OKS SPEZIALSCHMIERSTOFFE GMBH

Lubrication of valve seals, collars, O-rings, drives, piston rods and guides Lubrication of slides, slat-band and roller chains Lubrication of cutting knives as well as of needles and lifters of knitting machines Dismantling of rusted-in parts and removal of oil and greasy soiling Advantages and benefits NSF H1 registered Highly effective due to good creep properties Broad range of uses Displaces water Duolabel Clean the surfaces for optimal effect. Apply OKS 370 with a brush, drip oiler or by immersion or using a suitable automatic lubrication system locations to be lubricated. Spray on evenly OKS 371 spray. Avoid excesses. In as far as available, observe the machine manufacturer's instructions. Assess the lubrication frequency and quantity on the basis of the service conditions. Caution: Only mix with suitable lubricants.

Lubrication of highly stressed chains, joints or slideways at higher temperatures For conveying systems running beneath radiated heat, in baking and drying lines in the foodstuffs industry Dry lubrication at operating temperatures above 200°C The synthetic oil content evaporates odorlessly without leaving residues, while the solid lubricant content are left behind to carry out dry lubrication Advantages and benefits Highly suitable as a high-temperature lubricant Highly effective due to homogeneous distribution of the finest graphite throughout the oil Versatile application as a liquid lubricant under high temperature conditions Resistant to water, chemicals, fuels, lubricants, and hydraulic oils NSF H1 registered For best results, clean the surfaces. Best way is to clean mechanically first and then with OKS 2610 or OKS 2611 universal cleaner. With a brush, drip oiler or by immersion or using a suitable automatic lubrication system, apply a sufficient quantity

Drop lubrication of cutting tools at machining work on ferrous and non-ferrous metals, for example during drilling, thread cutting, sawing, milling, punching and nibbling Advantages and benefits Reduces friction and required force Permits high continuous load and higher cutting speeds Allows optimal cutting surfaces Extend tool lives through reduction in wear Neutral behaviour toward machine coatings Free of chlorine and heavy metals Low tendency to form oil mist OKS 390 is suitable for use with the OKS Airspray system Also available as spray version OKS 391Apply a sufficient quantity of OKS 390 to the tool or machining point using a brush, drip oiler or oil can. Spray on sufficiently OKS 391 spray. After use OKS 390 can be removed with OKS 2610/OKS 2611 universal cleaner. Caution: Check compatibility before using on non-ferrous metals.

Drop lubrication of cutting tools at machining work on ferrous and non-ferrous metals, for example during drilling, thread cutting, sawing, milling, punching and nibbling Advantages and benefits Reduces friction and required force Permits high continuous load and higher cutting speeds Allows optimal cutting surfaces Extend tool lives through reduction in wear Neutral behaviour toward machine coatings Free of chlorine and heavy metals Low tendency to form oil mist Apply a sufficient quantity of OKS 390 to the tool or machining point using a brush, drip oiler or oil can. Spray on sufficiently OKS 391 spray. After use OKS 390 can be removed with OKS 2610/OKS 2611 universal cleaner. Caution: Check compatibility before using on non-ferrous metals.

Lubrication of parts subject to high levels of stress such as plain, roller and rod-end bearings, spindles and guideways Advantages and benefits Highly suitable for high-stressed lubrication points Highly effective caused by optimal combination of components Saving of maintenance and lubrication costs by reducing downtimes and corrective maintenance Reduction of down times due to wearFor highest effectiveness, carefully clean the lubrication point, for example with OKS 2610 or OKS 2611 universal cleaner. Before filling for first time, remove anticorrosion agent. Fill bearing such that all functional surfaces are certain of being greased. Fill normal bearings up to about 1/3 of the free space inside the bearing. Low-speed bearings (DN value below 50 000) and their housings should be filled completely. The bearing and machine manufacturer´s instructions should be observed. Subsequent lubrication at the lubrication nipples by grease gun or by automatic lubrication system.

