher floor. Benefits: - The pump has a significantly higher delivery head in the range up to 40 l/min compared to pumps with half-axial rotor (Z-rotor) - Allows the conveying of media out of an IBC stock in the basement into higher floors - Ideal for pumping media into a higher lying pipe system - Can be used as a supply pump of line networks e.g. for feeding of process water
Request for a quote