Steel balls - Import export

Shell, ballbearing steel. Cage, plastic. Balls, steel. Note With seals both ends. The linear ball bearing is secured using DIN 471 / 472 circlips. Application Suitable for applications where installation space is limited.

inch sizes The inch dimensions are finding their way into the range of xirodur® B180 polymer ball bearings! In combination with the PA cage and either glass or stainless steel balls, they offer a long service life and excellent value for money. They can be used in up to 80°C, are corrosion resistant and free from maintenance and lubricants. Nonmagnetic and washable Corrossion-resistant Predictable service life Lightweight Electrically insulating Application areas:Medical technology, plant construction, cleanroom technology, materials handling inch sizes The inch dimensions are finding their way into the range of xirodur® B180 polymer ball bearings! In combination with the PA cage and either glass or stainless steel balls, they offer a long service life and excellent value for money. They can be used in up to 80°C, are corrosion resistant and free from maintenance and lubricants. Nonmagnetic and washable Corrossion-resistant Predictable service life Lightweight Electrically insulating Application areas:Medical technology, plant construction, cleanroom technology, materials handling

drylin® SHT-12 linear module, drylin® R hard-anodised aluminium shafts, Trapezoidal lead screw TR10x2 made of stainless steel with ball bearings, machined lead screw ends 6h9x17mm, quad blocks, aluminium shaft end support, stroke lengths in 250mm or 500mm. Configure drylin SHT linear modules individually here: https://igus.eu/ddx

xiros® B180 FDA for the food sector B180 is already the most successful range in the xiros® family, reliable and inexpensive. Now this range becomes a low-cost solution for the food industry. All dimensions up to Ø 25 mm are also available from now on in the FDA-approved version. For this, it is enough to adapt the cage of the polymer ball bearing, as the rings are already made from FDA-compliant material. Now xirodur® B180 ball bearings with stainless steel balls can be used anywhere in the unpackaged food processing/handling area and where temperatures do not exceed 80°C. Raceways and cages made ​​of FDA approved plastics Lubricant- and maintenance-free Washable For temperatures up to 80℃ Application areas:Food and packaging technology, handling technology, medical technology, cleanroom sector. xiros® B180 FDA for the food sector B180 is already the most successful range in the xiros® family, reliable and inexpensive. Now this range becomes a low-cost solution for the food industry. All dimensions up to Ø 25 mm are also available from now on in the FDA-approved version. For this, it is enough to adapt the cage of the polymer ball bearing, as the rings are already made from FDA-compliant material. Now xirodur® B180 ball bearings with stainless steel balls can be used anywhere in the unpackaged food processing/handling area and where temperatures do not exceed 80°C. Raceways and cages made ​​of FDA approved plastics Lubricant- and maintenance-free Washable For temperatures up to 80℃ Application areas:Food and packaging technology, handling technology, medical technology, cleanroom sector.

xiros® polymer ball bearing – now electrically conductive xiros® F180 polymer ball bearings offer protection against electrostatic discharge. In this type with ESD protection (Electro Static Discharge), the newsly developed ball bearing material xirodur® F180 is used. The new development is applicable up to +80°C and offers a long service life. Free of lubrication and maintenance. Electrically conductive (ESD protection). economical Lightweight. Industries:Semiconductor industry, handling, paper, textile and glass industries, etc., furniture industry etc. d1 [mm]: xiros® material - Material data xiros® polymer ball bearing design, applications, development and testing xiros® chemical resistance xiros® F180 polymer ball bearings offer protection against electrostatic discharge. In this type with ESD protection (Electro Static Discharge), the newsly developed ball bearing material xirodur® F180 is used. The new development is applicable up to +80°C and offers a long service life. Free of lubrication and maintenance. Electrically conductive (ESD protection). economical Lightweight. Industries:Semiconductor industry, handling, paper, textile and glass industries, etc., furniture industry etc. PA-cage made of xirodur® F180, stainless steel balls -40°C to +80°C d1 [mm]:

Sleeve steel grade 5.8. Ball steel. Spring grade D steel wire.

Outer jacket stainless steel. Cage stainless steel. Balls stainless steel. Note The linear ball bearings correspond to series 3 of ISO 10285. With doublesided seals and a stainless steel cage. The bearing is secured with DIN 471/472 circlips. Linear ball bearings with doublesided seals should be greased before installation. The specified load ratings apply with the use of hardened and ground shafts.

Surfaces which are not flat and parallel can be firmly clamped or supported with with a flattened ball, the movable ball can adapt itself up to 9°. Longer versions have been designed especially to be glued in. This allows mechanical connecting elements with external thread to be made cost-effectively for small and medium-sized series. The ball has a rotation lock.

