Epoxy adhesives - Import export

1)Epoxy self-leveling floors are mainly used for floors with high requirements for cleanliness and certain mechanical properties and aesthetic requirements. 2)Structure for Self-Leveling Epoxy Paint --Polish the sub-base --Primer --Strength layer --Sanding the floor --Putty layer --Troweling self-leveling epoxy top coat 3)Features Two-component material, used together. Seamless dust-proof, pressure-resistant, impact-resistant Good wear resistance and long service life Aseptic and dust-free

Rotafix Zeroset Anchor Grout is a 2-part high strength epoxy system that is used for the fixing of metallic objects into concrete such as anchors and studs. Rotafix Zeroset Anchor Grout has been specifically designed for setting at low temperatures in smooth-walled, diamond drilled holes. This chemical anchor will displace water from a hole then cure under any residual water. This high-performance chemical anchor grout has been approved by the Department of Transport for parapets and street lighting. Additional Information: Compressive Strength: 70N/mm2 Tensile Strength: 16N/mm2 Flex Strength: 32N/mm2 Workable for 20 minutes at 20°C Available Sizes: 500cc (Product code: 3542)

Rotafix Engineering Adhesive is a high strength structural epoxy adhesive, part of the Resiwood product range. The 2-part unfilled epoxy adhesive has a degree of flex which makes it well suited to wood engineering and timber applications. The slow setting nature of Rotafix Engineering Adhesive lends itself to working on site where time is needed to create and move joints prior to finalising the assembly. Additional Information: Compressive Strength: >60N/mm2 Tensile Strength: 40N/mm2 Tensile Modulus: 3GPa Flex Strength: 70N/mm2 Bond Strength: 6N/mm2 Specific Gravity: 1.1 Workable for 6 hours at 20°C Supplied with: Cartridge set Nozzle Follower plate Available Sizes: 400cc (Product code: 3560)

Rotafix Structural Adhesive (RSA) is a high performance unfilled thixotropic slow setting structural epoxy adhesive which is used in timber engineering. The slow setting nature of the epoxy adhesive allows the manipulation of timber joints for a period of time. This is particularly useful for flooring boards, roofing sheets or complex joints. RSA is used extensively for: Bonding rods and plates into timber engineering repairs, such as Timber Resin Splice Upgrading timber strength using bonded in flitch plates GluLam delamination repairs using rods Construction in wood Structural joint glue Moment resisting joints Stressed skin floors Additional Information: Compressive Strength: >60N/mm2 Tensile Strength: 38N/mm2 Tensile Modulus: 2GPa Flex Strength: 70N/mm2 Bond Strength: 6-10N/mm2 Specific Gravity: 1.1 Workable for 6 hours at 20°C

DELO-KATIOBOND UV curing (320-400nm) and light activated (400-550nm) epoxy adhesives are one part solvent free epoxies suitable for bonding, sealing and potting applications. DELO-KATIOBOND light activated adhesives can be used in opaque applications, as once the adhesive has been initiated via visible light, curing starts due to the decomposition of the photo-initiator and continues to completion. The curing is by cationic polymerisation, hence the product name Katiobond. Information on UV Curing Lamps can be found here. The range has good temperature resistance, up to 180 degrees C and excellent chemical resistance, making them ideal for automotive and harsh environment use. The epoxies are dry to touch after cure (no oxygen inhibition occurs). Cured products exhibit low shrinkage, resulting in low stress on delicate devices. Low water absorption and very low ionic content make them ideal for electronic applications. ** Click for more **

Adesivo EXTRA STRONG per incollaggi ad alta esistenza. Trasparente, universale e riempitivo. Il formato ideale per la casa e i tuoi hobby. LA BICOMPONENTE PER TUTTI! CON SIRINGA PER UN DOSAGGIO PERFETTO.

Low shrinkage optical camera module adhesive with LED and/or heatcure for common substrates used in camera modules and LiDAR assemblies, in active alignment, and other optical bonding applications. Features: - Rapid LED or UV/Visible light and/or heat cure - Very low volumetric shrinkage - High Tg and Low CTE - Low ASTM E595 Outgassing - No frozen storage, refrigerated shipment/storage 15°C [3441° F]

Short description: With double syringe This transparent adhesive retains elasticity after curing and is ideal for jobs in construction and assembly and in fact in all cases where the use of WEICON Easy-Mix Systems would not be efficient. Viscid, self-levelling, very short pot life (3 - 4 minutes), fast-curing, almost colourless, glass clear. WEICON Epoxy Minute Adhesive is especially suitable for occasionally necessary repair and maintenance works. It is applied by using the practical double syringe. This means that resin and hardener are delivered automatically in the right proportions. After this, the mixing is done manually.

Low shrinkage optical positioning Epoxy with LED and heatcure capability. Features: - Fast cure with LED or UV/Visible light - Low temperature heat cure (8085°C) - Low shrinkage and CTE - Single component - Cold ship/Cold storage at 15°C - Passes ASTM E595 Outgassing Testing

It efficiently grinds adhesives, paint, epoxy and spackle. With a grinding width of 280 mm it is suitable for small to medium concrete areas. 

