MDM Double flange bearing b1 [mm]: When to use it? When the axial safety of the iglidur® clip bearing is not sufficient When there is a housing with very rough tolerance When high axial forces must be absorbed When not to use it? When an automated assembly is required iglidur® MKM When the iglidur® clip bearings offer adequate tightness iglidur® clip bearing When a large guide length is necessary iglidur® MKM MDM Double flange bearing b1 [mm]: Special features Large flange surfaces Symmetrical flange Easy installation Easy to clip on Undetachable after cataphoretic painting process Special option possible
IGUS® GMBH
Germany
drylin® Q Square linear guides Square section tube made of hard-anodized aluminum Torque resistant without 2nd guidance Tolerates moments up to 10 Nm drylin® Q square section tube drylin® Q - bearing housing, adjustable Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually drylin® Q - bearing housing drylin® Q - bearing housing, adjustable with hand clamp Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually With manual clamp drylin® Q - bearing housing with manual clamp drylin® Q - housing bearing Q20 enclosed, anodized aluminium housing short design or tandem housing Torque resistant without 2nd guidance drylin® housing bearing Q20 drylin® W - flange bearing Flange pillow block made of anodized aluminum Round flange (01 version), square flange (02 version Standard type or tandem housing Torque resistant without 2nd guidance drylin® W - flange bearing drylin® Q - housing bearing Q10 Solid polymer bearing made of iglidur® J Very light Tolerates moments up to 3 Nm Space saving drylin® Q - housing bearing Q10 drylin® Q - accessory Based on a torque resistant square guide with 7.5 mm edge lengths Hollow chamber for supply lines (media, compressed air,cable) drylin® Q - accessory drylin® Q - gripper axis Toothed, hard-coated and corrosion protected square-hollow profile Move loads up to 500 g at speeds of up to 0.7 m/s Bearing made of iglidur® J Drive: NEMA11 stepper motor with gear wheel drylin® Q - gripper axis Move linear torque resistant, completely lubrication-free. The drylin® Q linear construction kit offers the user maximum flexibility in the design Individual housing options such as solid plastic bearings and adjustable complete housings with and without manual clamp are available. Due to the hollow chamber design, the rugged hard-anodised aluminium profile is very light and is suitable for the simultaneous conducting of supply cables. The mounting options are highly variable, among others, using slot nuts; installation size 20 can also combined with all 20/20 aluminium construction profiles. 1. Profile made of hard-anodized aluminum 2. Main body of the carriage made of aluminum 3. Customized clearance adjustment 4. Cover made of solid plastic 5. Gliding elements in high-performance polymer iglidur® J serve as a guide bearing and guarantee optimum running properties drylin® Q Square linear guides Square section tube made of hard-anodized aluminum Torque resistant without 2nd guidance Tolerates moments up to 10 Nm drylin® Q square section tube drylin® Q - bearing housing, adjustable Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually drylin® Q - bearing housing drylin® Q - bearing housing, adjustable with hand clamp Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually With manual clamp drylin® Q - bearing housing with manual clamp drylin® Q - housing bearing Q20 enclosed, anodized aluminium housing short design or tandem housing Torque resistant without 2nd guidance drylin® housing bearing Q20 drylin® W - flange bearing Flange pillow block made of anodized aluminum Round flange (01 version), square flange (02 version Standard type or tandem housing Torque resistant without 2nd guidance drylin® W - flange bearing drylin® Q - housing bearing Q10 Solid polymer bearing made of iglidur® J Very light Tolerates moments up to 3 Nm Space saving drylin® Q - housing bearing Q10 drylin® Q - accessory Based on a torque resistant square guide with 7.5 mm edge lengths Hollow chamber for supply lines (media, compressed air,cable) drylin® Q - accessory drylin® Q - gripper axis Toothed, hard-coated and corrosion protected square-hollow profile Move loads up to 500 g at speeds of up to 0.7 m/s Bearing made of iglidur® J Drive: NEMA11 stepper motor with gear wheel drylin® Q - gripper axis
