Mounting flange - Import export

iglidur® flange bearing d1 [mm]: With this design it is possible to use the iglidur® high-performance bearings where housing bores with no precise tolerances are possible. When to use iglidur® flange bearings? When you want a screw flanged bearing When a clip bearing solution is not satisfactory as a sheet metal feedthrough When there is a housing with very rough tolerances When the tight fit of a press-fit bearing is not sufficient as an axial securing When not to use them? When an additional angle compensation is required igubal® flange bearing When a screw connection is not possible iglidur® clip bearing When a large guide length is necessary iglidur® G General features With this design it is possible to use the iglidur® high-performance bearings where housing bores with no precise tolerances are possible. The design enables high loads with minimum demand on the precision of the housing. iglidur® maintenance-free flange bearings are available in four materials - iglidur® G, iglidur® J, iglidur® X and iglidur® A180. Thus, with this design, a very wide range of applications - from the universal bearing through the highest wear resistance or temperature resistance (up to +250°C) up to FDA-compliant bearing solutions - can be covered. Installation Dependent on the stressing capacities, various mounting types are used. For low radial loads, it is enough to mount the iglidur® flange bearing with just two screws on a surface. For higher radial loads, it is advisable to support the iglidur® flange bearing in a bore on the reinforced side in the load direction. Large tolerances are permitted for this bore, as it is only to additionally support the iglidur® flange bearing. In order to support still higher radial loads, the iglidur® flange bearing can be press-fitted with the longer side in an H tolerance bore. The additional screw connection secures the firm seating of the bearing in the housing. For the mounting of the iglidur® maintenance-free flange bearing, no special tools or devices are necessary. The alignment of the bearing in multiple mounted shafts is easily possible at the installation. Available materials: iglidur® G, iglidur® A180, iglidur® J and iglidur® X The mounting of the iglidur® flange bearing: Simple and safe iglidur® flange bearing d1 [mm]:

Other information IF -Design Award for Triflex®-Design Torsional movements possible Other information Installation instructions Joining, separating and filling of the Triflex®. Assembly Instructions Application examples Applications in various industrial sectors and in the igus® test laboratory. Triflex® 332.16 Inner height hi: 16 mm Inner width Bi: 16 mm Bending radii R: 38 - 100 mm Pitch: 13.3 mm E-Chain®. 332.32 Inner height hi: 32 mm Inner width Bi: 32 mm Bending radii R: 75 - 250 mm Pitch: 25 mm E-Chain®. 332.50 Inner height hi: 50 mm Inner width Bi: 50 mm Bending radii R: 100 - 250 mm Pitch: 30 mm E-Chain®. 332.75 Inner height hi: 75 mm Inner width Bi: 75 mm Bending radii R: 140 - 300 mm Pitch: 36 mm E-Chain®. 352.50 Inner height hi: 50 mm Inner width Bi: 50 mm Bending radii R: 10 - 250 mm Pitch: 30 mm E-Chain®, snap-open 333.16 Inner height hi: 16 mm Inner width Bi: 16 mm Bending radii R: 38 - 100 mm Pitch: 13.3 mm E-Chain®. 333.32 Inner height hi: 32 mm Inner width Bi: 32 mm Bending radii R: 75 - 250 mm Pitch: 25 mm E-Chain®. 333.50 Inner height hi: 50 mm Inner width Bi: 50 mm Bending radii R: 100 - 250 mm Pitch: 30 mm E-Chain®. 333.75 Inner height hi: 75 mm Inner width Bi: 75 mm Bending radii R: 140 - 300 mm Pitch: 36 mm E-Chain®. 353.50 Inner height hi: 50 mm Inner width Bi: 50 mm Bending radii R: 10 - 250 mm Pitch: 30 mm E-Chain®, snap-open This modular, rugged joint system is suitable for: Three-axis movements for machines of any type For dirt-filled environments High tensile strength Where rectangular shapes are requested Completely closed - reliable protection against dirt and chips Combination of different bending radii and axes Connection and separation possible at any chain Flanged mounting brackets or brackets, galvanized steel Snap-open Series 352 and 353 Combination of Series 353/333 possible Typical industrial sectors and applications Machine tools Robotics Material handling system Plastics industry Construction machinery Vehicle manufacturing Medical equipment IF -Design Award for Triflex®-Design Torsional movements possible

