Vibrators- industrial - installations - Import export

Suitable for the conversion kit for shaft-driven vibrating screeds. Own vibrating beam system - must fit - compatible with almost all SVM, SVE, Vario and Variant systems. Following the modular philosophy, the aluminum A-points are screwed onto the carrier plate and then attached to the T-profiles. The patented electrified upper belt, also suitable for Mooser MSB planks, serves as a carrier system. Elements of 50cm, 75cm, 1m, 2m and 3m can be delivered. It is therefore also possible to configure a complete screed with end pieces, vibrators, winches, etc.

The MSB-SL is an infinitely adjustable vibrating screed that can be used from approx. 3m to approx. 5m and can be operated with a battery (24V) 230V and 400V. Both variants have a forward/reverse switch and speed control. Assembly is easy and can be done on site. The versions can be individually designed to meet your needs.

Brackets & adapters for compressed air external vibrators There is a mounting option for almost every formwork system. If not, we will construct a mount.

RuMoo MSB hump vibrating beam is a combination of MSB Large with crossbars on which different angles can be mounted. With spindle supports and collars, these planks are used to level the protective concrete on bridge and tunnel construction sites. However, the hump plank can be used as a straight plank in a very short time by changing the angles.

Mooser MSB conversion kit suitable for Noggerath, Belidor, Tremix, Contec, Atlas Copco - and similar screeds. Replace the patented electric top belt, mount the vibrator with the mounting plate, plug in the cable and off you go. Can also be converted directly on the construction site in just a few hours. The vibrating beam then works without a shaft, without pillow block bearings, without couplings, without rubber crosses, without V-belts and without a central drive. Top surface, adjustable speed, no open mechanical wearing parts due to vibrators encapsulated in the housing, no freezing of the (standing) bearings when water gets in in winter, no problems with buckling points...

All standard angle lengths from 0.50m to 3.0m can be used. Thanks to the kit system, the MSB small can be shortened or lengthened at any time by unscrewing or screwing on. The working width of the planks is approx. 5m. By clamping or overpressing the element clamps, radii can be approximated polygonally. Special elements with a rolled radius are also possible. The low overall height and the low weight enable use in places that are difficult to access, such as tunnel cross passage floors, tunnel intermediate ceilings or tunnel shoulders. Another area of ​​application are bridge construction sites (cap concrete/steel composite).

Due to the modular system, all attachments except for the three -point belts can be exchanged between the large and medium vibrating screeds. The MSB Medium has a maximum height of 35.5 cm thanks to the "Medium" three-point harness. The end pieces have been reduced in height but can be adapted with an attachment frame. The MSB Medium can be used up to lengths of 15 meters and more. In the case of short lengths, operation with a handle is possible. From approx. 4 - 4.5 meters we recommend using manual winches.

Low deflection in all axial directions Elements from 0.50m | 0.75m | 1.00m | 1.50m | 2.00m | 3.00m | Special lengths available. Inclination continuously adjustable up to +30° and -15° at the element joint. Quick assembly of the elements thanks to the patented tube-screw connection system

RuMoo compressed air vibrator RM - the external vibrator that can be controlled on the device The RüMoo compressed air vibrator is a new development. Air pressure and air volume, i.e. the speed and thus the vibration behavior, can be regulated on the housing of the RüMoo compressed air vibrator. This means that fine adjustments can be made in a way that was previously not possibleA wide variety of rotor weights can also be installed in the RüMoo type RM compressed air vibrator. As a result, the centrifugal force can be increased by a factor of approx. 1.8 in the same housing, for example, by changing the rotor weight. A cost-effective alternative to performance variability is therefore given. The rapid start-up of the RüMoo add-on vibrator runs through the natural frequency of the respective component in a matter of seconds, a component is dynamically stressed as little as possible. With the RüMoo type RM60, concrete compaction depths of up to 80 cm and more