Special bearings - Import export

iglidur® JATM, metric d1 [mm]: iglidur® JATM/VATM consists of a hard-anodized ring and a bearing ring made of iglidur® J (JATM) and iglidur® V400 (VATM). These glide pairings fetch low coefficients of friction and high wear resistance - without lubrication. Special features Maintenance-free plain bearing system For high service performances High stiffening Simple installation Material: iglidur® J High temperature options VATM, iglidur® V400 More dimensions and supplies on request When to use it? When an axial bearing system with defined gliding partners is desired When extremely high wear resistance is required When a very low coefficient of friction is desired When not to use it? When an additional angle compensation is required igubal® axial bearing When little mounting space is available iglidur® J When only sporadic movements are present iglidur® G Y = wear [μm/km] Figure 36.1: The diagram shows the influence of load (p in MPa) and speed (v in m/s) on the wear of the axial bearing. Y= Coefficient of friction Figure 36.2: In the test with different speeds (v) and loads (p) the coefficients of friction of the bearing systems were determined (v in m/s, p in MPa). iglidur® JATM, metric d1 [mm]:

iglidur® flange bearing d1 [mm]: With this design it is possible to use the iglidur® high-performance bearings where housing bores with no precise tolerances are possible. When to use iglidur® flange bearings? When you want a screw flanged bearing When a clip bearing solution is not satisfactory as a sheet metal feedthrough When there is a housing with very rough tolerances When the tight fit of a press-fit bearing is not sufficient as an axial securing When not to use them? When an additional angle compensation is required igubal® flange bearing When a screw connection is not possible iglidur® clip bearing When a large guide length is necessary iglidur® G General features With this design it is possible to use the iglidur® high-performance bearings where housing bores with no precise tolerances are possible. The design enables high loads with minimum demand on the precision of the housing. iglidur® maintenance-free flange bearings are available in four materials - iglidur® G, iglidur® J, iglidur® X and iglidur® A180. Thus, with this design, a very wide range of applications - from the universal bearing through the highest wear resistance or temperature resistance (up to +250°C) up to FDA-compliant bearing solutions - can be covered. Installation Dependent on the stressing capacities, various mounting types are used. For low radial loads, it is enough to mount the iglidur® flange bearing with just two screws on a surface. For higher radial loads, it is advisable to support the iglidur® flange bearing in a bore on the reinforced side in the load direction. Large tolerances are permitted for this bore, as it is only to additionally support the iglidur® flange bearing. In order to support still higher radial loads, the iglidur® flange bearing can be press-fitted with the longer side in an H tolerance bore. The additional screw connection secures the firm seating of the bearing in the housing. For the mounting of the iglidur® maintenance-free flange bearing, no special tools or devices are necessary. The alignment of the bearing in multiple mounted shafts is easily possible at the installation. Available materials: iglidur® G, iglidur® A180, iglidur® J and iglidur® X The mounting of the iglidur® flange bearing: Simple and safe iglidur® flange bearing d1 [mm]:

MDM Double flange bearing b1 [mm]: When to use it? When the axial safety of the iglidur® clip bearing is not sufficient When there is a housing with very rough tolerance When high axial forces must be absorbed When not to use it? When an automated assembly is required iglidur® MKM When the iglidur® clip bearings offer adequate tightness iglidur® clip bearing When a large guide length is necessary iglidur® MKM MDM Double flange bearing b1 [mm]: Special features Large flange surfaces Symmetrical flange Easy installation Easy to clip on Undetachable after cataphoretic painting process Special option possible

Special features press fit Both sides axially mounted Tolerance compensation of the sheet thickness Easy installation Axially prestressed Special option possible MKM Double flange bearing d1 [mm]: Special features press fit Both sides axially mounted Tolerance compensation of the sheet thickness Easy installation Axially prestressed Special option possible Press in, flange, finished: loss secure, axially mounted When to use it? When a flanged bearing is needed When the housing bore is more than 4 mm long When the axial safety is not ensured by press fit When a two-side flange is required as a thrust surface When not to use it? When maximum compressive strengths are required iglidur® G When a simple press-in bearing is needed iglidur® M250 When a clip-on sheet metal feedthrough is sought iglidur® G MKM Double flange bearing d1 [mm]:

