Calibration equipment - Import export

Over the last few years, we at EP-E have designed and introduced a series of primary standards for gases, designed for use in calibration laboratories. As a technology partner of the Physikalisch-Technische Bundesanstalt (PTB) in Braunschweig, our solutions are based on the highest standards. The EP gas bell plungers generate a volume flow which is traceable to the SI units length and time. The pistons are driven by a stepper motor via a spindle. In the initial state one piston is fully retracted and the other fully extended. The volume flow can be set with high precision via the piston cross section and the travel speed. At the end of the calibration process, both pistons are in the opposite position to the initial position. The calibration device is preferably operated with air, which can be supplied with up to 6 bar. The EP gas bell pistons convince by highest measuring accuracy up to 0.15% (k=2).

The EP endurance test benches are used to test various components over a defined cycle for durability, e.g. temperature and pressure cycle tests. A high series quality requires precision and reliability. Operational and endurance tests are necessary in order to be able to demonstrably guarantee high quality. In the form of selection or random sampling tests, components are tested for fatigue and wear by means of load tests, for example under pressure and temperature changes. The tests are used for endurance stress testing of various materials and products with different pressure curves and temperatures. We build test benches according to your requirements: e.g. for long-term or short-term tests, under static or pulsating test conditions and depending on other factors. Present us your requirements!

The test bench is designed for calibration with critically operated nozzles of domestic gas meters or others such as diaphragm gas meters, ultrasonic meters, thermoelectric gas meters. The test bench is specially designed for the calibration of domestic gas meters (bellows gas meters, ultrasonic meters, thermoelectric gas meters). The test bench is modular - 1x6 to 4x6 clamping positions for the gas meters can be combined. Due to the modular design 1 to 12 gas meters can be tested simultaneously. In parallel, up to twelve additional test pieces can be adapted, run in and leak tested. A magazine consisting of three critical nozzles is used as flow transmitter. Optionally, a nozzle drum with nine combinable nozzles can be used. This allows the generation of up to 512 different flow points with highest accuracy.

We offer you standardised complete systems for the measurement of volume & mass flows. The EP LMF®-LaminarMasterFlow® is a complete system for high-precision flow measurement of gases and air. The LMF® system consists of a flow processor, a Laminar Flow Element (LFE) as measuring section, a cable set and a sensor package. The flow measurement is performed by means of Laminar Flow Elements (LFE), which are available in different sizes and cover a measuring range from 0.01 to 700 m³/h. (optionally up to 4000 m³/h).

The high-precision calibration laboratory is accredited according to DIN EN ISO/IEC 17025 for flow calibration of flowing gases. The EP calibration laboratory is accredited by the DAkkS according to DIN EN ISO/IEC 17025:2005 for calibrations of gases in-house and on-site under the procedure number D-K-21444-01-00. We offer calibrations for gas flow measurement as well as temperature, humidity and pressure measurements. In addition, we calibrate all measured variables of the test bench directly at your site. Our experienced technicians also check the harmonious interaction of all sensors, so that the entire system is perfectly tuned. The opening of our new calibration laboratory in Asia enables us to offer you even better service internationally.

Learn how to efficiently manage and monitor your measuring and testing equipment. In this training course, you will learn the basics of measuring and test equipment management, the requirements for calibration and documentation. The training is aimed at all those who are responsible for or interested in measuring and testing equipment. Topics of the training course: Measuring and testing equipment management as a pillar of quality assurance; Measuring and test equipment management as part of the quality management system – test equipment officer; Suitability of devices and sensors as measuring and testing equipment; Traceability and calibration; Documentation and employee training; Monitoring and maintenance of the measuring equipment database.

Learn how to efficiently manage and monitor your measuring and testing equipment. In this training course, you will learn the basics of measuring and test equipment management, the requirements for calibration and documentation. The training is aimed at all those who are responsible for or interested in measuring and testing equipment. Topics of the training course: Measuring and testing equipment management as a pillar of quality assurance; Measuring and test equipment management as part of the quality management system – test equipment officer; Suitability of devices and sensors as measuring and testing equipment; Traceability and calibration; Documentation and employee training; Monitoring and maintenance of the measuring equipment database.