Results for
Germany
Swivel jib crane 4551.035Swivel jib crane, galvanized or stainless, admissible load max. 350 kg, regulating capacity: 1400 - 2000 mm haacon concentrates on the business units General Lifting Technology, Commercial Vehicle Components and Lifting Systems in the B2B sector.
Request for a quoteGermany
All products manufactured by us can be equipped with the appropriate corrosion protection according to your wishes and specifications. Epoxy resin coatings Hotspray coatings Hard and soft rubber linings KTL or powder coatings ECTFE/Halar SÄKAPHEN® coatings Pickling and passivation for stainlesssteel applications For drinking water systems, we can of course also provide coating products approved by KTW and DVGW w120
Request for a quoteGermany
State-of-the-art technology and extensive knowledge in the processing of steel characterise our location in Bad Salzungen, Germany. For us, performance means a wide range of cold-rolled steels of the highest quality at competitive prices, flexibility and a high degree of readiness to deliver while adhering precisely to the specified chemical and mechanical values. Surface finishing by electrolytic galvanizing and/or subsequent customisation of your goods are possible for us. We offer all our customers spooled materials with volumes of over 200,000 metres of metal strip per spool. This further development means a considerable advantage for our customers. Personnel-intensive set-up times and machine downtimes are avoided.
Request for a quoteGermany
Cold rolled strip is used in a variety of applications. It meets high demands on forming behaviour, dimensional tolerances and surface finish, which offers our customers decisive advantages! HFP cold rolled strip is ideally suited for all stamping, bending, drawing and deep drawing purposes. From ball bearing housings to roll cutting and punching strips, hose clamps, headlight reflectors, electrical equipment, office supplies and tubes to safety parts of all kinds, a wide variety of components can be manufactured for various industries. DC 01, DC 03, DC 04 according to DIN EN 10139 / mild steel - St 37/ special grades on request Depending on the customer's requirements, we supply treatment states from LG to C690.
Request for a quoteGermany
We manufacture and deliver the complete range of simple carrier roller holders, e.g. for the lower belt roll and 2 or 3 part upper belt stations in all trough angles. We are happy to manufacture and deliver simple to complex upper belt steering stations. We offer you Let us know when you inquire whether we should offer the conveyor roller stations in a primed, painted, galvanized or special version.
Request for a quoteGermany
In addition to the product range of classic cold rolling mills, we can also offer our customers electrolytically galvanized strip. The zinc coating offers excellent corrosion protection: In cooperation with our customers, we have developed a product that solves the problem of zinc abrasion in the processing of galvanized strips - ZPL (Zinc Plus Paint). An organic coating system is applied immediately after electrolytic galvanizing. This results in a colourless, uniform, highly lubricious layer with a dry film thickness of 0.50 - 3.00 µm, which can of course also be supplied in any desired colour. ZPL offers the following advantages: Further improvement of corrosion protection Excellent sliding properties, preventing zinc abrasion in the tool Reduced tool wear Longer tool life Oil-free processing is made possible Coating and printable layer with "Anti Finger Print" properties
Request for a quoteGermany
Alternative to the standard we also offer individual solutions: » Corrosion protection with black galvanised housing surfaces (up to 720 hours in a salt spray test - depending on the magnet material)
Request for a quoteGermany
Alternative to the standard we also offer individual solutions: » Corrosion protection with black galvanised housing surfaces (up to 720 hours in a salt spray test - depending on the magnet material)
Request for a quoteGermany
Alternative to the standard we also offer individual solutions: » Corrosion protection with black galvanised housing surfaces (up to 720 hours in a salt spray test - depending on the magnet material)
Request for a quoteGermany
We supply from the productions and our stocks ; the galvanized flat steel that is hot-dipping of cold- rolled metal through a zinc bath where both surfaces are coated with layer of zinc applied in order to enhance material lifespan and prevent corrosion which will eventually occur on the material surfaces in the presence of water or air moisture. Hot Dip Galvanized Steel Coils and / or Sheets Cut From Coils, Zero Spangle, Chromated, Unoiled Acc. to EN 10346/EN 10143 Drawing Steel Grades; DX51D+Z, DX52D+Z, DX53D+Z, DX54D+Z, DX56D+Z Structural Steel Grades; S220 GD+Z, S250 GD+Z, S280 GD+Z, S320 GD+Z, S350 GD+Z.. Coating Thickness from 50 gr/m2 to 300 gr/m2 Thickness from 0,2 to 4 mm. “Please contact with our Sales Department for the current Stock Delivery Options for DX51D+Z275 Sheets/Coils”
Request for a quoteGermany
Alternative to the standard we also offer individual solutions: » Corrosion protection with black galvanised housing surfaces (up to 720 hours in a salt spray test - depending on the magnet material)
Request for a quoteGermany
Alternative to the standard we also offer individual solutions: » Corrosion protection with black galvanised housing surfaces (up to 720 hours in a salt spray test - depending on the magnet material)
Request for a quoteGermany
Alternative to the standard we also offer individual solutions: » Corrosion protection with black galvanised housing surfaces (up to 720 hours in a salt spray test - depending on the magnet material)
Request for a quoteGermany
Alternative to the standard we also offer individual solutions: » Corrosion protection with black galvanised housing surfaces (up to 720 hours in a salt spray test - depending on the magnet material)
Request for a quoteGermany
The above mentioned flat pot magnets are manufactured from standard parts according to DIN EN ISO 4017-8.8. Dimensions and tolerances depend on the current status of the standard. Hexagon screws are suitable for being tightened with an open-end spanner. This is a special advantage in comparison to our round flat pot magnets, which only can be screwed on by hand. The hexagon screws are available with different lengths corresponding to fixed standards. By this simplified production method they are quite economical resp. there is a cost benefit compared with the turned special parts.
