Pressure-control valves - Import export

Body and Cover : ASTM A-536 Cast Iron / Valve Inner Parts: Bronze ASTM B61 / Pilot Control Valve and System: Bronze ASTM B62 w / Stainless Steel 303 Inner parts / Valve diaphragm: Buna-N neoprene ** Connection Type: Flanged / Pressure :16-25 Bar / Working Temp.:+4ºC , + 80ºC *** Increases the system equipment life and save the water in tank which is used for unnecessary operations. These valves are used to reduce the pressure which is over the limits on the system. **** Application Areas: After hydraulic calculations, If any pressure adjustment is needed, pressure reducing valves are suitable.

Within the family of pressureregulating valves, a technical distinction is made between series of bypass valves, inline valves and threeway valves.

Alpeco is the UK distributor of OCV control valves. These valves can be found in Waterworks, Fire Protection, Irrigation, Industrial, Petroleum and Aviation fueling in nearly every country throughout the world. The range of models available is extensive and includes pump control valves, pressure relief and safety valves, high level shut-off valves and flow control valves.

Pressure / Vacuum control valves suitable for safeguarding containers during loading / unloading phases of powder, grain and fibre products

The ViscoMT-L 3 / 18 barrel emptying system offers a modern way of emptying containers.The connection with the ViscoTec VMP dispenser series for the removal of the medium offers the following advantages: - container sizes from approx. 50 l to 300 l - viscosities of approx. 80,000 - 2,000,000 mPas - very low shear stress of the medium - very low pressure load of the medium (max. 18 bar) - removal of materials loaded with fillers - no backflow within the sampling pump - electrical control of the pump with pressure control - valve-free pump system - no material pressure reducer necessary due to electronic pressure adjustment - very good residual emptying (less than 1% residue) - electronic "empty" and "almost empty" message Application: Removal of materials directly from the delivery container, e.g. silicones, adhesives, resins, greases, colour pastes, metal-filled pastes (Cu and Ni solder pastes, Al and Ag pastes) - supply of media to dispensers

The ViscoMT-XS hobbock emptying system offers a modern way of emptying containers.The following advantages result from the use of eccentric screw pumps for the removal of the medium: - container sizes from approx. 5 l to 50 l - viscosities of approx. 80,000 - 2,000,000 mPas - very low shear stress of the medium - very low pressure load of the medium (max. 18 bar) - Removal of media loaded with fillers - no backflow within the sampling pump - electrical control of the pump with pressure control - valve-free pump system - no material pressure reducer necessary due to electronic pressure adjustment - very good residual emptying (less than 1% residue) - electronic "empty" and "almost empty" message Application: - Removal of media directly from the delivery container, e.g. silicones, adhesives, resins, greases, colour pastes, metal-filled pastes (Cu and Ni solder pastes, Al and Ag pastes) - supply of media to dispensers - direct dosing as pulsation-free flow rate

The ViscoMT-XL drum emptying system offers a modern way of emptying containers. The following advantages result from the use of eccentric screw pumps for the removal of the medium: - container sizes from 50 l - viscosities of approx. 80,000 - 2,000,000 mPas - Bridge frame can be driven underneath with drums on pallets - very low shear stress of the medium - very low pressure load of the medium (max. 18 bar) - Removal of media loaded with fillers - no backflow within the sampling pump - electrical control of the pump with pressure control - valve-free pump system - no material pressure reducer necessary due to electronic pressure adjustment - very good residual emptying (less than 1% residue) - electronic "empty" and "almost empty" message Application: - Removal of media directly from the delivery container, e.g. silicones, adhesives, resins, greases, colour pastes, metal-filled pastes (Cu and Ni solder pastes, Al and Ag pastes) - supply of media to dispensers

The ViscoTreat-R preparation and feeding system ensures an even and reliable product supply. At the same time, the medium is optimally prepared for the production process by stirring and circulating. The use of the VRP dispenser series for the further transport of the medium offers the following advantages: optimal processing of viscosities up to 50,000 mPas very low shear stress of the medium very low pressure load of the medium (max. 18 bar) - Removal of media loaded with fillers - no backflow within the sampling pump - electrical control of the pump with pressure control - no air supply necessary - valve-free pump system - no material pressure reducer necessary due to electronic pressure adjustment - Stator material is adapted to the medium to be pumped Application: - Feeding and processing of medium to highly sensitive media, e.g.: Silicones, adhesives, resins, greases, colour pastes, metal-filled pastes

Our valves are manufactured in-house and matched to the characteristics and pressures of your application. Our valves are full lift safety valves and can be spring loaded or pilot operated. All our valves are supplied set to your required working pressure up to a maximum of 4,000 bar and flow rates up to 4,700 l/min. Two versions of spring-loaded safety valves, even ATEX compliant The simpler high pressure valves have a rotatable bypass connection to dispose of leaking fluid. Pilot operated valves require a block flange. Like all other KAMAT products, these are ATEX compliant and can be manufactured in special materials to suit the medium being pumped.