iglidur® L250: For fast rotations Bearings for fast rotary motions like, for instance, in fans and small motors. iglidur® L250 is available as cylindrical bearings and plain bearings with flange. specially developed for fast rotating applications Very low coefficients of friction Excellent wear resistance

igubal® spherical balls W..M/I Standard spherical ball - dimensional series K and E in metric and inch dimensions igubal® spherical balls W..M/I igubal® spherical balls R...M Low cost spherical ball - dimensional series K and E in metric dimensions igubal® spherical balls R...M igubal® spherical balls X...M Spherical ball for high temperatures - dimensional series K and E in metric dimensions igubal® spherical balls X...M igubal® spherical balls J...M, mm Spherical ball for low humidity absorption - dimensional series K and E in metric dimensions igubal® spherical balls J...M, mm igubal® spherical balls J...M, large dimensions, mm Spherical ball for low humidity absorption - dimensional series K in metric dimensions igubal® spherical balls J...M, large dimensions, mm igubal® spherical balls JKM-GT split, mm Splitted spherical ball for low moisture absorption - Dimensional series K in metric dimensions igubal® spherical balls JKM-GT split, mm igubal® spherical balls UWEM Spherical ball for underwater applications - dimensional series E in metric dimensions igubal® spherical balls UWEM igubal® clearance-free balls J4VEM, mm Clearance-free spherical balls through camber, dimensional series E igubal® clearance-free balls J4VEM, mm igubal® spherical balls J4...M, mm Low priced spherical ball - dimensional series K and E in metric dimensions igubal® spherical balls J4...M, mm igubal®-spherical balls RN248..M, mm Detectable spherical ball - dimensional series K and E in metric dimensions igubal®-spherical balls RN248..M, mm Every iglidur® material possesses a series of special properties which account for its suitability for certain applications and requirements. Currently we offer you spherical balls made of iglidur® materials W300 (standard), J, J4, R, UW and X. igubal® spherical bearings application examples Special properties: maintenance-free dry operation Corrosion resistant High compressive strength High elasticity Very low weight Various materials Spherical balls - material properties iglidur® W300 (Standard) – very wear-resistant material iglidur® R cost-efficient and low coefficients of friction iglidur® X resistant to temperature and chemicals iglidur® J low coefficients of friction and low humidity absorption iglidur® UW suited for underwater applications Tolerances Maintenance-free igubal® spherical balls are designed with a tolerance in the inner diameter according to E10. The shaft should have a tolerance between h6 and h9. When to use it? When maintenance-free materials are required When components of the dimensional series E and K should be used When different iglidur® materials should be tested When high compressive strength is required When high elasticity is required When not to use? When temperatures above +250°C prevail When dimensions over 50 mm are needed When rotation speeds in excess of 0,5 m/s should be implemented igubal® spherical balls W..M/I Standard spherical ball - dimensional series K and E in metric and inch dimensions igubal® spherical balls W..M/I igubal® spherical balls R...M Low cost spherical ball - dimensional series K and E in metric dimensions igubal® spherical balls R...M igubal® spherical balls X...M Spherical ball for high temperatures - dimensional series K and E in metric dimensions igubal® spherical balls X...M igubal® spherical balls J...M, mm Spherical ball for low humidity absorption - dimensional series K and E in metric dimensions igubal® spherical balls J...M, mm igubal® spherical balls J...M, large dimensions, mm Spherical ball for low humidity absorption - dimensional series K in metric dimensions igubal® spherical balls J...M, large dimensions, mm igubal® spherical balls JKM-GT split, mm Splitted spherical ball for low moisture absorption - Dimensional series K in metric dimensions igubal® spherical balls JKM-GT split, mm igubal® spherical balls UWEM Spherical ball for underwater applications - dimensional series E in metric dimensions igubal® spherical balls UWEM igubal® clearance-free balls J4VEM, mm Clearance-free spherical balls through camber, dimensional series E igubal® clearance-free balls J4VEM, mm igubal® spherical balls J4...M, mm Low priced spherical ball - dimensional series K and E in metric dimensions igubal® spherical balls J4...M, mm igubal®-spherical balls RN248..M, mm Detectable spherical ball - dimensional series K and E in metric dimensions igubal®-spherical balls RN248..M, mm

The mini clamp is characterised by its small size, positioning accuracy of the clamping arm, and lightweight construction. Mini clamps are fully self-locking. The clamping force is guaranteed even when the pressure is removed through the over dead-centre position of the toggle lever on the clamping arm. The permanent lubrication and special bearing bushings make the mini clamps maintenance-free. They can be operated using dry, oil-free air. The manual closing and locking using the hand lever. Pneumatic opening and closing. Attention: A 5/3-way valve is required, middle position vented. On request: Clamping arm without holes.

