Results for
Germany
EWS takes measures against vibrations in deep drilling procedures Deep drilling procedures with drilling rods with a long overhang are one of the most demanding tasks in cutting technologies. What influences vibration, what amplitudes does it create, what is the effect of superimposed vibration and when are uncontrollable resonances encountered? All these are questions that are difficult to answer using theory alone. These findings formed the basis for the new development of EWS Rigid. The objective was to create a drilling holder with a passive damping system to counteract the vibrations that are created. This involves using variable vibration dampers with linear degrees of freedom in a floating mounting inside the cutter carrier. The damper position is set using a radially mounted setscrew, which allows optimum vibration conditions to be created. The improvement in surface qualities of bores is significant, as is the increase in the service life of cutter tools.
Request for a quoteGermany
Alternative to the standard we also offer individual solutions: » Corrosion protection with black galvanised housing surfaces (up to 720 hours in a salt spray test - depending on the magnet material)
Request for a quoteGermany
Alternative to the standard we also offer individual solutions: » Corrosion protection with black galvanised housing surfaces (up to 720 hours in a salt spray test - depending on the magnet material)
Request for a quoteGermany
With the telescopic aerial probe, any gas traces that may be present can be better detected. This is particularly recommended in pedestrian zones. Due to the high suction power of the extraction system, the gas concentration in the ground is already very diluted. However gas may still be later detected - but not with the telecopic aerial probe. Depending on the requirements, the telescopic aerial probe can be clicked into place quickly.
Request for a quoteGermany
foldable carpet probe (carbon-fibre) 180mm diameter wheel. Bore-hole probe (carbon fibre). Bell-probe funnel for attachment. Telescopic aeriel probe. Instrument filter. Carry-strap. Carry-case. Charger not included. Gas detector not included
Request for a quoteGermany
The impact elements consist of three components that are connected to one another by hot vulcanization A special rubber compound with a hardness of 62 ° Shore A, which absorbs the falling energy A top layer made of high sliding UHMWPE and a thickness of 10 mm A vulcanized aluminum profile for easy installation of the beams Special bolts with M16x40 also available in M12
Request for a quoteGermany
The adapter pieces are made to order in accordance with your specifications.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
Germany
We constantly have a large supply of HM replacement segments and HM bars in stock and also manufacture spare parts which fit scrapers made by other producers. Production of special segments based on drawing possible construction possible in hard metal, HM ceramic and ceramic Spare parts for the following manufacturers also in stock Indutechnik, Schulmeistrat Industrie Technik, Masch, Belle Banne, Manuflex, Duroflex etc.
Request for a quoteGermany
For directional and non-directional bores, For pipe lengths up to 18 m, For bores up to 3 m beneath the ground water level, Maximum outer diameter of the bore hole up to 1400 mm, Maximum lengths up to 120 m, A variety of different bore heads, rock boring heads or in-hole-hammers are available, depending on the soil quality.
Request for a quoteGermany
high level of dust sealing at the location where material is fed onto the belt conveyor minimal wastage a buffer for the material falling onto the belt conveyor reduced cleaning costs increased conveyor belt service life increased operational safety simple assembly no welding necessary exchange of the adapter piece for existing conveyor rollers Measurements of the impact bars approx. 1240 x 100 x 75 (L x W x H) The impact bars can be fitted using the enclosed screws optimal alignment of the skirting rubber on the conveyor belt
Request for a quoteGermany
For optimal functioning of the wipers, the holes in the guide rails should be closed with plastic covers, which are included with every delivery. As a replacement, you can also order them individually.
Request for a quoteGermany
PEKI float valve series made of high quality hot pressed parts and precision turned parts, assembled with modern injection moulded parts and sealing elements made in Germany . Compact design with high filling capacity manufactured in brass, chem nickel-plated and stainless steel.
Request for a quoteGermany
clamping range 13.5 - 13,8 mm with compensation 250 bar, as per data sheet B1.485
Request for a quoteGermany
clamping range 11.0 - 11,3 mm with compensation 250 bar, as per data sheet B1.485
Request for a quoteGermany
clamping range 13.5 - 13,8 mm with centring function 250 bar, as per data sheet B1.485
Request for a quoteGermany
clamping range 11.0 - 11,3 mm with centring function 250 bar, as per data sheet B1.485
Request for a quoteGermany
clamping range 9.0 - 9,2 mm without centring 250 bar, as per data sheet B1.485
Request for a quoteGermany
clamping range 9.0 - 9,2 mm with compensation 250 bar, as per data sheet B1.485
Request for a quoteGermany
clamping range 6.6 - 6,8 mm with compensation 250 bar, as per data sheet B1.485
Request for a quoteResults for
Boring - Import exportNumber of results
110 ProductsCountries
Category