igubal® flange bearing EFOM With 2 mounting holes igubal® flange bearing EFOM igubal® flange bearing EFSM With 4 mounting holes, dimensional series E igubal® flange bearing EFSM igubal® flange bearing KFSM-GT With 4 mounting holes, dimensional series K igubal® flange bearing KFSM-GT igubal® flange bearing EFOM HT Applicable up to 200°C,resistant to chemicals , with 2 mounting holes igubal® flange bearing EFOM HT igubal® flange bearing EFSM HT Applicable up to 200°C,resistant to chemicals , with 4 mounting holes igubal® flange bearing EFSM HT igubal® flange bearing with ball pins, male thread igubal® flange bearing with ball pins - male threads for direct connections igubal® flange bearing with ball pins, male thread igubal® flange bearing with ball pins, female thread igubal® flange bearing with ball pins, female threads for direct connections igubal® flange bearing with ball pins, female thread igubal® flange bearings were developed for the bearing of shaft extensions or shaft bushings. Like all igubal® products, they consist of an igumid G housing and an iglidur® W300 spherical ball. igubal® flange bearings correspond to the dimensional series E and are offered with 2 or 4 mounting holes. Features igubal® flange bearings were developed for the bearing of shaft ends or shaft bushings. Like all igubal® products, it consists of a housing made of igumid G and a spherical ball in iglidur® W300. igubal® flange bearings correspond to the dimensional series E and are offered with 2 or 4 mounting holes. Application area As the igubal® flange bearings are also suitable for dry operation, they are particularly considered for applications in which the installation site is difficult, in humid or wet environment, or with special demands on hygiene. Thus the igubal® flange bearings are used for instance in wash-brush controls, in facade sunscreen systems, in materials handling systems and in bakery equipment. igubal® flange bearing - Applications Installation According to type, igubal® flange bearing are designed for mounting with 2 or 4 holes. The 2-hole types are provided with oblong holes that enable a trouble-free readjustment. A precise alignment of the bearing housing is not required as the flange bearing automatically compensates for error. Delivery program For shafts, igubal® flange bearings with 2 and 4 mounting holes are available in standard dimensions of 5 to 50 mm. For delivery times and more dimensions, you may please contact us. When to use it? When chemical resistance is required When a low-cost alternative is desired When dirt-resistant bearings are needed When misalignments should be compensated When fully split components are needed When not to use? When temperatures above +200°C prevail When an integrated collar is required When dimensions over 50 mm are needed When rotation speeds in excess of 0.5 m/s should be implemented igubal® flange bearing EFOM With 2 mounting holes igubal® flange bearing EFOM igubal® flange bearing EFSM With 4 mounting holes, dimensional series E igubal® flange bearing EFSM igubal® flange bearing KFSM-GT With 4 mounting holes, dimensional series K igubal® flange bearing KFSM-GT igubal® flange bearing EFOM HT Applicable up to 200°C,resistant to chemicals , with 2 mounting holes igubal® flange bearing EFOM HT igubal® flange bearing EFSM HT Applicable up to 200°C,resistant to chemicals , with 4 mounting holes igubal® flange bearing EFSM HT igubal® flange bearing with ball pins, male thread igubal® flange bearing with ball pins - male threads for direct connections igubal® flange bearing with ball pins, male thread igubal® flange bearing with ball pins, female thread igubal® flange bearing with ball pins, female threads for direct connections igubal® flange bearing with ball pins, female thread

Mounting plate steel/plastic. Monitor bracket aluminium. Bearing washers and sleeves plastic. Mounting flange aluminium. Mounting adapter aluminium. Screws steel. Version: Mounting plate painted. Monitor bracket painted. Mounting flange painted. Mounting adapter painted. Screws electro zinc-plated

Housing steel. Cage plastic. Balls steel. Note The linear ball bearings correspond to series 3 of ISO 10285. With doublesided seal. The linear ball bearings have a plastic cage which results in quiet and outstanding running properties. With flange for direct mounting on the housing. Linear ball bearings with doublesided seal should be greased before installation. The specified load ratings apply with the use of hardened and ground shafts. Precision guide shafts 21595. Fastening screws 07160.

Housing steel. Cage plastic. Balls steel. Note The linear ball bearings correspond to series 3 of ISO 10285. With doublesided seal. The linear ball bearings have a plastic cage which results in quiet and outstanding running properties. With flange for direct mounting on the housing. Linear ball bearings with doublesided seal should be greased before installation. The specified load ratings apply with the use of hardened and ground shafts. Precision guide shafts 21595. Fastening screws 07160.

Bearing flanges and fastening pieces PAGF. Bolts steel. Black. Bolts electro zincplated. Two bearing flanges combined with a D50 type I aluminium profile tube (10050) form a feed roller (loadbearing roller). The bearing flanges are simply pressed into the aluminium profile tube. These can be used for many conveyance tasks. The bearing flanges have ball bearings and springloaded fastening spigots which enable transport rollers to be retrofitted into existing structures. A roller conveyor is created when several transport rollers are mounted in series. Two bearing flanges are required for a transport roller.