We supply from our existing stock Kalefeld elprom- aluminium flameproof motors / hazardous motors Ex de IIC T4 in frame size 56 - 132 ( 2- and 4- poles ) 0, 12 - 1 1 kW . All motors on stock are with Ptc thermistors and fixed bearing . Other frame sizes and versions are available within 4-5 weeks after receipt of order . Special applications Mechanical variants Protection IP56, IP65, IP66 Special flanges and shafts Without terminal box Uni-directional bearings, locked bearings or special bearings Terminal box on side SPM-vibrations measurement

RAEL, founded in Genoa in 1969 as a electric motors repair and rewinding company, has become an established name in project and production of electric motors for potentially explosive atmosphere. Since 1986 the company grew considerably and moved itself to Predosa where both production and offices are actually located. We supply from our existing stock Kalefeld RAEL- aluminium flameproof motors / hazardous motors Ex de IIC T4 in frame size 56 - 132 ( 2- and 4- poles ) 0, 12 - 1 1 kW . All motors on stock are with Ptc thermistors and fixed bearing . Other frame sizes and versions are available within 4-5 weeks after receipt of order . Special applications Mechanical variants Protection IP56, IP65, IP66 Special flanges and shafts Without terminal box Uni-directional bearings, locked bearings or special bearings Terminal box on side SPM-vibrations measurement

Cemp offers custom-made solutions. The main customers are the chemicals industry, pharmaceutical industry, power plants and minings. Further fields of application are the on-shore- and off-shore plants as well as the shipbuilding industry. The name Cemp stands everywhere for guaranteed security against explosion of dangerous dusts and gasses . We supply from our existing stock Kalefeld cemp- flameproof motors / hazardous motors Exd(de) IIC T4 in frame size 63, 2-poles up to frame size 160, 2-poles (0,18 – 18,5 kW) and frame size 63, 4-poles up to frame size 180, 4-poles (0,12 – 22 kW). All motors on stock are with Ptc thermistors. Other frame sizes and versions are available within 2 -8 weeks after receipt of order . Cemp Explosion Proof Motors / hazardous motors available in IE1 and IE2 High Efficiency Special applikations Mechanical variants Protection IP56, IP65, IP66 Special flanges and shafts Without terminal box Uni-directional bearings, locked bearings or special bearings SPM-vibrations measurement Electrical variants Special voltage and frequency Heaters Bimetallic thermal protection (NC, NO), thermistor (PTC), platinum resistor (PT100) Single-phase with permanent capacitor Single-phase with centrifugal switch Accessories Forced ventilation (IC416) Encoder 100 - 10000ppr Bearing sensor Breaks D.C. disk brake A.C. disk brake Hand release of brake Reverse braking function (braking when energized - frame size 63-100)

Adding some supplementary features to the basic bearing types, FIP INDUSTRIALE can also produce special bearings, suitable for targeted purposes. These are the main types: Negative load bearings Also known as "anti-lifting" or "double-acting" bearings. These devices are also capable of resisting vertical tension loads, commonly denominated "negative". Load measuring bearings They permit in-situ measuring of vertical loads acting on the bearings. Depending on the technology used, measurements can be made next to the bearing or remotely, at any time of the bearing life span. Bearings with dampers These are a combination of one multidirectional or unidirectional bearing with hysteretic and/or viscous dampers. They are also called "flat sliding isolators with dampers". Bearings with shock transmitters Sliding bearings coupled with shock transmitters. In case of sudden movements, for example seismic movements, the shock transmitters prevent the relative movements of the structural eleme

The structural bearings are restraining devices used in structures, bridges and buildings, in order to precisely convey loads and restrain set degrees of freedom of movement. The range of FIP INDUSTRIALE structural bearings includes: all the types made of steel all the types made of rubber In addition to traditional types, FIP INDUSTRIALE also makes special devices such as anti-lifting, load measuring bearings, bearings for incrementally launched bridges etc. TYPES: Pot bearings Reinforced elastomeric bearings Sferopol bearings Cylindrical hinge bearings Special bearings