EGE-ELEKTRONIK SPEZIAL-SENSOREN GMBH

EGE flow sensors without integrated Amplifier permit the space-saving flow measurement on site and the comfortable setting of the limit value using separate amplifier, e.g. within a control cabinet. The measurement takes place without mechanically moving parts using a thermal measuring element. The current flow state is displayed at the amplifier using LEDs. The sensor can be exposed to high temperatures. The devices are used wherever a safe, robust and low-maintenance monitoring of flow values is required. This includes e.g. cooling circuit monitoring, monitoring of the flow rate of process fluids, monitoring of metering processes or also for pump protection in process and factory automation.

EGE Ex-amplifier complement the EGE flow sensors without integrated amplifier. Flow sensors with approval for operation in explosive areas must be connected to approved Ex amplifier. EGE amplifier for ATEX-compliant operation supply the sensors via an intrinsically safe power circuit and provide electric separation from the mains. The amplifier itself must always be installed in areas which are not explosive.

EGE compact devices for the flow monitoring of gaseous media contain measuring and amplifier in a single housing. They are used where a visualisation of the flow rate on site is required. EGE flow sensors for gaseous media feature two pins which contain the thermal measuring elements. The sensors are set up directly at the device. EGE sensors for gaseous media are characterised by a rapid response capability and reliable operation. Based on the principle, there are no moving parts in the air flow monitors and they can, therefore, also be used in aggressive environments. Devices for air conditioning technology have smooth measuring surfaces and need not protrude far into the flow duct.

EGE capacitive level sensors for adhesive media offer the reliable monitoring of the filling level of granulate, powders, solids, such as feathers, fluids and aggressive as well as adhesive media. The medium to be detected functions as dielectric. The medium in touch with the sensor generates a capacity change. This is converted into a switching signal or an analogue 4...20 mA output signal. Level sensors of series KGFR are ideal for media with low DK value. The PTFE sleeve makes the sensor resistant to aggressive media and together with the round design ensures the fast slippage of the medium.

EGE flow sensors for gaseous media in explosive areas permit the space-saving flow measurement on site and the comfortable setting of the limit value using separate amplifier. The measurement takes place without mechanically moving parts using a thermal measuring element. The current flow state is displayed at the amplifier using LEDs. The devices are used wherever a safe, robust and low-maintenance monitoring of flow values is required. The measuring sensors of the product series ST 400 Ex; STS; STEX have ATEX approval and may, dependent on their design, be used in Gas-Ex areas requiring equipment for EPL Ga or EPL Ga/Gb. In the Dust-Ex area their use is permitted up to EPLDa.

EGE flow rate sensors for the flow rate detection of 10...100 l/min feature one-piece measuring tubes with an inner diameter of 20 mm from highly resistant stainless steel V4A (1.4571). For particularly aggressive media EGE offers special materials, such as bronze, Hastelloy, titanium or even PTFE. The devices can either be set up intuitively using a potentiometer and LED indications or easily programmed using buttons and a multi-segment display. EGE flow rate sensors can be installed in circuits with corresponding pipe diameters using threaded fittings or compression fittings. The provide excellent measuring results wherever the safe, robust and low-maintenance monitoring of low flows is required.

EGE microwave level sensors monitor the filling level of fluids, powders and granulate with a low DK value and are particularly resistant to adhesion. The MFC sensors are also suited for separation layer detection. The sensitivity is adjustable. The sensors are based on a special variant of microwave frequency shift technology. EGE supplies the sensors in varying lengths up to 1000 mm. The stainless steel and PTFE sensor tip is suited for use in aggressive media.

EGE inductive sensors for high mechanical loads still work trouble-free even after 10 impacts of 8 Joule. The sensor protected by a solid stainless steel sleeve is thus particularly resistant to shock and vibration. They are ideal for areas where standard sensors could be damaged mechanically. EGE offers variants resistant to high pressure cleaning with protection class IP 68/IP69 for use at temperatures up to 110° C and contamination-resistant sensors with PTFE coating. The proximity switches are based on the proven inductive principle and switch con tactless when a metallic object moves close. The sensors are particularly suited for heavy duty use, for example in metal processing, during welding and in mobile machinery.

EGE flow rate sensors for the flow rate detection of 1...10 l/min feature one-piece measuring tubes with an inner diameter of 4...10 mm from highly resistant stainless steel V4A (1.4571). For particularly aggressive media EGE offers special materials, such as bronze, Hastelloy, titanium or even PTFE. The devices can either be set up intuitively using a potentiometer and LED indications or easily programmed using buttons and a multi-segment display. EGE flow rate sensors can be installed in circuits with corresponding pipe diameters using threaded fittings or compression fittings. The provide excellent measuring results wherever the safe, robust and low-maintenance monitoring of low flows is required.

—Capacitive proximity switches for the detection of non-metallic and metallic objects with high switching distance up to 100 mm —Hysteresis for large moving objects —For the detection of large moving non-metallic and metallic objects