IGUS® GMBH
Germany
drylin® productfinder Productfinder for leadscrew modules, toothed belt axes and tube adjustments. drylin® productfinder SHT drive technology SLW/SHT cross slide Accessories SLW drive technology Ready-to-connect drive system for step motor SHT – the standard Solid design Three different installation sizes Various materials for shaft and spindle Maintenance-free and corrosion-resistant TR 10 x 2, TR 18 x 4, TR 24 x 5 DryLin® SHT - Standard SHT-PL "Preload" Prestressed trapezoidal nut, preload force: 50 N Manually and continuously adjustable radial clearance Tapered off spindle end enables operation by hand wheel or motor DryLin® SHT-PL "Preload" SHTC Compact High flexibility Ideal for 2 carriages Maintenance-free, self lubricating Adjustable bearing clearance DryLin® SHTC - Flexible SHTS High speed Pitch 10 x 12, 10 x 50, 18 x 100 Steep-threaded spindle High-Speed-solution Maintenance-free, self lubricating DryLin® SHTS - Fast SHT lift table with quick release Aluminum version For fast format adjustments Brake by interlocking included Freely selectable stroke lengths SHT lift table with quick release SHT ZB - Zero-backlash threaded nut in linear axis Lubricant- and maintenance-free High precision independent of load Self-adjusting Quiet Resistant to corrosion Zerobacklash-leadscrew nuts SHT-BB leadscrew module with ball-bearing mounted spindle Higher RPMs, increased precision Belt drive permits radial loads Constant torque Reduced axial clearance drylin® SHT linear table with ball bearing mounted lead screw SHT – HTX high temperature high temperature til +180°C Shaft and spindle made of stainless steel Bearing material iglidur® X Carriage and traverses made of anodised aluminum SHT-20-EWM-HTX til 180°C SHTC - HYD Hygienic Design Easy-to-rinse solution Bolted connections are easily accessible and generously designed for clearances Materials: Plastic and VA stainless steel DryLin® SHTC-HYD SHTP mini - small and low-priced Miniature version Very low weight Very low priced Corrossion-resistant Carriages and shaft end supports made of high-performance polymers DryLin® SHTP mini SHTP - Economical Solid polymer design Low weight Low priced Corrossion-resistant DryLin® SHTP - Economical SHTP leadscrew module with quick release lighter solid polymer model For fast format adjustments Brake by interlocking included Freely selectable stroke lengths SHTP lift table with quick release SLW - The compact one Flat and compact High torsional stability (stiffening) Completely supported Hard anodized aluminium rail DryLin® SLW - Compact SLWE – PL - preload Flat and compact High torsional stability (stiffening) Completely supported Hard anodized aluminium rail DryLin® SLWE-PL preload SLWE-BB ball-bearing Lower drive force Minimized clearance up to 1500 rev/min (according to length and load) Quiet operation – reduced vibration of the overall system SLWE-BB lift table with ball-bearing mounted spindle SLWS - compact with steep thread Pitch 8 x 15 mm Flat and compact High torsional stability (stiffening) Hard anodized aluminium rail DryLin® SLWS compact with steep thread SAW – linear modul Trapezoidal or high helix spindle Threaded drive spindle with ball bearing Rail extrusion with high profile form factor, extremely torsion resistant drylin® SAW - linear axis SLW-ES – stainless steel version Stainless steel version with corrosion-resistant steel components (1.42305, 1.4408 or 1.4571) Bearing material selectable DryLin® SLW - the compact - stainless steel version SLN – Low profile linear axis Small (installation height from 22 mm), light and flat for manual operation with hand wheel drylin® miniature linear axis SLN – Low profile linear axis with motor Small (installation height from 22 mm), light and flat motorized