The cam-type limit switch is a device used to control the movement of industrial and construction machinery. Information is transmitted via the shaft actuating micro-switches. Standard range BFCN: Gear ratio from 7.5 to 550 Number of cams from 2 to 5 Maximum rotation speed: 500 rpm IP55 Range BFRS: Gear ratio from 10 to 200 Number of cams 2 or 4 Maximum rotational speed: 500 rpm IP55 Options for both ranges: potentiometer, gear wheels, couplings, mounting flange, various cams The micro-switches are either deflection type or with positive opening. The choice between different types of cams allows to modify the reaction curve of the limit switches. On request, specific versions: Up to 12 cams Protection IP66 / 67 /69K Integrated potentiometer or encoder ATEX zone 2 and 21

Technical data Design Center body consists of 2 parts to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquids, drain water, sludge, food etc. (viscous media, pulverised media with fibre particles, plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (AISI 304) Stem Stainless steel 1.4305 (AISI 304) Hand wheel Steel, lacquered Pressure discharge bidirectional Stem Not rising Pressure range Please refer to the data sheet Temperature range • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Lever Steel, lacquered Pressure discharge One-sided Stem Not rising Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body Stainless steel 1.4408 Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4401 (316) Stem Stainless steel 1.4404 (316) Lever Steel, lacquered Pressure discharge One-sided Stem Not rising Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Function Pneumatic double acting Pressure discharge One-sided Pilot pressure 6bar (lower pressure on request) Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body Stainless steel 1.4408 Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4401 (316) Stem Stainless steel 1.4404 (316) Function Pneumatic double acting Pressure discharge One-sided Pilot pressure 6bar (lower pressure on request) Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 2 parts to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquids, drain water, sludge, food etc. (viscous media, pulverised media with fibre particles, plastic granulates, sand or similar media on request). Not suitable for steam. Refer to the advices on page 9 and 11! Body GG-25 (grey cast iron), epoxy coated 120 … 180µm (heattreatment 190°C, 20min) Sealing • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (AISI 304) Stem Stainless steel 1.4305 (AISI 304) Function Pneumatic single acting with spring return, normally closed (NC). Pressure discharge bidirectional Pilot pressure 6bar Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the table Temperature range • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Refer to the advices on page 8! Body Stainless steel 1.4408 Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4401 (316) Stem Stainless steel 1.4404 (316) Function Pneumatic single acting with spring return, normally closed (NC). Pressure discharge One-sided Pilot pressure 6bar Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the table Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 Installation Only with vertical upwards actuator The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy-coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Function Electric acting Pressure discharge One-sided Voltage 400V 3AC (24V DC, 230V AC on request) Pressure range Please refer to the table Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Dual plate check valves to be mounted between tow flanges according to EN 1092-1 Type 11 form B – PN10/PN16. Face to face EN 558-1 row 16 Connection DN50 … DN300 Mounting position Pay attention to the flow direction. Preferably mounting into a horizontal runing pipeline. Make sure to install a minimum of 5 x nominal diameter of straight pipeline in front of and behind the dual plate check valve. Do not install the valves directly onto a pump flange. Pressure range PN10 … PN16, see table Temperatur range 0°C … +80°C Media Non aggressive liquids Material Body: GGG-50, FBE-coated Flap: Stainless steel 1.4408 Stem and spring: Stainless steel 1.4401 Seals: EPDM The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice!

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body Stainless steel 1.4408. Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4401 (316) Stem Stainless steel 1.4404 (316) Function Electric acting Pressure discharge One-sided Voltage 400V 3AC (24V DC, 230V AC on request) Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 2 parts to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquids, drain water, sludge, food etc. (viscous media, pulverised media with fibre particles, plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (AISI 304) Stem Stainless steel 1.4305 (AISI 304) Function Electrical operated Pressure discharge bidirectional Stem Not rising Pressure range Please refer to the data sheet Temperature range • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body Stainless steel 1.4408. Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4401 (316) Stem Stainless steel 1.4404 (316) Hand wheel Steel, lacquered Pressure discharge One-sided Stem Not rising Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Function Pneumatic double acting Pressure discharge bidirectional Pilot pressure 6bar (lower pressure on request) Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Refer to the advices on page 8! Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Function Pneumatic single acting with spring return, normally closed (NC). Pressure discharge One-sided Pilot pressure 6bar Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 Installation Only with vertical upwards actuator The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Hand wheel Steel, lacquered Pressure discharge One-sided, two-sided on request Stem Not rising Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 2 parts to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquids, drain water, sludge, food etc. (viscous media, pulverised media with fibre particles, plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (AISI 304) Stem Stainless steel 1.4305 (AISI 304) Lever Steel, lacquered Pressure discharge bidirectional Pressure range Please refer to the table Temperature range • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid