Modules - Import export

ZLN miniature toothed belt axis based on the low-profile guide system drylin® N. System width 40mm, installation height 28mm. Ready-to-install system with stepper motors or BLDC/DC motors. Configure drylin SHT linear modules individually here: https://igus.eu/ddx

drylin® SHT-12 linear module, drylin® R hard-anodised aluminium shafts, Trapezoidal lead screw TR10x2 made of stainless steel with ball bearings, machined lead screw ends 6h9x17mm, quad blocks, aluminium shaft end support, stroke lengths in 250mm or 500mm. Configure drylin SHT linear modules individually here: https://igus.eu/ddx

drylin® SAW-1040 linear module, drylin® W aluminium profile, surface: hard-anodised, Trapezoidal lead screw TR10x2, machined lead screw end 69x15mm, guide carriage, aluminium shaft end support. Stroke length: 500mm, carriage length: 69mm, NEMA23 stepper motor with JST connector. Configure drylin SHT linear modules individually here: https://igus.eu/ddx

drylin® SLW-1040 linear module, drylin® W aluminium profile, surface: hard-anodised, ball bearing Trapezoidal lead screw TR10x2 made of stainless steel, lead screw end machined 6h9x17mm, guide carriage in 100mm length, shaft end support made of anodised aluminium. Configure drylin SHT linear modules individually here: https://igus.eu/ddx

The innovative recuperation module from CIC acts as an energy-saving valve and control module directly in the pneumatic circuit. Functionality : It is installed directly on the consumer - e.g. on the pneumatic cylinder or in the pneumatic control circuit. The recuperation valve with its integrated control electronics measures and regulates the air consumption and feeds used compressed air back into the working cycle for reuse. Advantages : Reduction of compressed air consumption by up to 80%. Increase in efficiency of the plant. Smart monitoring and diagnostics of the pneumatic system with numerous evaluation options and control in line with Industry 4.0. Detection of leaks and irregularities. Delivery for predictive maintenance data. Avoidance of downtimes. Simple control software and wireless transfer from PC.

SCHOCK has many years of expertise in the assembly and manufacture of complex assemblies. Our customers can therefore also purchase a finished assembly from SCHOCK instead of many individual components

drylin® ZLW-0630 basic toothed belt axis, basic version, feed rate 54mm/rev, aluminium profile, surface: hard-anodised, neoprene toothed belt in black, guide carriage length 60mm, shaft end support made of aluminium, alignment of drive pin on the right, stepper motor with stranded wire. Configure drylin SHT linear modules individually here: https://igus.eu/ddx

The drive technology online configurator gives you the right drive technology system after you enter your requirements. You also have the option of requesting or ordering motors and other accessories, such as the motor control system. - Fast and easy configuration - Optional accessories - Detailed parts list - Fast delivery

Consists of step motor, planetary gears and tensionable drive wheel, fully assembled.

Body and clamping pin oxidised. Contact faces hardened and ground. Note: The UNI lock 5-axis add-on modules are used for raising basic modules and mounting base. Depending on the clamping situation, optimum assembly height can be achieved using a combination of the basic module and add-on module.

Main body oxidised. Contact faces hardened and ground.

UNI lock double clamp modules are particularly suitable for the direct clamping of workpieces. Workpieces with complex geometry can be completely machined on 4 and 5 sides. UNI lock double clamp modules can be mounted in any position. The high clamping forces are generated by the integrated spring package. (the unit clamps while not pressurised). Clamping is released pneumatically. The following clamping forces are possible with the UNI lock clampng pin in conjunction with M10, M12, M16 fastening screws: Clamping force (M10) 35,000 N Clamping force (M12) 50,000 N Clamping force (M16) 75,000 N Supplied with: 1 double clamp module incl. 3x pneumatic connections.

Body steel. Cam levers cast aluminium. Version Body black oxidised. Tnut electro zincplated. Cam levers black powder coated. Note The clamp module is inserted into the Tslot from above and secured using the cam lever, no other tools required. Advantages The eccentric clamp modules can be used on conventional aluminium profile systems or on Tslot tables as stops, fasteners or clamps for components and workpieces.

Elastomer spider polyurethane Shore 98A. Coupling housing and clamping hub, aluminium. Expanding mandrel steel. Screws steel. Centring rings 1.4301 stainless steel. Version Coupling housing black anodised. Note The motor adapter set with elastomer dog coupling system (elastomer coupling with expanding mandrel) provides a simple and costeffective solution for connecting electric motors. Advantages of the elastomer dog coupling Hub with expanding mandrel can be mounted axially Playfree with vibration absorption Excellent retaining force Excellent concentric accuracy Short design Easy to assemble Can be mounted axially on spigot side Electrical insulation Nominal torque up to 30 Nm On request Larger hub bore D. Higher nominal torque.

Body, extruded aluminium section. Bearing housing and slide, aluminium. Profile guide rail and guide carriage, steel. Toothed belt, polyurethane with steel cord reinforcement. Version Body natural colour anodised Bearing housing and slide, black anodised. Tracks of the profile guide rail, inductively hardened and ground. Note Compact and flexible linear actuators with toothed belt drive. The body consists of a selfsupporting aluminium extruded section with integrated profile guide rail. This rail system is able to absorb highest forces from all directions, is lowwear, and is optimised for moving large masses. Slots are located on the outer sides of the aluminium profile, ensuring easy, reliable assembly and enabling accessories mounted. Proximity switches can be positioned and fastened in the upper Tslot. The aluminium profile is fully compatible with our standard I series profiles.