Request for a quoteGermany
Alternative to the standard we also offer individual solutions: » Corrosion protection with black galvanised housing surfaces (up to 720 hours in a salt spray test - depending on the magnet material)
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
Germany
This involves a play-free electronic switching cam encoder (abbreviated to: NOCE) with a maximum of four galvanically separated switching outputs, which can be set by the customer and which are activated or deactivated depending on the relevant position of the drive shaft. A parameterisable multiturn absolute encoder with SSI interface plus the switching cam encoder printed circuit board with separate controller are integrated into the compact housing. The SSI interface can be preset, the code direction can be set and the switching outputs can be preset.
Request for a quoteGermany
This involves a play-free electronic switching cam encoder (abbreviated to: NOCI) with a maximum of four galvanically separated1) SIL2 switching outputs that can be set by the customer, and which are activated or deactivated depending on the respective position of the drive shaft. A parameterisable multiturn absolute encoder with incremental interface as well as the four switching outputs are integrated in the compact housing. The switching outputs can be preset. A special shaft design appropriate to the play-compensating measurement gear ZRS is available. The supply voltage, incremental signal and switching contacts are each galvanically separated from one another
Request for a quoteGermany
This involves a play-free electronic switching cam encoder (abbreviated to: NOCN) with two (At version 79 four) galvanically separated switching outputs (cams), which can be set by the customer and which are activated or deactivated depending on the relevant position of the drive shaft. An absolute mulitturn encoder with CANopen interface, adjustable parameters and an electronic switching cam module is realized in the compact housing. A separate controller unit monitors the function of the cams. The encoder's CANopen position signal and the switching outputs can be parameterised separately. The parameterisation (cam limits, resolution, measuring range a.s.o.) has to be verified to the NOCN via a checksum. This checksum can be calculated by a TWK program or the standard algorithm recommended by the CiA. After verification the device can be set operational.
Request for a quoteGermany
This involves a play-free electronic switching cam encoder (abbreviated to: NOCN) with a maximum of four galvanically separated switching outputs (cams), which can be set by the customer and which are activated or deactivated depending on the relevant position of the drive shaft. A parameterisable multiturn absolute encoder with CANopen interface plus the switching cam encoder printed circuit board with separate controller are integrated into the compact housing. The encoder's CANopen position signal and the switching outputs can be parameterised separately. Parameterisation is carried out via the relevant CANopen objects in accordance with the encoder profile according to CiA, DS 406, revision 4.01. The NOCN has a fault monitoring system which outputs a fault message via the CANopen bus (emergency message) on detection of a fault.
Request for a quoteGermany
This involves a play-free electronic switching cam encoder (abbreviated to: NOCE) with a maximum of four galvanically separated SIL2 switching outputs that can be set by the customer, and which are activated or deactivated depending on the respective position of the drive shaft. A parameterisable multiturn absolute encoder with SSI interface and the switching cam encoder PCB with separate controller are integrated in the compact housing. The SSI interface can be preset, the encoding direction is adjustable and the switching outputs can be preset. A special shaft design appropriate to the play-compensating measurement gear ZRS is available. The supply voltage, SSI signal and switching contacts are each galvanically separated from one another.
Request for a quoteGermany
wivel jib crane 4551.015Swivel jib crane, galvanized, admissible load max. 175 kg, regulating capacity 275- 775 mm haacon concentrates on the business units General Lifting Technology, Commercial Vehicle Components and Lifting Systems in the B2B sector.
Request for a quoteGermany
This involves a play-free electronic switching cam encoder (abbreviated to: NOCA) with a maximum of four galvanically separated switching outputs (cams), which can be set by the customer and which are activated or deactivated depending on the relevant position of the drive shaft. A parameterisable multiturn absolute encoder with analogue interface plus the switching cam encoder printed circuit board with separate controller are integrated into the compact housing. The analogue signal and switching outputs can be parameterised separately using multifunction pins (MFP and PRE) in the connector.
Request for a quoteResults for
Galvanizing - Import exportNumber of results
49 ProductsCountries
Company type
Category