Ball lock pins are used for easy fastening or joining of components. The two balls are disengaged by pressing the push button and the pin can be slipped into holes in the workpieces. When the push button is released, the balls lock the connection securely. Shear force double shear (F) = S · τ aB max. The values given for the shear force are the theoretical breaking load. These are non-binding reference values without consideration of safety factors and exclude any liability. The values given are for information purposes only and do not constitute a legally binding assurance of properties. The load values have been calculated in accordance with DIN 50141. Each user must determine individually whether the ball lock pin is suitable for the respective application. Different materials in which the ball lock pins are used, weather conditions and wear can influence the determined values. Ball lock pins with high shear strength are identified by a groove marking on the pin.

Sleeve and spring stainless steel. Ball stainless steel or POM. Version: Sleeve bright. Steel ball hardened and bright.

The combination of excellent material properties is a special feature of silicon nitride (Si3N4). These include high resiliance and stability, excellent wear properties and good chemical resistance.

Steel housing. Nitrile rubber seal. Preloaded highaccuracy bearings with a 60° thrust angle. The bearings accept both radial and axial forces from both directions. Due to their preload, the angular contact ball bearings provide a high level of stiffness, excellent concentricity, precise tool positioning and repeatability. The integrated lowfriction seal effectively keeps dirt away from the bearing, thereby ensuring excellent operating safety and a long service life. The bearing friction coefficient Mrl is a reference value. The moment of inertia corresponds to that of the rotating inner ring. The limiting speeds are applicable after grease is applied. Technical data All bearings are supplied ready for mounting with lubricating grease type KE2P35 acc. to DIN 51825. Housing and shaft tolerances correspond to roundness tolerance class IT2 and perpendicularity tolerance class IT4.

Ball lock pins are used for easy fastening or joining of components. The two balls are disengaged by pressing the push button and the pin can be slipped into holes in the workpieces. When the push button is released, the balls lock the connection securely. Shear force double shear (F) = S · τ aB max. The values given for the shear force are the theoretical breaking load. These are non-binding reference values without consideration of safety factors and exclude any liability. The values given are for information purposes only and do not constitute a legally binding assurance of properties. The load values have been calculated in accordance with DIN 50141. Each user must determine individually whether the ball lock pin is suitable for the respective application. Different materials in which the ball lock pins are used, weather conditions and wear can influence the determined values.

Housing steel. Cage plastic. Balls steel. Note The linear ball bearings correspond to series 3 of ISO 10285. With doublesided seal. The linear ball bearings have a plastic cage which results in quiet and outstanding running properties. With flange for direct mounting on the housing. Linear ball bearings with doublesided seal should be greased before installation. The specified load ratings apply with the use of hardened and ground shafts. Precision guide shafts 21595. Fastening screws 07160.

Housing steel. Cage plastic. Balls steel. Note The linear ball bearings correspond to series 3 of ISO 10285. With doublesided seal. The linear ball bearings have a plastic cage which results in quiet and outstanding running properties. With flange for direct mounting on the housing. Linear ball bearings with doublesided seal should be greased before installation. The specified load ratings apply with the use of hardened and ground shafts. Precision guide shafts 21595. Fastening screws 07160.

Slides steel. Ball cages steel. Balls, steel. Version Slides electro zincplated. Ball cages, electro zincplated. Balls hardened. Note for ordering Sold in pairs. Note On telescopic slides with partial extension both sides, the travel is less than the installed length. Latches in open position on both sides. The dynamic load capacity of the telescopic slides indicates the maximum load rating of a vertically mounted slide pair when the entire extension length is used. The load capacity specified is calculated with a slide spacing of 450 mm and is based on the maximum value with 50,000 cycles. The load capacity is ca. 75% lower by horizontal mounting. The head height of the fastening screws should not exceed 2.5 mm otherwise there is a risk of collision with other parts of the slide. Advantages Pulls out in both directions Latches in open position on both sides Light running

Form C and F: Ball steel, ball seat high-carbon steel. Form G and J: Ball high-carbon steel, ball seat steel. Version: Form C and F: Ball hardened and black oxidised, ball seat phosphated. Form G and J: Ball phosphated, ball seat hardened and black oxidised. Note: The self-aligning pads serve as stops, rests and thrust pads in fixture construction. The seating face returns to the start position when the load is removed. Ball secured against rotation. Drawing reference: Form C: male thread, flattened ball, smooth Form F: male thread, flattened ball, diamond grip Form G: press fit, flattened ball, smooth Form J: press fit, flattened ball, diamond grip

Steel. Version: Ball thrust pins trivalent passivated. Ball seat and nuts electro zinc-plated. Note: Axial joint suitable for taking up tractive forces. The ball's movement can be controlled or fully locked in position using the clamping nut.

