France
The company ETS JOLY AUNEAU, founded in 1999, which operates in the Plaster and plaster products industry. It is based in Champtoceaux, France.
Other companies in the same industry:
Unknown
34 T Rue Jean V
49270 Champtoceaux - France
France
TECHNICAL DETAILS Powder filler for all types of interior filling work on uneven substrates. SEMIN HIGH BUILD FILLER has very good filling properties. SUITABLE SURFACES All types of interior surfaces: bubbled concrete, untreated concrete, cellular concrete, irregular plaster, heating ceiling, terracotta tiles, uneven substrates... Covering After the filler has dried completely, suitable for covering with all types of plaster-based coatings, thick coatings, wall paper paste, wall coverings. REFERENCE DOCUMENTS • Filler complies with standard NFT 30 608 • DTU 59.1 : painting work • Technical notice CSTB N°9/99-681 TECHNICAL CHARACTERISTICS • Granulometry : up to 0.5 mm • Adhesion : complies with NFT 30 608 • pH : neutral • Usage time for batch : 24 hours PACK SIZE 25 kg bags on shrink-wrapped pallet. APPLICATION May be applied manually with a smoothing trowel or coating blade, or mechanically by spraying then manual smoothing. THICKNESS OF APPLICATION Up to 5 mm in one pass.
Request for a quoteFrance
TECHNICAL DEFINITION Ready-to-use, solvent-free adhesive primer for smooth or hardly porous substrates, for interior and exterior use. BETON HAFTGRUND allows to achieve an adhesive bridge between such substrates and certain cementor plaster-based products with a relatively low bond. COMPOSITION AND APPEARANCE Pink, ready-to-use primer with visible grain. Paintlike consistency. ACCEPTED SUBSTRATES Can be applied onto interior and exterior walls, and also onto ceilings. • Smooth cast-in-place concrete • Self-levelling concrete • Old paintwork • Old painted fibreglass coverings APPLICATION BETON HAFTGRUND is to be applied using a brush or a woollen roller. Apply a liberal coat onto the substrate and allow to dry before covering. The drying time will depend on the substrate and ambient conditions. As a general rule, allow for approximately 6 hours.
Request for a quoteFrance
TECHNICAL DEFINITION FIBRELASTIC is a ready-to-use filler paste with a high proportion of resin and glass fibre. Particularly suitable for all types of interior and exterior filling jobs. It has permanent flexibility allowing it to tolerate flexing of the substrate without cracking and it eliminates the need for repair tape. COMPOSITION AND APPEARANCE Emulsion resin, calcium carbonate, fibreglass and various additives. The paste is off-white. ACCEPTED SUBSTRATES • Plaster • Masonry • Cellular concrete • Wood • Cement render • Plasterboard • Roughcast • Old painted surfaces • Concrete • Silico-limestone brick SUITABLE SURFACES Once it has dried entirely FIBRELASTIC can be covered with any type of paint or plaster base or ready-to-use fillers. TECHNICAL CHARACTERISTICS • Viscosity (BV 1000 / 30 rpm) : 300000 mPas • Density : 1.3 • pH : 6 • Permanent elasticity PACK SIZE Tubes containing 300 g. Tubs containing 1.5 and 5 kg.
Request for a quoteFrance
TECHNICAL DEFINITION Ready-to-use coating paste coating specially formulated for use on tapered-edge plasterboard joints, to be used with jointing tape. The coating comes mixed : it is suitable for gluing and finishing the tape. COMPOSITION AND APPEARANCE Resin, water, calcium carbonate, preservatives and various additives. The paste is white in colour. TECHNICAL CHARACTERISTICS Cracking : Up to 5mm thickness with no cracking. APPLICATION Application is carried out manually, spreading the thinned the product with a coating knife across 10 or 15 cm, before laying the tape in position. In the event of projecting vertical angles, use reinforced tape (frame placed at the side of the panel). Apply tape to the internal ceiling corners, making sure that the concrete is free of any trace of forming oil. The surface must be dry and free of any type of powder or insufficiently adherent product.
Request for a quoteCreate one request and get multiple quotes form verified suppliers.