Body and flange plate EN AW5754. Guide shafts steel Version Body, hardcoated Flange plates, anodised. Guide shaft, hardened. Note Maintenancefree pneumatic linear modules with two precision steel shafts and ball guide bushing with wipers. Double acting cylinder drive. All fastening threads have threaded inserts. The as accessory available shock absorbers and proximity switches can be integrated (no protruding edges). Positive fit construction for hundred per cent reproducibility. Combinations in all sizes and stroke variants are feasible without adapter plates. Repeat accuracies of ±0.01 mm are possible. Specified loads apply by centred carriages. On request Available with locking cartridge as stroke deviation safeguard. Accessory See table for shock absorber, proximitiy switch and plug connector.

Injection moulded, straight teeth. Engagement angle 20°. Machined bore. Polyacetal, white. Polyketone, ivorytone. Note Polyacetal Standard material with high hardness grade and low coefficient of friction. Polyketone Material with significantly longer service life, higher power transmission and greater security against tooth breakage due to the extraordinarily high wear resistance and very good tribological properties. Can be used under water and other media. Injection moulded gear wheels may have internal manufacturerelated cavities. These may become visible during drilling or broaching. They do not impair the function. The torques specified in the tables relate exclusively to the toothing.

Milled toothing, straight teeth. Engagement angle 20°, bright. Note Up to 48 teeth with hub one side, from 50 teeth supplied as disc form. The spur gears have a centre bore or pilot hole (this can vary due to manufacturing methods). For this reason, the dimension D2 max. given in the table is the maximum diameter of the bore with which the spur gears are supplied. This pilot/centre bore can be amended by the customer to produce a reamed bore, reamed bore with keyway or a tapped hole. Alternatively, customers can also use bushes to reduce the bore diameter. Form A with hub Form B without hub

Cisco Network Components GLC-TE= GLC-TE original & new

Disposable wooden pallets in Euro module size for single use as load carriers.

Features: — High rigidity and compactness: With excellent rigidity and compactness, this module offers possibility for size optimization at given thrust requirements. — Lightweight, high velocity and high acceleration: The ironless linear motor combined with an aluminum slider gives low self load, which is ideal for high acceleration and high velocity applications. — Smooth motion: Using ironless linear motor as the actuator, CLS run smoothly even at low speeds without cogging force. — High precision: High-precision positioning is achieved using closed-loop control with optical encoder based feedback. Available precision grades include Normal (N), High (H), and customized Precision (P) for even more demanding applications. — Multiple sliders: CLS can accommodate multiple sliders on the same axis, each controlled separately.

Features: — Moving magnets. — Fixed cable. — Short stroke & high duty cycle. — Angled or straight connector.

Features: — Exceptional dustproof design: CLMS has special structural design to make the whole module dustproof. In adverse working environments, the module will perform well while there will not be any structural issue caused by bellows. — Exceptional compact design: CLMS has optimized the allocated space for linear motor, linear guide, and optical (magnetic) encoder to minimize the size under thrust. — High reliability: CLMS’s encoder is installed horizontally, thus prevents its position to be affected by external impact and retains system precision. — Customization: Standard CLMS comes with magnetic encoder for position feedback. We can also install optical encoder based on customer’s need for precision while retaining the same dimensions. Other customized designs such as multi-slider, X-Y and gantry systems are available as well.

An easy way to automate a variety of processes such as medical masks stock control. It will allow you to use all the benefits of video analytics without using the Internet, high-power servers and other additional equipment. Advantages: Can work without internet connection USB and IP cameras can be connected Voice announcement Detection of incorrectly worn masks Integration with various access control systems, turnstiles, etc. Integration with CCTV systems An IP camera is a digital video camera, with a feature of the transmission of a video stream in digital format using the IP protocol. USB camera - a digital video camera capable of capturing images in real time for further transmission via the Internet, connected to a personal computer via a USB port. The module is able to recognize: Medical masks Worker helmets Can learn to recognize many more Recognition probability up to 99% Up to 5 people in the frame at the same time Recognition at a distance of 0.3 to 1.

The MODULE K series is a scalable, redundant modular UPS system designed to provide cost effective high availability of energy for high density data centers and mission critical applications. Online double conversion UPS with advanced digital control. The modular architecture allows power and battery life to scale as demand or availability increases. Combination of modular design with N + X parallel redundancy technology. The maximum capacity of a single UPS is 625 kVA. The UPS can be operated in parallel to build a system up to 2500 kVA.

UPS IMPULSE MODULE series modular uninterruptible power supplies designed for sensitive equipment. The series has a compact design that provides a high power density in a single cabinet. Each model in this series is equipped with the latest 3level IGBT rectifier conversion technology and full DSP control technology, as well as hotswappable modules. This makes the UPS IMPULSE MODULE series the best combination of reliability and flexibility

An optional battery pack can be connected to the UPS to extend the available runtime. Up to four Battery Modules can be connected to one UPS.

An optional battery pack can be connected to the UPS to extend the available runtime. Up to four Battery Modules can be connected to one UPS

An optional battery pack can be connected to the UPS to extend the available runtime. Up to four Battery Modules can be connected to one UPS.