Angle flanges - Import export

Compact flanged angle seat motor valve for on/off and modulating operation for neutral and aggressive media. Flanges acc. DIN EN 10921 Flanges acc. ANSI #150, ANSI #300 Positioner electronics Limit switches Position feedback. All control actuators are also available with fail safe feature. Low temperature version Pressure balanced version Degreased version, Silicon or PTFEfree version …

Pneumatically operated angle seat flange valve for high switching powers. In stainless steel design also suitable for neutral and aggressive media. The angled seat design offers a high flow rate, the flange connection offers easy installation. Flange acc. to DIN EN 10921 Flange acc. to ANSI #150, ANSI#300 Limit switch Pilot valve Manual override . . .Piston actuator of Brass (chrome plated) Stainless steel Polymer Stainless steel diaphragm actuatorLow temperature version Pressure balanced version Degreased version, Silicon or PTFEfree version …

The integrated gearbox/pinion combination provides the best technical coordination for rack and pinion drives. Numerous solution options provide high dynamics and high load-bearing capacities at the same time because of the precision gearing Our WPSFN is extremely light and easy to integrate thanks to its standardized flange interface. It achieves optimized synchronization with the spiral gearing and the helical-toothed planetary stage for the best surface qualities. The shortest right angle precision gearbox with integrated hollow shaft provides you with new structural solutions.

The shortest right angle planetary gearbox with flange output shaft and maximum torsional stiffness. Thinking around corners even in tight spaces. The WPLFE is our right angle planetary gearbox with compact flange output shaft. You save up to 30% more space and benefit from torsional stiffness that is five times higher than conventional products. Thanks to its standardized flange interface, it's especially easy to install. The integrated dowel hole provides additional secureness during fitting.

The integrated gearbox/pinion combination provides the best technical coordination for rack and pinion drives. Numerous solution options provide high dynamics and high load-bearing capacities at the same time because of the precision gearing Our WPSFN is extremely light and easy to integrate thanks to its standardized flange interface. It achieves optimized synchronization with the spiral gearing and the helical-toothed planetary stage for the best surface qualities. The shortest right angle precision gearbox with integrated hollow shaft provides you with new structural solutions.

The Morgan Rushworth hydraulic punching machines are available in models from 70 tonne up to 175 tonne capacity. All double punch models are equipped with a 625mm deep throat one end and a 305mm the other as standard configuration. The heavy-duty support table with adjustable backstop, universal die holder for the punching of plate, flat bar, angle iron and flange of channel and beam are all included in the standard execution. The punching machines are also available in single-ended configuration. The standard machine allows punching of up to 57mm diameter without additional equipment. The front section of the support table can be removed in order to punch angle-iron leg down. A wide range of options are available including bar bending, sheet bending and corner notching.

The Morgan Rushworth hydraulic punching machines are available in models from 70 tonne up to 175 tonne capacity. All models are equipped with a 625mm deep throat as standard. The heavy-duty support table with adjustable backstop, universal die holder for the punching of plate, flat bar, angle iron and flange of channel and beam are all included in the standard execution. The punching machines are also available in double-ended configuration. The standard machine allows punching of up to 57mm diameter without additional equipment. The front section of the support table can be removed in order to punch angle-iron leg down. A wide range of options are available including bar bending, sheet bending and corner notching.

Compression Proof and Form Stable Biaxial expanded Joint Sealant Characteristics No change in width at compression Excellent on slim or restricted flange area Technical parameters pH 2 - 12 Temperature: t = -200 … +280 °C Pressure: p = Vacuum … 200 bar Density: 0,95 g/cm 3 Main application Larger flanges and vessels Glaslined flanges Agitators Heat exchangers Form of delivery 10 mtr / roll Other length and dimension on request Suitable for Pharmaceutical industry Food industry Approvals FDA21 CFR 177.1550 (PTFE), FDA21 CFR 170.105 (adhesive) EG 1935:2004 EU 10/2011 FDA Installation Instructions Connect the ends with an angle cut Maximum uneveness of flange: 1/3 of seal tape’s thickness Dimensions thickness (mm) Recommended for Steel Flanges width according DIN 2690 (NW) Surface pressure/ resulting thickness in 10 N/mm2 Surface pressure/ resulting thickness in 20 N/mm2 Surface pressure/ resulting thickness in 30 N/mm2 Surface pressure/ resulting thickness in 40 N/mm2 2 ≤...

Our SA series contains copper weld elbows according to [DIN 2607 - insert UK norm], torispherical heads for the pre-welding and angle flanged wheels for pre-welding.

10 x modular painted steel formwork panels 3m x 2m 20 × Single or variable GP10 alignment flanges 20 × Tightening rod 750 cmm DW15 + 2 nuts DW15 2 × GP10 lifting hooks 5 × Double push pull props GP10 5 × Service consoles with blockers 1 x Inside angle H: 3m, 0.30x0.30 m 1 x painted steel modular formwork panel 0.60 x 3m 1 x painted steel modular formwork panel 0.50 x 3m 2 × Compensation 3000 x 100 mm 2 × Compensation 3000 x 50 mm 3 × Variable angle flanges GP10 8 × GP10 Variable Alignment Flanges 1 x Accessory box 120x80

-20 x modular painted aluminum manual formwork panels 3m x 1m - 40 × GP10 single or variable alignment flanges - 33 × Tightening rod 750 cmm DW15 + 2 nuts DW15 - 2 × GP10 lifting hooks - 5 × GP10 double push pull prop - 5 × Service consoles with blockers - 1 x Inside angle H: 3m, 0.30x0.30 m - 1x manual painted aluminum modular formwork panel 0.60 x 3m - 1 x painted aluminum modular panel 0.50 x 3m - 2 × Compensation 3000x100 mm - 2 × Compensation 3000x50 mm - 3 × Variable angle flanges GP10 - 8 × Variable alignment flanges GP10 - 1 x Accessory box 120x80

This pack consists of -20 x painted steel modular formwork panels 3m x 1m - 40 × GP10 single or variable alignment flanges - 33 × Tightening rod 750 cmm DW15 + 2 nuts DW15 - 2 × GP10 lifting hooks - 5 × GP10 double push pull prop - 5 × Service consoles with blockers - 1 x Inside angle H: 3m, 0.30x0.30 m - 1x of modular painted steel formwork 0.60 x 3m - 1 x painted steel modular formwork panel 0.50 x 3m - 2 × Compensation 3000x100 mm - 2 × Compensation 3000x50 mm - 3 × Variable angle flanges GP10 - 8 × Variable alignment flanges GP10 - 1 x Accessory box 120x80

This Pack consists of 40 x painted steel modular formwork panels 1.50 m x 1.00 m 4 x painted steel modular formwork panel 0.60 x 1.5 m 4 x painted steel modular formwork panel 0.60 x 1.5m 8 x painted steel modular formwork panel 0.40 x 1.5 m 8 × Offset 150 x 10 cm 8 × Offset 150 x 5 cm 2 × GP10 lifting hooks 4 x Inside angle H: 1.5m, 0.30x0.30 m 60 × Tightening rod 750 cmm DW15 + 2 nuts DW15 112 × Single GP10 Alignment Flanges 8 × Variable angle flanges GP10 16 × GP10 Variable Alignment Flanges 2 x 120x80 accessory boxes