NORELEM FRANCE - Leader mondial des composants standard destinés à la construction et à l’ingénierie mécanique

UNI lock double clamp modules are particularly suitable for the direct clamping of workpieces. Workpieces with complex geometry can be completely machined on 4 and 5 sides. UNI lock double clamp modules can be mounted in any position. The high clamping forces are generated by the integrated spring package. (the unit clamps while not pressurised). Clamping is released pneumatically. The following clamping forces are possible with the UNI lock clampng pin in conjunction with M10, M12, M16 fastening screws: Clamping force (M10) 35,000 N Clamping force (M12) 50,000 N Clamping force (M16) 75,000 N Supplied with: 1 double clamp module incl. 3x pneumatic connections.

Interchangeable subplates are particularly suitable for quickly exchanging fixtures on zero point clamping plates. Ground on both sides, standard clamping pin gauge of 200 mm. Complete with clamping pins and handles. On request: Further gauges and special sizes.

Locating cylinder tempered, black oxidised. Balls hardened, bright. Note: Locating cylinder with quick-clamp system for extra timesaving during setups. Insert the locating cylinder into the receiving hole and press the button. The three balls are pushed out and position the components. By tightening the set screw a 1/4 turn using an hexagonal key, the components are positively and securely held.

Housing hardened and black oxidised. Contact faces ground. Note: This positioning and clamping system is especially suitable for installation in fixtures (plates, clamping tower blocks, etc.) in all mounting positions. The modular design allows the number of and distance between the locating cylinders to be ideally adjusted to suit the clamping task. Due to the small diameters, the spacing between the locating cylinders can also be reduced. The 3 clamping balls are mechanically released through control of the locating cylinder with the "opening" connection. The 3 clamping balls move inward and the fixture can be changed quickly. For clamping, the air is taken from the "opening" connection and the "clamping" connection then receives air on the locating cylinder. The 3 clamping balls are mechanically driven outward again and the new fixture is clamped. To achieve optimal retaining force, the locating cylinder remains connected to the air.

Housing hardened and black oxidised. Contact faces ground. Note: Locating bushes are placed in a fixture or interchangeable subplate and form the counterpart to the locating cylinder. The locating bushes are centred in a reamed hole and then fastened with 4 screws. The balls of the locating cylinder engage in the groove in the locating bush, thereby forming a fast, secure and highly accurate changeover unit, and reducing setup and changeover times. Attention: Please observe installation notes of the locating bushes.

Main body oxidised. Contact faces hardened and ground.

Body and clamping pin oxidised. Contact faces hardened and ground. Note: The UNI lock 5-axis add-on modules are used for raising basic modules and mounting base. Depending on the clamping situation, optimum assembly height can be achieved using a combination of the basic module and add-on module.

Flange plate, piston and body rust-resistant, bright. Screws electro zinc-plated. Collet red or clear anodised. Note: Machinable collet system with base plate for mounting on 50mm pitch grid plates. The flange plate can be used for external or internal clamping collets. The contour of the workpiece to be clamped is machined into the collet. Free-form and asymmetrical contours can be clamped. The integrated spring package generates a clamping force of 5.8 kN. The clamping force can be raised to 43.5 kN by pneumatic post-clamping. The clamp is released by blowing compressed air onto the lower piston surface pushing the piston upwards and releasing the clamping force on the collet. Clamping travel 0.2 mm. Repeat accuracy < 0.01 mm. Accessory: Collet for external or internal clamping 03179

The 5-axis vice features excellent stability and flexibility, and is extremely easy to use. The 5-axis vice can be used as a positive-down force vice or normal vice. When the positive down force function is used, the workpiece can be held with a repeat accuracy of ±0.01 mm. A workpiece clamping height of 180 mm enables easy access during machining. The clamping width is preset using the crank handle, cutting down on setup times. Additionally, the closed geometries and the resistance to dirt that they provide keep maintenance and repair times to a minimum.

The easy operability and rapid adjustment using a scale means that the clamping jaws can be quickly and surely adapted to new workpieces The workpiece is always centred through the systematic construction of the 5-axis compact clamping system. The optimal accessibility to the workpiece allows short, standard tooling to be used. Tooling costs are significantly reduced. Positive down force by a clamping depth of >5 mm. Clamping widths of 20 mm to 320 mm are possible. Assembly: The 5-axis clamping system compact can be mounted on T-slot tables, grid systems or, using an adapter flange on conventional zero-point clamping systems. Accessory: Seating ledge 41345 Jaw plates 41320 Pendulum jaws 41325 Centre jaws 41335 Coupling for cross-clamping 41365 Order the seating ledges and jaw plates with pins separately.