operation drylin® SLN low profile linear axis with motor SLW - cross slide Low cost cross slide solution for manual adjustments lubricant-free and corrosion resistant Maximum stroke length in XY tables 300 mm DryLin® SLW cross slide SLW - cross slide - stainless steel For manual adjustments Flat and compact All construction materials: VA and V4A stainless steel Resistant to chemicals and corrosion DryLin® SLW cross slide made of stainless steel SHT/SHT-PL - cross slide High precision, extreme stiffening and precise alignment through CNC production Available as standard and preload version Mounting of upper unit with right or left alignment possible DryLin® SHT/SHT-PL - cross slide Ready-to-connect SAW for step motor For your step motor Type NEMA-23 Threaded drive spindle, ball-bearing mounted Pitches 2 mm, 3 mm, 12 mm or 50 mm per rotation Compact design, low weight, high stability Ready-to-connect DryLin® linear units SHT accessories for motor connections Fast and easy coupling of your motor with the maintenance-free DryLin® linear units. Spacer, motor flange and coupling form a construction kit for the easy installation of your NEMA23. DryLin® linear unit: Kit for connecting motor Cursor Plastic analog display for the adjustment and direct reading of the carriage position. DryLin® SHT - Cursor Spindle clamp Shaft clamping flange to be mounted on the cursor for a clamping of the threaded spindle. DryLin® SHT - Spindle clamp Hand wheel Hand wheel to be mounted at the end of the threaded spindle. Various types of handles available. DryLin® SHT - hand wheel Adapter plate For cursor and/or spindle clamp. DryLin® SHT - Adapter plate V-drive The DryLin® SHT-WT angular drives offer maximum flexibility in positioning. DryLin® SHT V-drive Bracket kit DryLin® SHT-WS is the new angle kit for the SHT linear sliding tables range. DryLin® SHT-WS: all directions Flexshaft The ideal complement for drylin® leadscrew modules. drylin® Flexshaft Spindle support SLW-1040 Smart solution for long stroke lengths of the SLW linear modules SLW-1040 - quiet lead screw for strokes >750mm drylin® E – „E“ as in electric The consistant development of the toolbox and system concept of the lubrication-free drylin® drive technology. drylin® E – „E“ as in electric The drylin® product portfolio provides lubricant-free linear axles that are driven either by trapezoidal thread, steep thread or toothed belt. The user can choose a suitable individual solution from lightweight solid plastic units up to massive stainless steel solutions. In all systems, the stroke length is freely selectable and the drive implemented either via hand wheel or motor. 1 Main body made of stainless steel, aluminum, zinc or plastic 2 Lubrication-free through polymer bearings and polymer nuts 3 3 shaft materials 4 Carriages made of anodized aluminum or solid polymer 5 8 trapezoidal thread pitches 4 steep thread pitches 6 Spindle machining according to drawings or spindle pin Steel, stainless steel or aluminum spindles Position indicator, clamping and hand wheels available DryLin® SHT - Design and assessment, horizontal DryLin® SHT - Design and assessment, vertical DryLin® SHT - Product range Technical data Glider material: iglidur® J Shaft materials: Alu, hard andonized Cf53 stainless steel Spindle material: Steel Stainless steel Aluminum, hard-anodized When to use it? For format adjustments In extreme environments When a cost-effective, ready-to-install solution is desired When corrosion resistance is required When it should be low noise When not to use it? When high loads should move highly dynamically When positioning accuracy < 0.1 mm is necessary If high running performance is required in continuous operation drylin® productfinder Productfinder for leadscrew modules, toothed belt axes and tube adjustments. drylin® productfinder SHT drive technology SLW/SHT cross slide Accessories SLW drive technology Ready-to-connect drive system for step motor SHT – the standard Solid design Three different installation sizes Various materials for shaft and spindle Maintenance-free