Interior high build filler

TECHNICAL PROPERTIES Primer filler for vertical surfaces or for use on ceilings made from poured concrete or pre-slabs. Decorating filler, for smoothing over. Smooth, matt finish. Odour-free. COMPOSITION AND APPEARANCE. Solvents : Water. Filler : Calcium carbonates. Additives : Dispersing agent, bactericidal fungicide. Thickeners : Cellulosic, polyacrylates. Binders : Acrylic dispersing agent. Density : 1.86. Dry matter : 75%. TECHNICAL PROPERTIES • Fire classification: A2-S1, d0 SUITABLE SURFACES Interior : ideal for covering bricks, brick tiles, cement breeze blocks, cinder blocks, de-bubbling pre-slabs, shuttered concrete, aerated concrete, for redecorating stippled walls or old damaged surfaces. APPLICATION. • The first coat should be levelled out using 60 cm scraper or skimmed with a rule. • After drying, the second coat should be smoothed with a scraper. • After allowing to set slightly, squeeze the filler at a slight angle using a clean scraper.

TECHNICAL DEFINITION SEMIN AIRLESS 3 IN 1 is an indoor filler that can be used as an Airless spray. It provides an even appeareance without smoothing, has great coverage and a deep matt finish. It combines 3 actions : underlayer, filler and finish. COMPOSITION AND APPEARANCE Acrylic emulsion resin, mineral content, cellulose derivates, preservation agent and other additives. The resulting paste is a bright white colour and its consistency is adapted to its airless application. TECHNICAL CHARACTERISTICS • Dry extract : 68% • Density : 1,76 • COV : <1g/l APPLICATION SEMIN AIRLESSS 3 IN 1 can be sprayed with all kinds of Airless machines adapted to srpraying coatings. Recommended nozzle : 627. For optimum results, we recommend following this method : • Spray a first layer of the coating about 300 to 400 g/m2, to show up the defects on the surface. Spray at a distance of about 80 cm from the relevant surface • Check over the surface carrefully

TECHNICAL DEFINITION Levelling filler for vertical substrates and for use on ceilings for poured concrete or pre-cast slabs. Ideal for the preparation of pre-cast slabs, formwork concrete and for the renovation of textured finishes or fibreglass with a paint finish. TECHNICAL CHARACTERISTICS • Dry extract : 75% • Density : 1.86 • VOC content : less than 1g/l COMPOSITION AND APPEARANCE Water, calcium carbonate, dispersant, bactericide, fungicide, cellulosic fibres, polyacrylates, clays, acrylic dispersant. AMOUNT REQUIRED From 2 to 4 kg for the first coat. From 1.5 to 2 kg for the second coat. APPLICATION SEMIN AIRLESS EXTREM filler is sprayed using the Airless pump or rotor machine/Flat spray stator in 2 coats. The first coat must be levelled using a 60 cm blade or levelled with a straight edge. After drying, the second coat must be smoothed using a blade.

TECHNICAL DETAILS Paste coating for a good finish on interior walls and ceilings. Provides excellent surface preparation before painting or hanging coverings. COMPOSITION AND APPEARANCE Emulsion resin, calcium carbonate, rheological agent and various additives. SEMIN ENDUIT DE LISSAGE is a water-based coating. The paste is white in colour. COVERINGS • Wallpaper • Paint • Wall covering SUITABLE SURFACES Interior walls and ceilings • Plasterboards • Plaster tiles • Concrete • Cement coating TECHNICAL CHARACTERISTICS • Density of paste : 1.9 • Granulometry : fine • pH : 7 Adhesion : complies with NFT 30 608 PACK SIZE 4 and 10 kg buckets on shrink-wrapped pallet. APPLICATION Apply manually using a smoothing trowel or a filling knife. The maximum thickness will be 2 mm per coat. Allow to harden and remove imperfections before sanding, if necessary. Print the SEMIN ENDUIT DE LISSAGE if applying satin-finish or gloss paint. Clean tools in water.