Results for
Germany
Copper Cathode 1.purity 99.97%-99.99% 2.Weight of each sheet: 125kgs (+/- 1%) 3.Net weight of each pallet: 2mts (+/- 1%) 4.Min. weight in each container: 20mts approx. 5. Gross weight of each container: 22.20mts approx. 6. Dimensions: 914*914*12mm The quality of cathode copper: copper concentrate by electrolytic refining method or cathode copper produced by electrolytic deposition according to GB/T467-1997 the provisions of the cathode copper cathode copper by chemical composition can be divided into high purity cathode copper (Cu - CATH - 1) and the standard of cathode copper (Cu - CATH - 2) and two brand of cathode copper test methods: high purity cathode copper chemical composition of the arbitration analysis method according to GB/T13293-1991 chemical analysis method of high purity copper anode, standard copper cathode of the chemical composition of the arbitration analysis method according to GB/T5121-1996Specification of methods for chemical analysis of copper and copper alloy
Request for a quoteTurkey
Copper Strips are manufactured from highly conductive and thin thickness. They are windly used in automotive industry; radiators, cable industry, electronic and electrical industries; decorative components and Building industry: roofings.etc. Coper Strips are ideally used in applications where the salt content in the soil is very high, with a width of 5mm to 160mm, Thickness of 0,10mm to 10mm. Copper strips are produced, hot and cold rolling , by extruded OF busbars and they are accordıng with TS EN 1652, DIN EN 1652, DIN EN 13599 also EN 13601
Request for a quoteTurkey
We offer wide range of copper sheets that are made with accuracy to suit the client’s specification. We manufacture these copper sheets soft, hard and semi hard optionally for use in electrical industry, Roofing and for other applications.They are produced that Copper fluid is casting to the moulds and follows to the rolling machines, to be Copper sheets. They are according with TS EN 1652, DIN EN 13599. General Properties Material with minimum copper content 99.95%.
Request for a quoteUnited Kingdom
hemical Composition: Total concentration of all impurities ≤ 65ppm (typical value ≤ 25ppm). Copper obtained by the difference between 100% and total impurities. ELEMENT SPECIFIED TYPICAL Se < 1.0 ppm < 1.0 ppm Te < 1.0 ppm < 0.5 ppm Bi < 0.5 ppm 0.20 ppm Sb < 1.0 ppm < 1.0 ppm As < 3.0 ppm 1.2 ppm Pb < 1.0 ppm 0.3 ppm Fe < 5.0 ppm 2.8 ppm S < 10.0 ppm 4.5 ppm Ni < 5.0 ppm < 1.0 ppm Sn < 1.0 ppm < 0.5 ppm Ag < 12.0 ppm 8.0 ppm
Request for a quoteUnited Kingdom
1000Mt or more minimum order a month, 12 month contract, 17% less LME. Copper in Tanzania, requires Bank Instrument (sblc,dlc,lc,bg )
Request for a quoteUnited Kingdom
High quality copper sheet metal, typically Grade C106, (CW024A) Peal-able plastic coating to one side Worldwide delivery
Request for a quoteUnited Kingdom
High-purity copper wire scrap and cathodes (99.99%) readily available. We're a trusted EU supplier. Contact us now!