and corrosion-resistant TR 10 x 2, TR 18 x 4, TR 24 x 5 DryLin® SHT - Standard SHT-PL "Preload" Prestressed trapezoidal nut, preload force: 50 N Manually and continuously adjustable radial clearance Tapered off spindle end enables operation by hand wheel or motor DryLin® SHT-PL "Preload" SHTC Compact High flexibility Ideal for 2 carriages Maintenance-free, self lubricating Adjustable bearing clearance DryLin® SHTC - Flexible SHTS High speed Pitch 10 x 12, 10 x 50, 18 x 100 Steep-threaded spindle High-Speed-solution Maintenance-free, self lubricating DryLin® SHTS - Fast SHT lift table with quick release Aluminum version For fast format adjustments Brake by interlocking included Freely selectable stroke lengths SHT lift table with quick release SHT ZB - Zero-backlash threaded nut in linear axis Lubricant- and maintenance-free High precision independent of load Self-adjusting Quiet Resistant to corrosion Zerobacklash-leadscrew nuts SHT-BB leadscrew module with ball-bearing mounted spindle Higher RPMs, increased precision Belt drive permits radial loads Constant torque Reduced axial clearance drylin® SHT linear table with ball bearing mounted lead screw SHT – HTX high temperature high temperature til +180°C Shaft and spindle made of stainless steel Bearing material iglidur® X Carriage and traverses made of anodised aluminum SHT-20-EWM-HTX til 180°C SHTC - HYD Hygienic Design Easy-to-rinse solution Bolted connections are easily accessible and generously designed for clearances Materials: Plastic and VA stainless steel DryLin® SHTC-HYD SHTP mini - small and low-priced Miniature version Very low weight Very low priced Corrossion-resistant Carriages and shaft end supports made of high-performance polymers DryLin® SHTP mini SHTP - Economical Solid polymer design Low weight Low priced Corrossion-resistant DryLin® SHTP - Economical SHTP leadscrew module with quick release lighter solid polymer model For fast format adjustments Brake by interlocking included Freely selectable stroke lengths SHTP lift table with quick release SLW - The compact one Flat and compact High torsional stability (stiffening) Completely supported Hard anodized aluminium rail DryLin® SLW - Compact SLWE – PL - preload Flat and compact High torsional stability (stiffening) Completely supported Hard anodized aluminium rail DryLin® SLWE-PL preload SLWE-BB ball-bearing Lower drive force Minimized clearance up to 1500 rev/min (according to length and load) Quiet operation – reduced vibration of the overall system SLWE-BB lift table with ball-bearing mounted spindle SLWS - compact with steep thread Pitch 8 x 15 mm Flat and compact High torsional stability (stiffening) Hard anodized aluminium rail DryLin® SLWS compact with steep thread SAW – linear modul Trapezoidal or high helix spindle Threaded drive spindle with ball bearing Rail extrusion with high profile form factor, extremely torsion resistant drylin® SAW - linear axis SLW-ES – stainless steel version Stainless steel version with corrosion-resistant steel components (1.42305, 1.4408 or 1.4571) Bearing material selectable DryLin® SLW - the compact - stainless steel version SLN – Low profile linear axis Small (installation height from 22 mm), light and flat for manual operation with hand wheel drylin® miniature linear axis SLN – Low profile linear axis with motor Small (installation height from 22 mm), light and flat motorized operation drylin® SLN low profile linear axis with motor SLW - cross slide Low cost cross slide solution for manual adjustments lubricant-free and corrosion resistant Maximum stroke length in XY tables 300 mm DryLin® SLW cross slide SLW - cross slide - stainless steel For manual adjustments Flat and compact All construction materials: VA and V4A stainless steel Resistant to chemicals and corrosion DryLin® SLW cross slide made of stainless steel SHT/SHT-PL - cross slide High precision, extreme stiffening and precise alignment through CNC production Available as standard and preload version Mounting of upper unit with right or left alignment possible DryLin® SHT/SHT-PL - cross slide