VINCO - Specialists in Strip, Wire and Wire Rope

FINISHES: SURFACE QUALITY PROPERTIES OF THE COATINGS GALVANISED STEEL according to EN 10142 Check our website for coating mass, coating finish, surface quality and protection surface treatment. If the customer does not require the surfaces to be oiled and/or chemically passivated, this must be clearly indicated when requesting the quote and placing the order. THICKNESS TOLERANCES Thickness tolerances according to EN 10143 for nominal widths. WIDTH TOLERANCES Tolerances on wide strips obtained by longitudinal cutting of a width of less than 600 mm.According to Standard EN 10143 of: w < 125; 125 w < 250; 250 w < 400; 400 w < 600. Other, closer dimensional tolerances under a commercial agreement. SAG TOLERANCES Edge curve tolerances under commercial agreement

SURFACE FINISH. APPROVED FINISHES EN 10202 Bright, Fine stone, Stone, Silver, Matt COATING. PRECISE VALUES FOR TIN COATINGS EN 10202 HICKNESS TOLERANCES Thickness tolerances and edge reduction according to EN 10202 The thickness of the material must meet the following requirements: a) Deviation from the agreed thickness, measured on the centre line of the strip, must not exceed ± 5%. b) Deviation from the agreed thickness, measured at any point at a distance of no less than 6 mm from the sheared edge, must be between +5% and -8%. WIDTH TOLERANCES Other, closer dimensional tolerances are possible under a commercial agreement. EDGE CAMBER TOLERANCES Tolerances for edge bending under commercial agreement.

SURFACE FINISH. APPROVED FINISHES EN 10202 Bright, Fine stone, Stone, Silver, Matt COATING. PRECISE VALUES FOR TIN COATINGS EN 10202 HICKNESS TOLERANCES Thickness tolerances and edge reduction according to EN 10202 The thickness of the material must meet the following requirements: a) Deviation from the agreed thickness, measured on the centre line of the strip, must not exceed ± 5%. b) Deviation from the agreed thickness, measured at any point at a distance of no less than 6 mm from the sheared edge, must be between +5% and -8%. WIDTH TOLERANCES Other, closer dimensional tolerances are possible under a commercial agreement. EDGE CAMBER TOLERANCES Tolerances for edge bending under commercial agreement.

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.