Lubrication of friction and rolling bearings, chains, joints or slideways at higher temperatures For conveying systems under radiation heat in painting, stoving and drying systems, travelling grates in firing systems Dry lubrication at temperatures above 200°C Lubrication of elastomers and plastics not resistant to mineral oil Advantages and benefits Highly suitable as a high-temperature lubricant Very effective due to finest, homogeneous MoS₂ distribution in the oil Resistant to water and many chemicals, fuels, lubricants and hydraulic oils For best adhesion, clean the surfaces. Best way is to clean mechanically first and then with OKS 2610/OKS 2611 universal cleaner. With a brush, drip oiler or by immersion or using a suitable automatic lubrication system, apply a sufficient quantity to the locations to be lubricated. If at all possible, avoid excess. Observe the machine manufacturer's instructions. Assess the lubrication frequency
Germany
Improves the run-in lubrication of new or overhauled machines and increases the load-carrying capacity Improves the lubricating properties of the oil under high loads and at high temperatures Reduces operating noises and wear Advantages and benefits Forms a pressure-resistant layer with high lubricating effectiveness Increase in the load-bearing share Reduction in the specific surface loading Lower thermal loading of the lubricant Considerably extended service lifeShake or stir well before use. Depending on loading, add 2-3% to engine oils and 3-5% to machine- and gear oils. Instructions of the machine manufacturer have to be observed. Mixing will occur in operation. Mix with appropriate lubricants only. Not suitable with water-based lubricants and polyglycol oils. Especially at older machines and machines normally used with unalloyed oils, the compatibility of OKS 30 with the installed gaskets has to be proved before application.
Request for a quoteGermany
Assembly paste for press-fitting wheels, shafts, tires or bearings Non-stick primer coat for moving threads, guides and slideways to prevent stick-slip effect, seizing and wear Wearing-in lubrication of highly stressed sliding surfaces such as plain bearings, gearwheels, crankshafts with provision of anti-seizing properties Suitable for non-cutting shaping of the difficult type, such as doming, pressing, embossing while avoiding critical metal contacts and welding Advantages and benefits Immediate effective protection against corrosion, wear and stick-slipping under high stress conditions No pressing onto the sliding surface required Highly effective due to the strong affinity of the MoS₂ for metals Extremely low friction at highest loading capability Increased operational reliability of moving parts due to anti-seizing properties Improved performance due to organic molybdenum complex compounds For optimum adhesion, clean contamination and other lubricants
Request for a quoteGermany
Lubrication of chains, hinges, joints, ejector pins, clamping and drying frames or slideways at temperatures up to 250°C or under influence of water, for example conveying systems in painting, stoving, drying and cooling bed installations Advantages and benefits Outstanding oxidation properties Resistant to water and steam Good creep properties Outstanding adhesion and lubrication effect with no tendency to drip No formation of hard residues Extreme wear protection through Moₓ-Active Resistant to ultraviolet radiation
Request for a quoteGermany
Lubricating and sealing off tap cocks, labyrinth seals, stuffing boxes and packings Lubricating and sealing off fittings made of metal, plastic and ceramic, e.g. drain, cold- and hot-water fittings Long-term lubrication of heavily loaded press and guide plates, for example on telescope booms of mobile cranes As a lubricant for of threaded spindles on radiator thermostats Advantages and benefits Reduces wear Extension of the relubrication intervals High resistance to oxidation Noise and vibration-damping Resistant to cold and hot water, water vapour, lactic, formic, acetic and fruit acid, as well as alkaline and acidic cleaning agents and disinfectants Good elastomer and plastic compatibility For optimum adhesion, clean contamination and other lubricants from slide surfaces. Best way is to clean mechanically first and then with OKS 2610/OKS 2611 universal cleaner. Apply sufficient paste evenly with a brush, spatula, etc. The paste will also act as a sealant.
Request for a quote