KAMAT unloading valves are the ideal solution for precise pressure control at fixed or varying volumes. A fast and smooth acting high pressure valve that redirects the flow of the conveyed medium when the desired pressure is reached on the discharge side. Smooth operation makes it a reliable partner for pressure testing pipelines and vessels in all conditions. Reliability is further enhanced by the addition of a surge valve, which is further protected by its own filter. This extra filter is important when solid particles are present in the fluid, such as when drilling mud is reinjected into a well. As well as being reliable, our valves are simple and versatile to control. They can be controlled mechanically, pneumatically, electrically or hydraulically, all with the option of remote control. Special materials can also be used to provide an ideal solution for the process industry.

High Pressure Control Valve is designed and developed for applications where the high pressure / drop liquid and high pressure / temperature gas/vapour to be handled. Our specially designed Velocity Control Trim, which is a multi turn / multistage velocity control trim, handles these severe/critical applications very effectively – eliminating cavitation & vibration, and reducing the noise to the acceptable levels.

We manufacture rough or fully machined cage and seat for pressure control valves & control valves in : • Austenitic stainless steel Alloys (CF8M, CF3M…) • Aluminium-Bronze (UNS C95500…) • Duplex and Super Duplex (CD4MCu, CD3MN…) • Nickel-based and high-alloys (CW-6MC, CU5MCuC, M-35-1 CW-12MW…) • Martensitic alloys (CA15, CA6NM…) • Other materials on request

A Steam Conditioning Valve / Combined PRDS Valve is the combination of pressure reduction and temperature reduction of superheated steam to fit process needs, protect downstream equipment or allow the use of less expensive materials or schedules for downstream piping. This is done with a pressure reducing valve and a spray water addition section either as separate units or a single device. Pressure reduction is carried out with a pressure reducing trim within the valve body, usually multi stage pressure reduction. The pressure is controlled by an upstream or downstream pressure controller, signaling the valve to modulate to maintain the pressure at the required set point.Temperature is controlled by adding water to the steam in such away that it will get fully evaporated in the steam, termed as desuperheatmg. These applications are normally considered to be some of the most severe services of any valves in a modem steam plant.

Analogue flow indicators for measuring the flow rate of fluids in mobile and industrial hydraulics. The SDMKR is designed with a loading valve for the strain test of the hydraulic system to facilitate precise control of the operating pressure. In addition, this product can also be subjected to a reverse flow direction (without flow rate determination). ▪ Suitable for Mineral Oil (Aluminium), HFC Fluids and Water (Brass) ▪ Designed for in-line installation ▪ Mechanical flow measurement ▪ Controlling working pressure with a pressure control valve (only SDMKR) ▪ Flow indication in l/min and GPM for Aluminium units, Brass units have flow indication for Water and Oil both in l/min ▪ Aluminium unit: Dual scale ▪ Brass unit: Single scale ▪ Thread to connect with pressure gauge (only SDM) Accuracy (at a kinematic viscosity of 28cSt): ▪ Flow: ±4 % FSD ▪ Temperature: ±2,5 °C / ±5 °F ▪ Pressure (only SDMKR): ±1.6 % FS* ▪ Temp. measuring range: +20 °C ... +110 °C / +55 °F ... +245 °F ▪...

STRAIGHTENING AND CUTTING MACHINE Model EvoCUT6012 The new Tecno Impianti straightening & cutting machines model EvoCUT are a concentrate of strength, technology and design. They are used for straightening and cutting of smooth wires made of mild steel, stainless steel, brass, copper, bronze etc.; for the latter ones, we have developed tooling with specific geometries and materials. The use of brushless servomotors and very high quality planetary gearboxes for the management of the axes ensure an excellent performance in dynamic, dimensional and quality terms on the finished product. Proportional valves for pressure control allow the operator to store the settings regarding pulling and position transducer for each single application, ensuring the constancy of the set values over the time.