Request for a quoteTurkey
We offer wide range of copper sheets that are made with accuracy to suit the client’s specification. We manufacture these copper sheets soft, hard and semi hard optionally for use in electrical industry, Roofing and for other applications.They are produced that Copper fluid is casting to the moulds and follows to the rolling machines, to be Copper sheets. They are according with TS EN 1652, DIN EN 13599. General Properties Material with minimum copper content 99.95%. Width : 1000 mm Length : 2000 mm Thickness : 0.40 mm to 4 mm
Request for a quoteRomania
We provide laser cutting services for stainless steel or aluminium sheets and pipes. High precision and fast execution are ensured by high-performance equipment and the experience of the Profinox team! Our laser cutting services have a number of benefits: Versatility – the tool can be used for a wide range of materials, with Profinox providing laser cutting services for stainless steel, aluminium or copper sheets and pipes; The power used for the laser metal cutting process is lower; The laser cutting procedure involves minimal deformation; Low costs for laser cutting; No contact between the part and the tool; Enhanced surface quality; Minimal burrs: this advantage provided by the laser metal cutting process also eliminates the need for further machining; Possibility to create and obtain complex shapes. Furthermore, the laser cutting process is silent and fast, ensuring a high precision of +/- 0.1 mm. If you have materials exceeding the maximum
Request for a quoteChina
Product Name: Brass Strips Coil Foil for Decoration Application: Electronic, telecommunications Width: 3mm-1220mm Material: Brass Grade: Brass Coil Cu (Min): 64.0-68.0% Model Number: C2680,C2680,C2700.etc. Place of Origin: China Processing Service: Bending, Welding, Decoiling, Cutting, Punching Shape: Strip Coil Roll Temper: O, 1/4H, 1/2H, 3/4H, H, EH, SH Alloy brand: C2680, C2600, etc Standard: JIS ASTM DIN EN ISO Surface: Mill,Polish,Bright,Hair line,Brushed,etc. Package Type: Standard export seaworthy package,or as required. Payment term: T/T,L/C etc. Port of shipment:Xiamen,China Lead time:15-30days
Request for a quoteGermany
Copper Cathode 1.purity 99.97%-99.99% 2.Weight of each sheet: 125kgs (+/- 1%) 3.Net weight of each pallet: 2mts (+/- 1%) 4.Min. weight in each container: 20mts approx. 5. Gross weight of each container: 22.20mts approx. 6. Dimensions: 914*914*12mm The quality of cathode copper: copper concentrate by electrolytic refining method or cathode copper produced by electrolytic deposition according to GB/T467-1997 the provisions of the cathode copper cathode copper by chemical composition can be divided into high purity cathode copper (Cu - CATH - 1) and the standard of cathode copper (Cu - CATH - 2) and two brand of cathode copper test methods: high purity cathode copper chemical composition of the arbitration analysis method according to GB/T13293-1991 chemical analysis method of high purity copper anode, standard copper cathode of the chemical composition of the arbitration analysis method according to GB/T5121-1996Specification of methods for chemical analysis of copper and copper alloys
Request for a quoteGermany
Copper Cathode 1.purity 99.97%-99.99% 2.Weight of each sheet: 125kgs (+/- 1%) 3.Net weight of each pallet: 2mts (+/- 1%) 4.Min. weight in each container: 20mts approx. 5. Gross weight of each container: 22.20mts approx. 6. Dimensions: 914*914*12mm The quality of cathode copper: copper concentrate by electrolytic refining method or cathode copper produced by electrolytic deposition according to GB/T467-1997 the provisions of the cathode copper cathode copper by chemical composition can be divided into high purity cathode copper (Cu - CATH - 1) and the standard of cathode copper (Cu - CATH - 2) and two brand of cathode copper test methods: high purity cathode copper chemical composition of the arbitration analysis method according to GB/T13293-1991 chemical analysis method of high purity copper anode, standard copper cathode of the chemical composition of the arbitration analysis method according to GB/T5121-1996Specification of methods for chemical analysis of copper and copper alloys
Request for a quoteGermany
Copper Cathode 1.purity 99.97%-99.99% 2.Weight of each sheet: 125kgs (+/- 1%) 3.Net weight of each pallet: 2mts (+/- 1%) 4.Min. weight in each container: 20mts approx. 5. Gross weight of each container: 22.20mts approx. 6. Dimensions: 914*914*12mm The quality of cathode copper: copper concentrate by electrolytic refining method or cathode copper produced by electrolytic deposition according to GB/T467-1997 the provisions of the cathode copper cathode copper by chemical composition can be divided into high purity cathode copper (Cu - CATH - 1) and the standard of cathode copper (Cu - CATH - 2) and two brand of cathode copper test methods: high purity cathode copper chemical composition of the arbitration analysis method according to GB/T13293-1991 chemical analysis method of high purity copper anode, standard copper cathode of the chemical composition of the arbitration analysis method according to GB/T5121-1996Specification of methods for chemical analysis of copper and copper alloy
Request for a quoteChina
Grade: 1000-8000Series Temper: O-H112 Type: Plate, Aluminum circle Application: Reflective Sign Boards Width: 70mm~1600mm Surface Treatment: Coated Place of Origin: China Model Number: 1050,1060,1100,3003 7075 Alloy grade: 1000-8000series Thickness: 0.5mm-8.00mm Certification: ISO9001 SGS Standard: GB / T3880 ASTM B209 Supply Ability: 5000 Ton/Tons per Month Packaging Details: standard export packing Lead time:15-30days Port of shipment: Xiamen Payment term:T/T,L/C etc.
