Viet Nam
Manufacturer/ Producer
We are InoxHoaBinh company, Stainless steel manufacturer in VietNam .We have 5 factories located in North Vietnam and many branches in all over VietNam, one office in USA.We are the only producer in VietNam can offer a wide range of stainless steel products : Stainless Steel Coil, Strip, sheet; Stainless steel pipes, tubes, angles, wires&bars.These high quality products are certified TCVN-VietNam, ASTM-USA, JIS-JAPAN standards.Our products are exporting to USA, Korea, Turkey, Thailand, Taiwan, Indonesia, Singapore, Cambodia, India, Malaisia and others Asia countries, ..We hope that we can have business and co-operateIf you have any demand, pls do not hesitate to contact me at anytimesLooking forward to receiving your reply! Mr.Vu Quang LongMobile: +84 902340025Inox Hoa Binh Joint Stock companyEmail: longvq@inoxhoabinh.vn stainless@inoxhoabinh.vnWeb: http: //www.inoxhoabinh.vnYm! : inoxhoabinhvnHotmail Msn : inoxhoabinh@hotmail.comSkype: inoxhoabinhGtalk Gmail :
Manufacturer/ Producer
GiaiPham,YenMy,HungYen
10000 HaNoi - Viet Nam
France
Stainless steel 1.4404. Version: Satin finished. Note: The hinges are made of weldable profile steel. The pin is fixed into the lower part of the hinge. The differing steel qualities of the weld and the beam onto which the hinge is welded must be at least equal to or better than: Stainless steel 1.4404
Request for a quoteFrance
Stainless steel 1.4305 Lamellar insert polyamide (PA6). Seal ring CR / NBR. O-ring NBR. Version: Bright. Note: DIN EN 60423 cable glands with metric thread. Sealing and tension relief are provided by inset fins and a sealing washer. Rating IP68 (5 bar for 30 min). Cable glands are used for connecting fixed calbes and lines in housings, distributors and switch boxes. Temperature range: Static: -40 °C to +100 °C. Dynamic: -20 °C to +100 °C.
Request for a quoteFrance
Coupling stainless steel 1.4057. Screws stainless steel 1.4301. For applications that require a small construction volume and low surface pressure. The keyless locking coupling can be fully recessed in a hub connection. for shaft diameters 6 20 mm suitable for hubs with low wall thickness minimum axial offset possible selfcentring Assembly Lightly oil keyless locking coupling on the tapered faces and contact points of the shaft and hub. Do not use MoS2 or grease. Insert keyless locking coupling in the hub seat and slide onto shaft. Tighten screws crosswise in several increments to the defined tightening torque. Dismantling Remove all screws and screw into the extraction threads of the front flange. Tighten screws crosswise in several steps until the keyless locking coupling loosens. Tolerances Shaft Recommended tolerance h8. Surface quality Rz ≤ 16 µm. Hub Recommended tolerance H8. Surface quality Rz ≤ 16 µm.
Request for a quoteFrance
Shrink disc to connect a hollow hub to a shaft. They are mounted on the OD of the hub and generate pressure on the hub wall by reducing the ID with wedgeformed rings, creating a press fit between the hub and shaft. They are suitable for static, dynamic and shock loads. for extremely high torques no axial shaft/hub offset when assembling selfcentring The version 23380014072 has high tensile ISO 4762 screws. Assembly Remove existing transportation locks. Clean and lightly oil shaft, internal and external hub diameters. Do not use MoS2 or grease. Slide shrink disc onto hub. Then slide unit (shrink disc/hub) onto shaft and position correctly. Gently tighten clamping screws one after the other by hand. Then use a torque wrench to tighten the clamping screws crosswise in several increments to the defined tightening torque MS. 1st increment approx. 33% MS 2nd increment approx. 66% MS
Request for a quoteCreate one request and get multiple quotes form verified suppliers.