Lubrication of friction, rolling and pivoting bearings, splined shafts, knockout spindles and sliding surfaces of all kinds under normal loads and all sliding speeds common for grease lubrication Supports sealing of bearings and corrosion protection Advantages and benefits Highly effective due to optimum combination of components Good resistance to pressure and water Fewer downtimes and repairs as a result of reduced wearing Resistant to ageing and oxidationFor highest effectiveness, carefully clean the lubrication point, for example with OKS 2610/OKS 2611 universal cleaner. Before filling for first time, remove anti-corrosion agent. Fill the bearing such that all functional surfaces are certain of being greased. Fill normal bearings up to about 1/3 of the free space inside the bearing. Low-speed bearings (DN value < 50,000) and their housings should be filled completely. The bearing and machine manufacturer's instructions should be observed.

Lubrication of open toothing, friction and rolling bearings, threaded spindles, hinges, guides on windlasses, ship´s cranes, underwater devices, offshore components or in wet areas of the textile industry Corrosion protection of moving parts subject to seawater in coastal and marine areas or constant influence of water Advantages and benefits Excellently suited as a waterproof special grease above and under water Highly effective due to optimum wear and outstanding corrosion protection Economical due to combined protective effect Lubrication of open toothing, friction and rolling bearings, threaded spindles, hinges, guides on windlasses, ship´s cranes, underwater devices, offshore components or in wet areas of the textile industry Corrosion protection of moving parts subject to seawater in coastal and marine areas or constant influence of water Advantages and benefits Excellently suited as a waterproof special grease above and under water

Lubrication of friction, rolling and pivoting bearings, splined shafts, knockout spindles and sliding surfaces of all kinds under heavy loads and a broad temperature range, as well as all sliding speeds permissible for grease lubrication Advantages and benefits Modern grease with a wide range of applications Supports sealing of bearings Good corrosion protection Resistant to ageing and oxidation Good resistance to pressure and water Available in the 120 cm³ ChronoLube cartridge For optimum effect, carefully clean the lubricating point, for example with OKS 2610/OKS 2611 universal cleaner. Before filling for first time, remove anti-corrosion agent. Fill the bearing such that all functional surfaces are certain of being greased. Fill normal bearings up to about 1/3 of the free space inside the bearing. Low-speed bearings (DN value < 50,000) and their housings should be filled completely. The bearing and machine manufacturer's instructions should be observed. Subsequent lubrication

Grease lubrication of unsheltered parts subject to heavy loading and/or impacts, such as friction, rolling and pivoting bearings, splined shafts, knockout spindles, threaded spindles and sliding surfaces of all kinds For harsh operating conditions Advantages and benefits Excellently suited as a safety lubricating grease in mixed friction sector with especially good wear protection Effectively protects against corrosion Contains Mox-active to improve performance For best results clean the lubricating point carefully. Clean with solvents like OKS 2610/OKS 2611 Universal Cleaner. Remove the corrosion protection ahead of the initial filling. Fill the bearings in a way that all the functional surfaces for sure get the grease. Slow moving bearings(DN-value < 50,000) should be filled completely, normal moving bearings should be filled to 1/3 of the free inner housing space. Observe the instructions of the bearing or machine manufacturer. Relubrication with a grease gun on to the grease

For lubrication points of all kinds as slide ways, spindles, geared parts of the electronic, precision engineering and optical equipment, temporarily or permanently exposed to extreme low temperatures like in arctic climates or cold storages Roller bearing lubrication of high-speed bearings, e.g. spindle bearings, miniature or precision bearings in machine-tools or textile machines, measuring equipment, electric motors of control technology and precision mechanics Advantages and benefits Dynamic light noise proofed long-term lubrication grease Best use at arctic conditions and very high speed High efficiency through optimal formulation Multifunctional application beside the regular range of performance for greases Efficient through economical application No nameable change of consistency at low temperatures or high speeds and accordingly temperatures