There are hydraulic pressing clamps in the fixture equipment of system. The workpiece is both made spot welding by means of clamps and prevented distortion due to heat during welding. Separate control lever is used as to be put to rear of piston for each piston.Also there is a pressure relief valve on each control lever. Thanks to pressure relief valves the critical pressure is brought to the desired pressure and the compression of the material in desired strength may be achieved A lock valve is connected to each hydraulic cylinder after the tightening process and during the welding operation, the material is prevented from being retracted and opened due to heat input. Reverse deflexion may be done on the frame thanks to the control units in the clamp mechanisms. 1 inert gas arc welding machine will be used for spot welding process.( it will be supplied by the purchaser)

Ideal for use in refuse-derived fuel (RDF) incineration plants for the handling of materials such as wood chips, shredded plastic or tires, paper and cardboard scraps, pellets and/or fluff. Mainly used in cement, paper and industrial plants (high heat-value areas). Technical design Optimisation of crane load capacity thanks to its lightweight design which can hold maximum loads Both motor grab systems (MZG and MMGM) can be made fully automatic by attaching sensors MZG is ideal for use in tight spaces Lightweight design for high load capacity Size, measurements and grab suspension can be customised according to your needs Further advantages: see type MZG port and type MMGM (under “products/motor grab systems) Grab drive Vertical electrohydraulic drive unit with high-pressure pump Turn control or valve control

Flow control valves regulate the flow or pressure of a fluid. Control valves normally respond to signals generated by independent devices such as flow meters or temperature gauges. Alpeco stock a range of Perrett hydrovalves and is the UK distributor for OCV Control Valves, who are leaders in control valves, check valves and pressure relief valves. Our flow control valves can be used across a wide range of fluids from fuel, oil and lubricants to paints, chemicals, water and cement.

Main products: valve body, housing, gate for butterfly valves, ball trunnion bearing & ball for trunnion mounted ball valve, flange, seat for ball and butterfly valves, cage for pressure control valves,... Alloys: - bronze and brass - low allied and pure copper - aluminium bronze - aluminium - stainless steel - Ni-based and special alloys

The injector-glass-blasting cabin is operated by hand with a gun. A blast-collecting collector ensures a smooth blasting circuit within the system. With the help of roller rails, as well as through-slots (on the side and in the roof surface with special brushes against the penetration of dust), surface treatment of glass panes is easy. On the front side there is an easy-open loading door for radiating hollow glass bodies. A work grate and two shock-proof long-field lamps (for glare-free illumination of the blasting chamber) guarantee a smooth workflow. The foot switch as well as the drain cup on the blasting agent funnel, an attached control box with pressure reducing valve and pressure gauge, motor protection switch, on / off button, solenoid valve, control lights, switches for interior lighting, main switch, emergency stop switch and support control ensure uncomplicated operation.

-Hydraulic Mini power packs -Hydraulic pumps, -Hydraulic Motors, Orbit Motors -Hydraulic power units and various hydraulic systems -Solenoid, Pilot, Manuel operated hydraulic directional control valves -Hand Valves -Relief, pressure, reducing, speed control valves, check valves, throttle valves -Modular and plate designed valves -Control blocks and hydraulic switch -Hydraulic Cylinders -Oil Coolers #hydraulicsystems #hydrauliccylinders #minipowerpacks #GearPumps #HydraulicMotors #HandValves

Armas “PR” model pressure reducing control valve is the hydraulic control valve which reduces high upstream pressure value into desired lower pressure value by means of built-in pressure reducing pilot valves. Pressure reducer control valve controls downstream pressure value continuously and maintains it constant without being affected from flow rate and upstream pressure values. When no flow exists in the system, it is closer by itself automatically. When valve upstream pressure value decreases below adjusted downstream pressure value, it is opened fully by itself. Valve may be user in vertical and horizontal positions in the system.

The hightemperature sliding gate control valve type 8024 in reinforced GS3 design with integrated positioner is suitable for a wide range of process applications up to 530°C. Media such as steam, liquids, gases, etc. can be precisely controlled even in the hightemperature range. Digital positioner type 8049 Pneumatic and electropneumatic positioner type 8047 Positioner with integrated process controller type 8049 IPC Positioner type 8047 and type 8049 also in explosionproof version Positioner with mounting acc. to NAMUR standard Metal bellows Limit switch Position feedback Manual override Pilot valve . . .