Request for a quoteGermany
we process thin sheets, heavy plate, wear-resistant sheet and plate. aluminium sheets, stainless steel sheets, copper sheets, brass sheets and much more, with formates from 3000 to 8000 mm (118" to 315"), with thickness 1 mm – 180 mm (0,039" to 7") welded sheet metal structures, aluminium constructions, industrial profiles
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
China
DBC ceramic substrate: Direct bonded copper (DBC) substrates are commonly used in power modules, because of their very good thermal conductivity. They are composed of a ceramic tile (commonly alumina) with a sheet of copper bonded to one or both sides by a high-temperature oxidation process (the copper and substrate are heated to a carefully controlled temperature in an atmosphere of nitrogen containing about 30 ppm of oxygen; under these conditions, a copper-oxygen eutectic forms which bonds successfully both to copper and the oxides used as substrates). The top copper layer can be preformed prior to firing or chemically etched using printed circuit board technology to form an electrical circuit, while the bottom copper layer is usually kept plain. The substrate is attached to a heat spreader by soldering the bottom copper layer to it. 1. Thickness of substrate can be thin: 0.25mm,0.28mm,0.45mm,0.5mm,0.635mm,1.0mm,1.5mm, 1.8mm,2.0mm 2.
Request for a quoteChina
The metal stamping service can be customized during the whole manufacturing process from the mold developing, designing to producing. Every demand from customers like metal stamping, punching, deep pumping and specific angle bending are measured and tested according to the measurement of metal materials then apply to each kind of metal. Features of our products: 1. Material: Steel, Stainless steel, Aluminum sheet, Copper etc. 2. Surface treatment: Zinc plated, Powder coating, Paint, Nickel plated etc. 3. Requirement: based on drawing and quantity. 4. Stamping equipment: 10-500T 5. Packing: we will offer you the standard package which includes plastic film, foam, carton and wooden box which is suitable for transporting 6. Delivery time: Within 20 days after receiving your 30% deposit
Request for a quoteSpain
BARE MATERIAL The strips must be clean and free of detrimental defects, which must be specified by agreement between the customer and the supplier when requesting the quote and in the order. Normally, a small residual layer of lubricant is left on cold-rolled products, which is authorised unless otherwise specified. ROUGHNESS EN 1654 This must be agreed between the customer and the supplier when requesting the quote and confirming the order. SURFACE CONDITION EN 13599 The strips must be clean and free of detrimental defects, which must be specified by agreement between the customer and the supplier in the request for quotes and in the order. Normally, a small residual layer of lubricant is left on cold-drawn products, and this is acceptable unless otherwise specified. Discolouration is acceptable, provided that it is not detrimental to the use of the product. TIN COATINGS Tin coatings for strips and copper strips and copper alloys: Electrolytic s/EN 14436 and Hot dip s/EN 13148
Request for a quoteSpain
BARE MATERIAL The strips must be clean and free of detrimental defects, which must be specified by agreement between the customer and the supplier when requesting the quote and in the order. Normally, a small residual layer of lubricant is left on cold-rolled products, which is authorised unless otherwise specified. ROUGHNESS EN 1654 This must be agreed between the customer and the supplier when requesting the quote and confirming the order. SURFACE CONDITION EN 13599 The strips must be clean and free of detrimental defects, which must be specified by agreement between the customer and the supplier in the request for quotes and in the order. Normally, a small residual layer of lubricant is left on cold-drawn products, and this is acceptable unless otherwise specified. Discolouration is acceptable, provided that it is not detrimental to the use of the product. TIN COATINGS Tin coatings for strips and copper strips and copper alloys: Electrolytic s/EN 14436 and Hot dip s/EN 13148
Request for a quoteSpain
BARE MATERIAL The strips must be clean and free of detrimental defects, which must be specified by agreement between the customer and the supplier when requesting the quote and in the order. Normally, a small residual layer of lubricant is left on cold-rolled products, which is authorised unless otherwise specified. ROUGHNESS EN 1654 This must be agreed between the customer and the supplier when requesting the quote and confirming the order. SURFACE CONDITION EN 13599 The strips must be clean and free of detrimental defects, which must be specified by agreement between the customer and the supplier in the request for quotes and in the order. Normally, a small residual layer of lubricant is left on cold-drawn products, and this is acceptable unless otherwise specified. Discolouration is acceptable, provided that it is not detrimental to the use of the product. TIN COATINGS Tin coatings for strips and copper strips and copper alloys: Electrolytic s/EN 14436 and Hot dip s/EN 13148