Ready-to-connect SAW for step motor For your step motor Type NEMA-23 Threaded drive spindle, ball-bearing mounted Pitches 2 mm, 3 mm, 12 mm or 50 mm per rotation Compact design, low weight, high stability Ready-to-connect DryLin® linear units SHT accessories for motor connections Fast and easy coupling of your motor with the maintenance-free DryLin® linear units. Spacer, motor flange and coupling form a construction kit for the easy installation of your NEMA23. DryLin® linear unit: Kit for connecting motor Cursor Plastic analog display for the adjustment and direct reading of the carriage position. DryLin® SHT - Cursor Spindle clamp Shaft clamping flange to be mounted on the cursor for a clamping of the threaded spindle. DryLin® SHT - Spindle clamp Hand wheel Hand wheel to be mounted at the end of the threaded spindle. Various types of handles available. DryLin® SHT - hand wheel Adapter plate For cursor and/or spindle clamp. DryLin® SHT - Adapter plate V-drive The DryLin® SHT-WT angular drives offer maximum flexibility in positioning. DryLin® SHT V-drive Bracket kit DryLin® SHT-WS is the new angle kit for the SHT linear sliding tables range. DryLin® SHT-WS: all directions Flexshaft The ideal complement for drylin® leadscrew modules. drylin® Flexshaft Spindle support SLW-1040 Smart solution for long stroke lengths of the SLW linear modules SLW-1040 - quiet lead screw for strokes >750mm drylin® E – „E“ as in electric The consistant development of the toolbox and system concept of the lubrication-free drylin® drive technology. drylin® E – „E“ as in electric
IGUS® GMBH
Germany
Special properties Deflection with grooved ball bearings Lubricant-free linear guide using polymer plain bearings Various carriage lengths Hard-anodized aluminum profile Polyurethane or neoprene toothed belts Basic type version 02 A lubricant-free linear guide is moved by a neoprene (black) toothed belt with fiber-glass reinforcement. The deflection shaft made of stainless steel square and high-performance polymer gear wheel is mounted with 2 grooved ball bearings each. The drive pin is a stainless steel square 6x6 mm. A plastic adapter for pin diameter 10 mm is included in the scope of supply. Standard type version 02 The similarly lubricant-free linear guide is moved by a polyurethane toothed belt (white) with steel cord. Deflection shaft and tooth rim - single-piece - are made of coated steel (stainless steel optional). The deflection shafts are mounted in 2 grooved ball bearings. DryLin® ZLW - Technical data DryLin® ZLW - Drive torque and load DryLin® ZLW - Toothed belt axis design ZLW-1660 The toothed belt axis drylin® ZLW-1660 is the ideal solution for many positioning functions. The overall height is only 72 mm. The stroke length can be chosen freely (max. 3,000 mm). Toothed belt axis ZLW-1660 ZLW-1040 The toothed belt axis DryLin®ZLW-1040 is the ideal solution for many positioning functions. The installation height is only 45 mm. The stroke length is freely selectable (max. 2000 millimeter) The carriage is available in 3 sizes. DryLin® ZLW-1040 ZLW-0630 The toothed belt axis DryLin®ZLW-0630 is the ideal solution for easy adjustment and positioning functions in restricted space conditions. The installation height is only 31 mm. The stroke length is freely selectable (max. 1000 millimeter) DryLin® ZLW-0630 ZAW-1040 cantilever axis For the ZAW-1040 cantilever axis, the drive unit is firmly mounted and only the profile and load are moved. The axis profile is made of hard-anodized aluminum. The product is absolutely lubricant-free and corrosion-resistant. It has low weight and is suited for high accelerations. DryLin® ZAW-1040 ZLW-1040-OD reverse toothed belt axis Toothed belt axis for quick reverse positioning, 100% free of maintenance and lubricants. Opposite drive linear actuator ZLW-0630-OD reverse toothed belt axis Toothed belt axis for quick reverse positioning, 100% free of maintenance and lubricants. ZLW-0630-OD toothed belt drive ZLW-1040 toothed belt axis - Specialists LT version for freezer applications down to -30 ℃; UW version