LICHTGITTER GMBH

Marinas, sports facilities or boat and canoe jetties. Landing stage gratings are the best flooring for such systems and at the same time enhance each construction project with the unique appearance. Instead of cross bars, rounded brackets 20 x 10 x 2 mm are pressed into the bearing bars so that trouble-free walking is possible even without shoes. — perfect for floor coverings that are walked on withou shoes — high load capacity at low weight — Corrosion resistant because of hot-dip galvanization according to DIN EN 1461

The perforated metal plank BZ-Gv “Zahn, groß, verkehrt” offers a free cross section of at least 70%. It is therefore suitable for use in intermediate levels. Through the use of BZ-Gv profiles, the there is no need for a sprinkler system below these intermediate levels. Optimal flue exhaust and sprinkler suitability are thus guaranteed.

The perforated metal plank type BN-OP5 “Noppe, offen plus, 5mm“ was especially developed for pedestrian areas with „High Heel Proof“ requirements. The bothsided punched holes have a diameter of 5mm. The punching sequence corresponds to BN-OP7. This type of planking offers high slip resistance and also allows ladies in stiletto heels to walk safely on the gratings. Due to the small hole configuration it is difficult to see through from underneath, which is important in public access areas. The perforated metal plank type BN-OP8, corresponds to type BN-OP5 in terms of the punching pattern, but have twice the number of holes. The drain holes have a diameter of 8 mm and thereby increase the drainage performance and light and air permeability..

The perforated metal plank type BN-OD „Noppe, offen , different“ is characterised by two different hole sizes. The bothsided punched holes have upwards a diameter of 14 mm and downwards a diameter of 7 mm.

The perforated metal plank type BZ-GP has been developed from our approved planking type BZ-GP. Because of the homogeneous surface it is easy to negotiate. Furthermore the free cross section of 70 % makes a high light permeability and sprinkler suitability possible. Therefore the profile is particularly suitable for suspended ceilings. There is no need for sprinkler systems below the suspended ceiling. Due to the high point loads, additional planking during the assembly or later is not necessary. Thus, an ideal smoke funnel, sprinkler suitability and efficiency are guaranteed.

The perforated metal planks, type BN-O33 “Noppe, offen” combines top and bottom pressed nubs with a hole diameter of 8 mm: This provides excellent stability and drain holes for a good drainage effect. In combination with the profile BN-O33vi for steps with vi-nosing or the closed profile BN-G33 it results in many applications and variations.

The perforated metal planks, type BN-G33 “Noppe, geschlossen” has upwardly pressed closed nubs and provides a high slip resistance. BN-G33 is suitable for indoor in combination with BN-G33vi stairtreads. BN-G33 is suitable for areas where on the one hand a closed surface is desired and on the other hand a good accessibility must be guaranteed.

The perforated metal planks, type BN-G “Noppe, geschlossen”, the punched nobs pressed upwards are closed and offer high slip resistance. BN-G gratings are often used in indoor environments and there, where, on the one hand, a closed surface is desired and on the other, good accessibility must be ensured.

The surface of the perforated metal plank, type BN-GA is a mix of closed punched nobs facing upwards and conical drain holes facing downwards. This means that the grating does not have any sharp edges on top and can be walked on easily even without footwear. At the same time, however, any liquids can be quickly drained through the conical drain holes so that no hydroplaning can occur.

With perforated metal planks, type BN-O “Noppe, offen“ the bothsided punched holes have a diameter 8 mm and allows an excellent standing stability. Furthermore the drain holes exhibit good drainage. The BN-O grating guarantees a high stability for normal pedestrian traffic.