Gas detector-controllers - Import export

Fixed gas detection system for oxygen, toxic and combustible gases This DIN – rail mounted modern control module saves space, money and installation time. One safe controller for all gases: Any combination of a sensor head plus control module is a complete gas detection system. This makes the Statox 501 so safe and reliable. The Statox 501 also gives you the opportunity to alter or expand existing systems with minimum cost and labor. Programs for all gases and measuring ranges are permanently stored in the memory of the controller. The user-friendly software program allows authorized personnel to select different configurations by a simple push of a button. Easy to install and easy to use The controll modules as well as the power supply and the common alarm module clip on to a DIN rail. The remote sensor heads and any alarm or recording devices connect to terminals on the front of the module. Each Statox 501 control module has three relays for alarm 1 and 2 and system failure (115 / 230 V AC / 2 A). An analog output for recorder or process control systems is also included. Measured values are displayed on a 4 digit LED-display. It is easy to program or calibrate the Statox 501! Just follow the menu! If intrinsically safe transmitters are to be installed in division 1 areas, they can be connected via intrinsically safe repeaters. 24 V power supply as well as the signals for the common alarm module are transmitted via bus from one module to the next. All terminals are easily accessible from the front. Field proven sensors for reliable gas detection Compur manufactures electrochemical sensors for the detection of oxygen deficiency and toxic gases. These sensors generate an electrical current proportional to the actual gas concentration. The remote sensor heads are designed as intrinsically safe certified 4 - 20 mA transmitters and have an integrated concentration display. Combustible gases can be detected with a variety of catalytic beads (pellistors) or infrared technology. The sensor heads are certified "Ex d" or "Ex de" and can be connected directly to the control module, even if they are to be used in classified areas. The control module can supply and operate different designs of catalytic sensors. With so many possibilities, the system can easily be tailored to suit your individual application needs. Easy maintenance saves time and money Maintenance of the 4 – 20 mA transmitters is very easy. A one-man calibration or replacement of the sensors can be done without further precautions, even in classified areas. Accessories A range of wall-mount cabinets for a maximum of 5, 8 or 32 controllers as well as a 19”-carrier, ensure an easy professional installation. -20 - +60 °C

With the GPD 3000 you can detect the smallest of leaks. The digital display enables the measured value to be recognized precisely and the analog display makes it easy to assess the trend. Leak detection is particularly problematic for seals with swellable materials. The leak detection sprays cause the sealing materials to swell and the leak is temporarily sealed again. The sensor in the GPD 3000 is protected from dirt and mechanical stress by a metal protective cap. o simple o light o exact o rugged o 30 year guarantee o includes a free annual revision Clear digital display of the measured values enables even inexperienced users to easily search for leaks. Together with the robust metal sensor head and the stable housing, the GPD 3000 is a professional leak detector for everyday work.

The GasPro gas detector can be equipped with sensors for up to five gases with ATEX approval. With the option of equipping the gas detector individually with various sensors, the GasPro gas detector is ideal for use in sewers, sewage treatment plants, landfills, ships, chemical and oil processing industries. An important unique novelty "positive safety" display. The GasPro signals the status at a glance via a three-color LED, green display = everything OK, yellow display = still OK, but a check is due soon, red display = not OK Particularly noteworthy is the loud alarm at 95 db and the optical signaling indicated by two LEDs that can be recognized from each side. The measured gas concentrations are saved every 10 seconds and stored in the internal memory. In addition, various events (switching on, alarm, calibration) are stored in the memory. The collected data can be transferred to a PC with a USB cable. A charging station with interface or a calibration station are also available.

Specially developed for the diverse tasks on the construction site, the Schütz Messtechnik company offers tailor-made measuring tools that reliably and comprehensively support the craftsman in all of his work “all around gas”. The complete solution for the load, leak tightness and usability test on gas pipes can be carried out safely and quickly, including documentation. GDPR-compliant as all personal data is protected against unauthorized access by a PIN. The measurement result can be printed out at the test point on site (optional), fully automatically and without interrupting the system. The professional solution for all measurements according to TRGI The prescribed load tests, tightness tests and usability tests, in the interior installation are possible with just one measuring device With integrated pump for pressure generation Very short measuring time through reference leak measurement PC software included

With the very simple operation and the generated and saved measurement protocol, the documentation can be created quickly and completely reproduced. It is possible to save the measurement data in the device and to print it out again later. No tracer gas nor a second measuring device are required for use. The internal battery, the 230V charger or the 12V vehicle voltage can be used for the energy supply. All included in a complete set. Ethane is always contained in natural gas; evidence of this gas is also evidence of natural gas. A lengthy gas analysis is normally required to prove beyond any doubt that the measured gas concentration is actually natural gas and not swamp gas. This, also due to the sampling, a difficult and time- consuming process, is completely eliminated. Measurement and sampling directly at the borehole is easily possible. The printout can take place after the measurement.

With the GPL 3000 you can detect the smallest of leaks. Leak detection is particularly problematic for seals with swellable materials. The leak detection sprays cause the sealing materials to swell and the leak is temporarily sealed again. The use of a gas detector is essential in this area. The sensor in the GPL 3000 is protected from dirt and mechanical stress by a metal protective cap. Clear display of the measured values makes it easy for inexperienced users to find leaks. Together with the robust metal sensor head and the stable casing, the GPL 3000 is a professional leak detector for everyday work.

With the GPL 3000 Ex you can detect the smallest of leaks. Leak detection is particularly problematic for seals with swellable materials. The leak detection sprays cause the sealing materials to swell and the leak is temporarily sealed again. The use of a gas detector is essential in this area. The sensor in the GPL 3000 Ex is protected from dirt and mechanical stress by a metal protective cap. Clear display of the measured values makes it easy for inexperienced users to find leaks. Together with the robust metal sensor head and the stable casing, the GPL 3000 Ex is a professional leak detector for everyday work.

With the GPD 3000 Ex you can detect the smallest of leaks. The digital display enables the measured value to be recognized precisely and the analog display makes it easy to assess the trend. Leak detection is particularly problematic for seals with swellable materials. The leak detection sprays cause the sealing materials to swell and the leak is temporarily sealed again. The sensor in the GPD 3000 Ex is protected from dirt and mechanical stress by a metal protective cap. o simple. Clear digital display of the measured values enables even inexperienced users to easily search for leaks. Together with the robust metal sensor head and the stable housing, the GPD 3000 Ex is a professional leak detector for everyday work.

In order to ensure that castings, valves, pumps, hoses and other components or groups have been manufactured free of leakage, they are tested in non-destructive leakage tests. Oxygen, air, nitrogen or sulfur hexafluoride (SF6) can be used as the test medium.

The INFRA.sens® was specially developed for high-quality NDIR gas analysis. In the design phase, special emphasis was placed on high stability and a low detection limit. With the use of high-performance light emitting diodes (IR-LED) and thermal micro radiators, which were adapted to the needs of gas measurement technology, these goals were achieved in full. In the spectral range from 2 μm to 12 μm, carbon dioxide, carbon monoxide, hydrocarbons and nitrous oxide can be reliably detected up to the ppm range with this new sensor platform. Applications Environmental and Process Measurement Technology (CEM) Engine development TOC analyzers Elemental analysis Industrial gas analysis Natural gas/biogas analysis Process measurement technology Biogas research