Examples of materials for dosing: 1- and 2-component epoxy, UV / light-curing / thermosetting adhesives, highly filled materials, anaerobic adhesives, shear-sensitive adhesives, heat-conducting paste, sealants, flavourings, silver conductive paste, flux, perfume, isopropanol, industrial oils, silicone, alcohol, grease, paint and ink, MEK, braze paste, PU, acetone, petrol and many others. The preeflow® eco-DUO is a rotating, absolutely pressure-tight displacement system consisting of a self-sealing rotor and stator. The controlled rotary movement of the rotor generates the flow by displacing the medium in the stator. Pumping without changing the medium is guaranteed. As the material can also be conveyed backwards, preeflow® guarantees a clean, controlled material or medium tear-off without dripping. Application: - point dosing, with highest volumetric accuracy - bead application with application speed adjustable to the web speed - Potting technology

The piston filler is one of the main product of Npack, most of Npack liquid filling dispenser are applying in the fields of Daily chemicals, cosmetics, Food&beverage,personal care products, pharmaceuticals, Oils products.As piston filling machine are solely based on conventional volumetric technology, these are easy to operate and relatively low cost for the majority of the end-use industries. Piston filling machine is one of the most popular liquid filling machine for its universal ability ,piston filling machine can fill thick and highly viscous products, such as chunky, semi-paste, paste products, also extensively utilized to fill chemical preparations, such as adhesives, greases, epoxies, waxes, and lubricant oils, also an optional for filling thin liquid Widely application of liquids, such as viscous liquid, shampoo, lotion,cream;Food sauce;foamy liquid,hand liquid soap,detergent. High Performance and accuracy,easy operation.

GOONVEAN FIBERS provides a range of precision short cut fibres for use in adhesives, epoxy resins and sealants. These materials have a number of advantages such as reinforcement, fire resistance, flexibility and added strength. Among others PE, PP, PA, Cotton, Aramide etc. with a range of fiber length.

The GXR Static Mixer (Licensee of Bayer, AG) is used for mixing, dispersing and homogenization of viscous materials. It is a high performance motionless mixer design that creates a very high degree of mixing in a short length. It is capable of mixing materials with very large differences in viscosity and volumetric ratios. Mixing Capabilities Mix fluids with similar viscosity Mix high and low viscosity fluids (1 million : 1) Mix fluids with large differences in volumetric ratio (1,000 : 1) Disperse and mix polymers with blowing agents Thermal homogenization Viscosity homogenization Applications Two (2) component viscous materials such as Liquid Silicone Rubber (LSR), adhesives, polysulfide, sealants, epoxy resins, polyurethanes, etc. Plastics Injection Molding Plastics Extrusion Polymer manufacture and processing The mixing elements may be safely pressed out of the housing by pushing on the support ring which avoids any damage to the mixing grid The GXR mixing elements are presently also available in inexpensive plastic construction (50% glass-filled Nylon and polypropylene) Helical Static Mixer The HT helical static mixer pioneered the inline motionless mixing industry over 40 years. It is a cost effective static mixer design with moderate mixing performance capabilities. It is most suitable for use in small diameter turbulent flow and laminar flow applications where the mixing task is simple and where it’s characteristic features of low pressure drop and open geometric structure are best for the specific application. For difficult applications, the high performance GX static mixer is recommended for laminar flow applications. The Helical static mixer is available in metal and plastic construction in a wide variety of configurations and sizes.

The GX static mixer has been used successfully for the laminar flow mixing and/or dispersion of viscous fluids for over 35 years. It is a high performance static mixer capable of mixing materials with equal or very large differences in viscosity and volumetric ratio. Mixing is accomplished in a short length with a very high degree of mixing. Mixing Capabilities Mix fluids with similar viscosity Mix fluids with high and low viscosity (1 million : 1) Mix fluids with large differences in volumetric ratio (1,000 : 1) Disperse and mix polymers with blowing agents Thermal homogenization Viscosity homogenization Applications Polymer manufacture and processing. Two (2) component viscous materials such as Liquid Silicone Rubber (LSR), adhesives, polysulfide, sealants, epoxy resins, polyurethanes, etc. Plastics Extrusion Materials of Construction, Housings and End-Connections The GX static mixer can be supplied in most materials of construction, pipe/tube housings with virtually any end connection (Figure #13). GX-P mixing elements in 9.3 - 9.4mm outside diameter size are also available in plastic construction. History of GX Static Mixing Structure The GX static mixer was invented by Bayer AG of Leverkusen, Germany in the mid 1970’s. Bayer used the GX static mixer extensively in their polymer plants and subsequently licensed the design to Sulzer Chemtech of Winterthur, Switzerland who trademarked the design as the SMX* static mixer. Sulzer did a tremendous amount of fundamental high quality R&D work on the SMX structure and commercialized the SMX static mixer in tens-of-thousands of successful installations. The founders of StaMixCo held key technical and management positions in the Koch Engineering (the later Koch-Glitsch)-Sulzer Chemtech team that commercialized the SMX static mixer. Bayer licensed their 2nd generation of the SMX static mixer to StaMixCo which is branded as the GXR structure with integral support ring around the X-Grid mixing bars as described in a previous section of this web site. * StaMixCo is not a distributor of or affiliated with Sulzer Chemtech. SMX is a brand and trademark of Sulzer Chemtech.

