FLAIG MAGNETSYSTEME GMBH & CO.KG

Permanent magnetic chucks type PMNEO-X are super strong compact chucks for heavy cutting. Parts from about 30x15x6mm are stretched with max. achievable holding forces. Good holding forces can be achieved even on rough surfaces. The chipboard is activated via a removable hex shifter. Structure: — Double neodymium magnet system, steel body — transverse pole pitch 11+4mm — Holding power 150 N / cm2 — Magnetic field height 10mm — Pole plate wearing limit 6mm Recommendation: Super Strong chuck for milling

NMS Precision Sine Tables with built PMNM chipboard impress with very good workmanship and precision. The sine table base is hardened to 60 HRC, burnished and precision ground. The angle is adjusted according the sine principle by using gauge blocks. Our NMS sine tables are used in the EDM, grinding and measuring in the highest precision. Technical Details: — Precision Sine Table with built fine pole chipboard — Holding power 100N/cm2 — Magnetic field height 5mm — Pole plate wearing limit 5mm — plane parallelism 0,005/100mm — Angular accuracy +-0.0013°/+-5sec.

Super lightweight aluminum body for direct installation of clamping elements. The PMNM UPC pallet is delivered completely ready fitted to fit the Erowa UPC clamping system with original Erowa elements. Optional with handles and/or link Gripper. is used to clamp small and medium-sized workpieces. It works without an external power supply and is activated manually via a changeover lever.

Plate-spreading-magnets are used for separating of stacked iron and steel sheets. The sheet separators are laterally grown from the sheet stack, they magnetize the sheets with the same poles, which repel them from each other. Plate-spreading-magnets apply both in automated systems where plates with vacuum or transshipped are magnetic, and the manual work, where the gripping sheet is greatly facilitated by their help. Our Plate-spreading-magnets consist of a reinforced magnet system, which is installed in a stable sheet steel housing.

Pneumatically actuated magnetic gripper type PNEUMAG are pneumatic switchable bi-stable magnetic systems. Air pressure is only needed for switching. The magnet system is permanent and thus keeps safe even with pressure drop. PNEUMAG magnetic grippers enable thin, perforated or textured sheet metal parts (from 0,5mm) take and safe to transport what they recommended specifically for use in automatic and semi-automatic feeding systems as well as slings for robot grippers. PNEUMAG is the alternative to vacuum conveying systems. They were tested on a metal sheet St37 with smooth and clean surface. Note that depending on the application a safety factor of 2 or 3 has to be included.

HAND-Demagnetizers be used for degaussing of large parts or workpieces, which cannot be done to the device for other reasons, for example, Injection molds, stamping tools, vices built, clamped tools, etc. This portable model can be used for a maximum of 10 minutes of continuous operation. It is equipped with a thermostat that switches it off when the maximum permitted temperature (60ºC) is reached; it can only be used again once the temperature has dropped. The device is moved by hand over the workpiece, as close as possible to the surface, but without touching it.

The HGF Handgausmeter is an easy to use precision instrument. The superfine 1mm probe magnetic flux densities can be measured extremely close to the magnetic pole and in very narrow air gaps. The HGF can be switched between AC and DC magnetic fields as well as between units Gaus and Tesla. At the edge of the display the pending polarity N/S is in the mode "DC magnetic fields" constantly displayed, the "peak indicator" facilitates the search for magnetic surfaces for example, in tracking down unwanted residual magnetism. The package includes in addition to the meter, the 1mm transversal probe and the batteries and a protective case and a protective cap for the probe. Thus, HGF is also suitable for use in the service industry. Our technicians use it for testing of heavy lifting magnets and clamping systems.

For lifting of ground parts, bulk material and for occasional sorting out of magnetizable parts. ERM are equipped with mounted switch and integrated rectifier, for direct connection to 230 V mains voltage. The field depth is approx. 80-120 mm. Not permitted for transporting solid workpieces in unprotected areas.

Permanent Magnetic Circular Chuck Type RM, with reinforced ceramic magnet system can be used for clamping bulky and heavy workpieces. The magnetic force is infinitely variable, in the surface incorporated centering grooves facilitate alignment of the workpiece. In the rake face, a center hole can be introduced. Structure: — Ceramic magnet system, Aluminum body, — Max Pole pitch 5+8mm — Holding power 140N/cm² — Magnetic field height 8mm — Pole plate wearing limit 8mm — Switch travel MAG-ENT-MAG 500° Recommendation: Super Strong circular chuck for turning, also for rough parts

EHG electromagnetic holding rods are used in fixture construction, for gripper systems and for a wide variety of tasks in mechanical engineering. EHG holding rods consist of a screwed, two-part system, are double-coated and sealed to IP 65. Max. Operating temperature 60°C Standard voltage 24,48,110V DC Protection class IP 53 ED 100%