Gear wheels - Import export

Worm screw steel. Worm wheel CuZn37Mn3Al2PbSiS40. Version Worm screw with righthand pitch, casehardened HV 620 – 700, flanks and hole ground. Note for ordering Wheels/screws can only be combined to form a worm gear if they have the same centre distance and transmission ratio. Note A worm gear consists of a worm screw (shaft) and a worm wheel. Suitable for forming worm drives with a 90° shaft angle. A worm drive enables very large speed reduction ratios with a single stage. The toothing has the flank shape K. The engagement angle is 15°. The worm gears are prebored. The stated T2 output torques are the permissible output torques on the worm wheel. These apply for an input speed of 2800 rpm of the worm screw. The worm gears are suitable for continuous operation at high speeds and high torques. Attention 22500171002 Screw polished only. 22500172002 Worm wheel with helical gear toothing.

Consists of step motor, planetary gears and tensionable drive wheel, fully assembled.

drylin® Q Square linear guides Square section tube made of hard-anodized aluminum Torque resistant without 2nd guidance Tolerates moments up to 10 Nm drylin® Q square section tube drylin® Q - bearing housing, adjustable Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually drylin® Q - bearing housing drylin® Q - bearing housing, adjustable with hand clamp Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually With manual clamp drylin® Q - bearing housing with manual clamp drylin® Q - housing bearing Q20 enclosed, anodized aluminium housing short design or tandem housing Torque resistant without 2nd guidance drylin® housing bearing Q20 drylin® W - flange bearing Flange pillow block made of anodized aluminum Round flange (01 version), square flange (02 version Standard type or tandem housing Torque resistant without 2nd guidance drylin® W - flange bearing drylin® Q - housing bearing Q10 Solid polymer bearing made of iglidur® J Very light Tolerates moments up to 3 Nm Space saving drylin® Q - housing bearing Q10 drylin® Q - accessory Based on a torque resistant square guide with 7.5 mm edge lengths Hollow chamber for supply lines (media, compressed air,cable) drylin® Q - accessory drylin® Q - gripper axis Toothed, hard-coated and corrosion protected square-hollow profile Move loads up to 500 g at speeds of up to 0.7 m/s Bearing made of iglidur® J Drive: NEMA11 stepper motor with gear wheel drylin® Q - gripper axis Move linear torque resistant, completely lubrication-free. The drylin® Q linear construction kit offers the user maximum flexibility in the design Individual housing options such as solid plastic bearings and adjustable complete housings with and without manual clamp are available. Due to the hollow chamber design, the rugged hard-anodised aluminium profile is very light and is suitable for the simultaneous conducting of supply cables. The mounting options are highly variable, among others, using slot nuts; installation size 20 can also combined with all 20/20 aluminium construction profiles. 1. Profile made of hard-anodized aluminum 2. Main body of the carriage made of aluminum 3. Customized clearance adjustment 4. Cover made of solid plastic 5. Gliding elements in high-performance polymer iglidur® J serve as a guide bearing and guarantee optimum running properties drylin® Q Square linear guides Square section tube made of hard-anodized aluminum Torque resistant without 2nd guidance Tolerates moments up to 10 Nm drylin® Q square section tube drylin® Q - bearing housing, adjustable Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually drylin® Q - bearing housing drylin® Q - bearing housing, adjustable with hand clamp Carriage version for all unsupported solutions Force absorption from all directions Anti-rotation Clearance is continuously adjustable manually With manual clamp drylin® Q - bearing housing with manual clamp drylin® Q - housing bearing Q20 enclosed, anodized aluminium housing short design or tandem housing Torque resistant without 2nd guidance drylin® housing bearing Q20 drylin® W - flange bearing Flange pillow block made of anodized aluminum Round flange (01 version), square flange (02 version Standard type or tandem housing Torque resistant without 2nd guidance drylin® W - flange bearing drylin® Q - housing bearing Q10 Solid polymer bearing made of iglidur® J Very light Tolerates moments up to 3 Nm Space saving drylin® Q - housing bearing Q10 drylin® Q - accessory Based on a torque resistant square guide with 7.5 mm edge lengths Hollow chamber for supply lines (media, compressed air,cable) drylin® Q - accessory drylin® Q - gripper axis Toothed, hard-coated and corrosion protected square-hollow profile Move loads up to 500 g at speeds of up to 0.7 m/s Bearing made of iglidur® J Drive: NEMA11 stepper motor with gear wheel drylin® Q - gripper axis

Injection moulded, straight teeth. Engagement angle 20°. Machined bore. Polyacetal, white. Polyketone, ivorytone. Note Polyacetal Standard material with high hardness grade and low coefficient of friction. Polyketone Material with significantly longer service life, higher power transmission and greater security against tooth breakage due to the extraordinarily high wear resistance and very good tribological properties. Can be used under water and other media. Injection moulded gear wheels may have internal manufacturerelated cavities. These may become visible during drilling or broaching. They do not impair the function. The torques specified in the tables relate exclusively to the toothing.

Injection moulded, straight teeth. Engagement angle 20°. Axis angle = 90°. Machined bores from module 1.5. Polyacetal, white. Polyketone, ivory tone. Note Polyacetal Standard material with high hardness grade and low coefficient of friction. Polyketone Material with significantly longer service life, higher power transmission and greater security against tooth breakage due to the extraordinarily high wear resistance and very good tribological properties. Can be used under water and other media. Injection moulded gear wheels may have internal manufacturerelated cavities. These may become visible during drilling or broaching. They do not impair the function. Bevel gear wheels are supplied as single components. To obtain a pair of bevel gear wheels, please order the specified mating gear as well.

The cam-type limit switch is a device used to control the movement of industrial and construction machinery. Information is transmitted via the shaft actuating micro-switches. Standard range BFCN: Gear ratio from 7.5 to 550 Number of cams from 2 to 5 Maximum rotation speed: 500 rpm IP55 Range BFRS: Gear ratio from 10 to 200 Number of cams 2 or 4 Maximum rotational speed: 500 rpm IP55 Options for both ranges: potentiometer, gear wheels, couplings, mounting flange, various cams The micro-switches are either deflection type or with positive opening. The choice between different types of cams allows to modify the reaction curve of the limit switches. On request, specific versions: Up to 12 cams Protection IP66 / 67 /69K Integrated potentiometer or encoder ATEX zone 2 and 21