Epoxy Resins are reactive intermediates used to produce a versatile class of thermosetting polymers. They are characterized by the presence of a three-membered cyclic ether group commonly referred to as an epoxy group, 1,2-epoxide, or oxirane. The most widely used epoxy resins are diglycidyl ethers of bisphenol A derived from bisphenol A and epichlorohydrin. The outstanding performance characteristics of the thermosets derived from bisphenol A epoxies are largely conveyed by the bisphenol A moiety (toughness, rigidity, and elevated temperature performance), the ether linkages (chemical resistance), and the hydroxyl and epoxy groups (adhesive agents). In addition to bisphenol A, other starting materials such as aliphatic glycols and both phenol and o-cresol novolacs are used to produce specialty resins.

EPX Primer is a unique two-component water-based epoxy adhesive primer. It is used as a deeply penetrating and quick-drying primer on metal, wooden and mineral substrates. EPX Primer has a very strong permanent adhesion and is UV resistant. Due to its rapid drying properties, it is easy to start with subsequent layers. Unlike many epoxy products, the product is ADR-free and therefore not considered dangerous goods for storage and transport.

DELO-DUOPOX are two part epoxy resin adhesives for bonding, casting and sealing of joints. Providing excellent adhesion to many materials, these two part epoxies are ideal in stressed or extreme conditions, including automotive and engineering applications. Two part epoxies are cold-cured, high-strength materials, which can be used where curing with heat is not an option. They cure when the two components are mixed together in the correct ratio. Product dependant, most versions are available in DELO-AUTOMIX cartridges, which present the two epoxy components (resin and hardener) in the correct ratio via a dispensing / mixing cannula. A wide range of curing properties are available, with rapid cure versions that are firm to touch in less than 10 minutes, to versions that are firm to touch in 8 hours. They offer high chemical resistance and are available in a wide range of viscosities. ** Click for more **

DELOMONOPOX epoxies are one part, heat cured epoxy resin adhesives for bonding, casting and sealing of joints. The epoxy resin adhesives are high strength materials that can be used as alternatives to riveting, welding and brazing in high stress applications. Epoxies exhibit excellent adhesion to metals, ferrites and ceramics. Special advantages of epoxies include their resistance to temperature, chemicals and low water absorption. They will also protect against corrosion. The epoxy resin is supplied ready to use with no mixing required. Curing occurs in 15-75 minutes @ 130-180 degrees C. Versions are available with good flow properties or with high run-off resistance. ** Click for more **

-a quality product -%50 pure animal bristle blended -epoxy adhesive is used -solvent-resistant -cleaned easily by thinner ergonomic wooden handle, comfortable feel and balance

-a quality product -Doesnt leave any bristle on the surface during application -%50 pure animal bristle blended -epoxy adhesive is used -solvent-resistant -cleaned easily by thinner ergonomic plastic handle, comfortable feel and balance

Hexcel manufactures a wide range of film adhesives, foaming films, primers and liquid shims for metal-to-metal and composite bonding. Redux® and HexBond™ Film Adhesives, Foaming Films, Primers and Liquid Shims Hexcel formulates and manufactures a comprehensive range of structural film adhesives, foaming adhesive films, paste adhesives, liquid shims and primers for aerospace and industrial markets. Redux® and HexBond™ Film Adhesives Epoxy and bismaleimide (BMI) adhesives are supplied in film form on a roll and require heat and pressure to cure. These high performance structural adhesives are ideal for metal to metal and composite bonding and for the manufacture of honeycomb sandwich structures. ** Click for more **

For every project, FIP INDUSTRIALE always supplies the adhesive with the most suitable characteristics to meet site requirements. The broad range of adhesives for gluing gaskets, guidance rods and load spreading pads includes single-component, single-coating adhesives and thixotropic epoxy adhesives serving both as glue and as levelling agent for the groove concrete surface. Gasket gluing tests on concrete.

This type of joint was specifically designed for highway use within structures creating horizontal movements up to 15 mm and vertical movements up to 5 mm. Due to its characteristics, it can be fitted on any type of structure, whether it is made of reinforced concrete, prestressed concrete or steel. It consists of: • a Hypalon gutter, ending at its extremes with a mesh securing it to the slab; • a neoprene ribbed bulb, of suitable section, resting onto its upper wings on the edges of the slab heads, recessed within the gap. The Hypalon gutter ensures watertightness of the deck and drainage of waters outside of the road bed. It is a seamless type of gutter and it covers the entire road bed with the right slope and it is fixed to the slab by means of a mesh with epoxy adhesive and primer.

 The function of the neoprene bulb is to support the overhanging pavement. JOINT TYPE HEIGHT H (mm) WIDTH *X (mm) GAP *Y (mm) Bulbo piccolo 43 45 Max 20 Bulbo medio 77 80 Max 40 Bulbo grande 90