for underwater use DryLin® ZLW: Belt drive for extreme conditions Fastening possibilities The DryLin® linear axis ZLW can be fastened in many ways. DryLin® ZLW - Mounting DryLin® E motors Overview DryLin® E motors and accessories. Fitting to DryLin® linear tables. drylin® E – „E“ as in electric ZLW – NEMA motor flange, standard and customized The motor flange can be fastened on the extreme shaft end support with four screws. ZLW motor flange Special properties Deflection with grooved ball bearings Lubricant-free linear guide using polymer plain bearings Various carriage lengths Hard-anodized aluminum profile Polyurethane or neoprene toothed belts Basic type version 02 A lubricant-free linear guide is moved by a neoprene (black) toothed belt with fiber-glass reinforcement. The deflection shaft made of stainless steel square and high-performance polymer gear wheel is mounted with 2 grooved ball bearings each. The drive pin is a stainless steel square 6x6 mm. A plastic adapter for pin diameter 10 mm is included in the scope of supply. Standard type version 02 The similarly lubricant-free linear guide is moved by a polyurethane toothed belt (white) with steel cord. Deflection shaft and tooth rim - single-piece - are made of coated steel (stainless steel optional). The deflection shafts are mounted in 2 grooved ball bearings. When to use it? Quick positioning of small loads Quiet running Slim structure Underwater application with UW belt Cost-effective solution as basic version Continuous operation When not to use it? When high loads should move highly dynamically When positioning accuracy < 0,1 mm is necessary
IGUS® GMBH
Germany
drylin® productfinder Productfinder for leadscrew modules, toothed belt axes and tube adjustments. drylin® productfinder drylin® SET EasyTube drylin® single tube guide for light duty motion control with interior lead screw. drylin® SET EasyTube drylin® easytube with flange drylin® SET easytube as flanged version for axial mounting drylin® easytube with flange drylin® SET EasyTube with scaling DryLin® SET EasyTube scaling, including lasered, rinse-resistant drylin® SET EasyTube with scaling drylin® SET easytube - pretensioned on one side The new carrier flange enables the horizontal and vertical installation of the EasyTube on one side. drylin® SET easytube - pretensioned on one side drylin® SET EasyTube - weight-optimized The weight-optimized carriage option of the SET-25 for all cost-sensitive adjustment movements. drylin® SET EasyTube - weight-optimized DryLin® SHT - Design and assessment, horizontal DryLin® SHT - Spindle clamp DryLin® SHT - Cursor DryLin® SHT - hand wheel A = Expansive accessories available B = stainless steel clamping rings, radial and axial bearings made from plain bearing polymers C = carriages, trapezoidal lead screw nuts and torque support made from lubricant-free plain bearing polymers D = guide tube made from anodized aluminum E = trapezoidal lead screw (interior) made from steel or stainless steel F = shaft end support made from rugged plastics, optionally also available in flanged versions drylin® productfinder Productfinder for leadscrew modules, toothed belt axes and tube adjustments. drylin® productfinder drylin® SET EasyTube drylin® single tube guide for light duty motion control with interior lead screw. drylin® SET EasyTube drylin® easytube with flange drylin® SET easytube as flanged version for axial mounting drylin® easytube with flange drylin® SET EasyTube with scaling DryLin® SET EasyTube scaling, including lasered, rinse-resistant drylin® SET EasyTube with scaling drylin® SET easytube - pretensioned on one side The new carrier flange enables the horizontal and vertical installation of the EasyTube on one side. drylin® SET easytube - pretensioned on one side drylin® SET EasyTube - weight-optimized The weight-optimized carriage option of the SET-25 for all cost-sensitive adjustment movements. drylin® SET EasyTube - weight-optimized DryLin® SHT - Design and assessment, horizontal DryLin® SHT - Spindle clamp DryLin® SHT - Cursor DryLin® SHT - hand wheel