Body carbon steel. Balls roller bearing steel. Diverters plastic. Standard guide carriage with recirculating ball guidance precision N not preloaded (Z0). With doublesided end seal. 4row versions with round arch profile. The profile guide rail tracks are arranged at 45° and can accept loads from all directions. High dynamic values v = 5 m/s. Applicable temperature in continuous use max. 80 °C. On request Various precision and preload classes. Drawing reference 1) ground ref. edge

Slides stainless steel 1.4301. Ball cage stainless steel 1.4301. Balls stainless steel 1.4034. Version Slides bright. Ball cages bright. Balls bright. Note for ordering Sold in pairs. Note On telescopic slides with overextension, the travel is greater than the installed length. Latches in open position. When the release lever is actuated, the drawer can be taken out easily and separated from the guide. The dynamic load capacity of the telescopic slides indicates the maximum load rating of a vertically mounted slide pair when the entire extension length is used. The load capacity specified is calculated with a slide spacing of 400 mm and is based on the maximum value with 10,000 cycles. The load capacity is ca. 75% lower by horizontal mounting. The head height of the fastening screws should not exceed 2.5 mm otherwise there is a risk of collision with other parts of the slide.

Cam tool steel, hardened and black oxidised. Shaft carbon steel, hardened and black oxidised. Grip carbon steel, black oxidised. Ball knob black thermoset PF 31. Note: Admissible hand force for the handle. Accessory: Standard handles 06355. Screw-in handles with adjustable torque 06357.

Body carbon steel. Ball, ball bearing steel 1.2067. Form D: Ball with POM insert. Form H: Ball with POM insert. Form K: Ball with carbide insert. Form M has a carbide ball. Version: Body tempered and phosphated. Ball hardened. Form M ball nickel plated. Note: Self-aligning pads serve as stops, supports and thrust pads in fixture constructions. Ball secured against rotation. * Valid only if the minimum bore depth is observed. Drawing reference: Form C: with male thread, flattened ball, smooth. Form D: with male thread, flattened ball, with POM insert. Form F: with male thread, flattened ball, diamond grip. Form M: with male thread, flattened ball, with carbide insert. Form G: press fit, flattened ball, smooth. Form H: press fit, flattened ball, with POM insert. Form J: press fit, flattened ball, diamond grip. Form K: press fit, flattened ball, with carbide insert.

Sprocket steel. Ball bearing chrome steel. Screw and nut steel. Version Sprocket teeth hardened to HRC 50, electro zincplated. Ball bearing with sealing discs 2ZC3. Screw ISO 4017, grade 8.8, electro zincplated. Nut ISO 4035, grade 8, electro zincplated. Note For tensioning roller chains. The sprocket set can be combined with all tensioning elements to form a readytoinstall chain clamp. The ball bearings are sealed both sides, permanently lubricated and maintenancefree. The sprocket can be moved on the screw and thus adapted to the chain track. With the duplex and triplex version, precision spacer sleeves ensure correct chain guidance. Rigid mounting without a tensioning element is also possible. Can also be used as an idler sprocket.

Ball stainless steel. Housing steel. Cage polyamide, carbonfibre reinforced. These ball transfer units are matched to the aluminium profiles for roller rails and can be mounted on them quickly and easily. For flexible movements in two dimensions. With a lowwear and lowfriction ball rollers. No tools required. Suitable for aluminium profiles Type B and I.

Housing washer, shaft washer and rolling elements, bearing steel. Cage, steel. Note Axial ball bearings accept high axial loads from one direction but may not be loaded radially. The bearings are separable. This means the bearing parts can be fitted independently of each other. The main dimensions of the axial ball bearing conform to ISO 104 and DIN 711. Dimensional and running tolerances correspond to tolerance class PN acc. to DIN 620. These tolerance classes are standard and are well suited for most applications.

SKF High Viscosity, High Load and High Temperature Grease SKF LGHB 2 is a high viscosity mineral oil based grease using the very latest calcium sulfonate complex thickener technology. Due to its specific composition, the product can withstand high temperatures and extreme stress and can therefore be used for a whole range of applications, especially in mining and in the metal and cement segments. This grease contains no additives and the (EP) high pressure properties are due to the soap structure. • Excellent anti-oxidation and anti-corrosion properties • Good EP performance in high load applications • Withstands peak temperatures up to 200°C Typical Applications: • Steel-on-steel ball joint bearings • Pulp and paper machines • Asphalt vibrating screens • Continuous casting machines • Sealed spherical roller bearings with an operating temperature up to 150 °C • Roller bearings in the steel industry • Forklift mast rollers

All types of small objects can be retrieved by this tool, using the reverse circulation principle. It is especially useful to retrieve loose junk accumulated at the bottom of the hole. All junk is carried by the mud flow into the barrel and above the junk catcher. The tool is supplied with a short lifting plug, which includes a storage space for the steel ball. It is available in a wide range of sizes, with your choice of following options : - Single or double free-revolving junk catcher. - Internal fishing magnet. - Milling shoe

304 stainless steel tank Model SPABP1500 Pneumatic system Capacity 1500 L On welded feet Rounded bottom Atmospheric pressure Corked exterior finish Glossy annealed interior finish 1 drain with stainless steel ball valve outlet 40 MACON 1 Clear drawing with stainless steel ball valve outlet 40 MACON 1 stainless steel 316L floating cap and complete pneumatic system (stainless steel cover, pump, air chamber, valve) 3 welded feet (tank without level