Request for a quoteSpain
BARE MATERIAL The strips must be clean and free of detrimental defects, which must be specified by agreement between the customer and the supplier when requesting the quote and in the order. Normally, a small residual layer of lubricant is left on cold-rolled products, which is authorised unless otherwise specified. ROUGHNESS EN 1654 This must be agreed between the customer and the supplier when requesting the quote and confirming the order. SURFACE CONDITION EN 13599 The strips must be clean and free of detrimental defects, which must be specified by agreement between the customer and the supplier in the request for quotes and in the order. Normally, a small residual layer of lubricant is left on cold-drawn products, and this is acceptable unless otherwise specified. Discolouration is acceptable, provided that it is not detrimental to the use of the product. TIN COATINGS Tin coatings for strips and copper strips and copper alloys: Electrolytic s/EN 14436 and Hot dip s/EN 13148
Request for a quoteSpain
BARE MATERIAL The strips must be clean and free of detrimental defects, which must be specified by agreement between the customer and the supplier when requesting the quote and in the order. Normally, a small residual layer of lubricant is left on cold-rolled products, which is authorised unless otherwise specified. ROUGHNESS EN 1654 This must be agreed between the customer and the supplier when requesting the quote and confirming the order. SURFACE CONDITION EN 13599 The strips must be clean and free of detrimental defects, which must be specified by agreement between the customer and the supplier in the request for quotes and in the order. Normally, a small residual layer of lubricant is left on cold-drawn products, and this is acceptable unless otherwise specified. Discolouration is acceptable, provided that it is not detrimental to the use of the product. TIN COATINGS Tin coatings for strips and copper strips and copper alloys: Electrolytic s/EN 14436 and Hot dip s/EN 13148
Request for a quoteSpain
BARE MATERIAL The strips must be clean and free of detrimental defects, which must be specified by agreement between the customer and the supplier when requesting the quote and in the order. Normally, a small residual layer of lubricant is left on cold-rolled products, which is authorised unless otherwise specified. ROUGHNESS EN 1654 This must be agreed between the customer and the supplier when requesting the quote and confirming the order. SURFACE CONDITION EN 13599 The strips must be clean and free of detrimental defects, which must be specified by agreement between the customer and the supplier in the request for quotes and in the order. Normally, a small residual layer of lubricant is left on cold-drawn products, and this is acceptable unless otherwise specified. Discolouration is acceptable, provided that it is not detrimental to the use of the product. TIN COATINGS Tin coatings for strips and copper strips and copper alloys: Electrolytic s/EN 14436 and Hot dip s/EN 13148
Request for a quoteSpain
BARE MATERIAL The strips must be clean and free of detrimental defects, which must be specified by agreement between the customer and the supplier when requesting the quote and in the order. Normally, a small residual layer of lubricant is left on cold-rolled products, which is authorised unless otherwise specified. ROUGHNESS EN 1654 This must be agreed between the customer and the supplier when requesting the quote and confirming the order. SURFACE CONDITION EN 13599 The strips must be clean and free of detrimental defects, which must be specified by agreement between the customer and the supplier in the request for quotes and in the order. Normally, a small residual layer of lubricant is left on cold-drawn products, and this is acceptable unless otherwise specified. Discolouration is acceptable, provided that it is not detrimental to the use of the product. TIN COATINGS Tin coatings for strips and copper strips and copper alloys: Electrolytic s/EN 14436 and Hot dip s/EN 13148
Request for a quoteCzech Rep.
Allow us to briefly introduce ourselves and at the same time offer the services of our company. we precisely manufacture sheet metal parts, cabinets, covers and control cabinets made of steel, aluminum or copper sheet up to a thickness of 3 mm we treat the surface with powder paints, galvanizing we describe the screen printing method we weld or press bolts, nuts, screws onto sheet metal we have exact connector tools for 100% visual quality we make various moldings, signs (e.g. grounding) or bridges for attaching cables assembly, pre-assembly, packaging we have our own trucking company TIG, MAG and laser beam welding - we produce in small and large series
Request for a quoteResults for
Copper sheets - Import exportNumber of results
51 ProductsCountries
Category