BURSTER PRÄZISIONSMESSTECHNIK GMBH & CO KG
—Ready to use with any make of sensor for your measurement needs, manufacturer independent
—Ultra-fast pushbutton configuration
—Automatic sensor recognition due to burster TEDS
—Expandable fieldbus interface via the bus controller
—Supports Ethernet based fieldbuses such as PROFINET, EtherCAT, EtherNet/lP in combination with the Fieldbus Controller 9251
—Up to 8 instrumentation amplifiers can be cascaded to a fieldbus controller
—Full measurement-data export facility
—Suitable for force, pressure, displacement, rotational speed and torque measurements, including combined measurements
—Tare facility via pushbutton or I/O signals for each 9250 amplifier
—Up to two real-time signals/limit switches per amplifier module
—Versatile configuration using DigiVision PC software via USB port
—High measurement accuracy
—Space-saving design for control-cabinet mounting
—Adjustable cut-off frequencies
In the field there is a frequent need to measure sensor readings rapidly and easily right at the sensor and to transfer them directly to a PC without additional amplifiers or converters. The 9206 USB sensor interface can satisfy this requirement admirably, thanks to its „plug & measure“ design. The USB connection means installation could not be simpler.
Mobile test measurements via laptop
Laboratory test set-ups
Instrumentation and control
Diagnostic measurements in the chemical industry
PC-based recording of expansion figures in bio engineering
— Inexpensive "Plug & Measure" design
— Simple connection via PC USB port
— 24 bit resolution
— High-speed measurement of up to 1200 readings/sec.
— Convenient configuration and analysis software DigiVision
— Pt100 as option
— LabVIEW and DLL drivers free of charge
— Integration in customer-owned software
— 6 wire technology for the highest precision
In practice the requirement often arises to convert the measurement signals of a sensor into a standard signal in the simplest possible manner in the immediate proximity of the sensor. This permits trouble-free, low-loss transmission of measured values over longer distances to an instrument board or plant controls.
Ideally suited for this purpose is the in-line measuring amplifier, which is inserted in between in the connection cable by means of plug contacts. Owing to its compact, robust design and low weight, it finds use in almost any application. Even movable locations subject to forces of acceleration, for example manipulators, present no problems. It is intended mainly for use of control cabinets in just about any location and is matched to a specific sensor.
— Particularly space-saving and lightweight
— Voltage output 0 ... ± 10 V
— Designed as in-line measuring amplifier
— Non-interchangeable and short circuit-proof
The newly developed sensor PROFIBUS module model 9221 is predestined for the integration of various analog sensor output signals into complex, net worked and peripheral automation structures. This module finds its fields of application in the industrial automation technology as well as the test rig technology based on its secure and reliable transfer mode, the fast transfer speed and its simple construction.
The inputs (e.g. PLC signal gauge) and outputs in addition to the external control allow a zero compensation by trigger via proximity switch or fast alerting on passing of set point values. Industrial type connection and mounting techniques enable the user the adaption and integration in the existing mechanical and electrical environment.
The excellent quality of measurement together with the high grade capture of mean values also enable the application in research and development.
The use of standardized PROFIBUS protocols makes the connection an easy task for the programmer.
DIGITAL DISPLAY FOR STRAIN GAUGE UNITS, POTENTIOMETERS, DC/DC SENSORS AND STANDARD SIGNALSHighly accurate, 2 displays for min and max peak values, RS232 or RS485, TARA and HOLD functions, optional: powerful PC software for collection and processing of measured data
Model 9180 supports force, pressure and torque sensors operating on the strain gauge principle, as well as the connection of position and angle sensors in potentiometer or DC/DC configuration. It also allows the measurement of process signals ± 1 V/ 5 V/ 10 V or 0 ...1 mA, 0(4) ... 20 mA. The current measured value is indicated on the 14 mm high LED main display, while a second display located directly below provides a reading of the peak value.
Automatic inspection and test unit:
Automatic choice of measuring ranges from 200 μΩ to 20 kΩ
Resolution up to 1 nΩ
Standard interfaces IEEE488, RS232, RS485, (USB and Ethernet option)
Checking of tolerances, classifi cation with statistics
Highest measuring accuracy:
Measuring error ≤ 0.01 %
Future-orientated measuring method with thermal e.m.f. compensation.
High level of stability due to constant comparisons with internal reference values.
Current regulation results in voltage-free disconnection, calculation of cooling curves of coils.
Setting for measuring current entry for absolute or relative limits, classifi cation with statistics, bar display for calibration of measuring probes, determination of resistivity, and many other functions.
Areas of application:
High-precision measuring, Series tests, coil, motor and transformer windings, Recording of cooling curves, Meter probes, resistivity values, contact resistances
Based on its specifications, this device can be used in various applications. It is especially suitable for resistance measurement on insulating materials such as e.g. cable insulations, foils, textiles, surfaces, insulating liquids, etc. With a test voltage of 45 V, 100 V, 250 V and 500 V the device fulfi ls most test specifi cations such as e.g. DIN 51953, 53482 and 54345. The guard switching allows single resistance measurements in a triangle wiring. This could be e.g. a two line cable with common shield or the measurement of insulating materials on a guardring measurement cell.
The selection of the measurement range is done manually or automatically.
— Resistance measurement range from 50 kΩ ... 10 TΩ
— Current measurement range 10 pA ... 10 mA
— Automatic / manual switch of measurement range
— Test voltage 45 V, 100 V, 250 V, 500 V
— Limit value indicator
— RS232 interface (USB and Ethernet option)
The SENSORMASTER 9163 covers a wide range of applications in which process values need to be measured, displayed, analyzed and transferred to higher-level control systems. Typical applications include measuring geometric values in production, for instance differential measurements, or testing material properties in the laboratory.
The measured values can be transferred via USB, RS232 or analog output.
— For force, pressure or torque measurements using strain gauge sensors
— For position or angle measurement using potentiometric or DC/DC sensors
— For temperature measurement using Pt 100 sensors or thermocouples
— Optional multi-channel model
— Optional Profibus or serial interface
— 0.1 % measurement accuracy plus sensor-specific linearization
— Range of mathematical functions (e.g. differential measurement)
— OK/NOK feedback on multi color display and via 4 alarm limit outputs
— High sampling rate (500/sec.)
Inside the multi-component force transducer are two webs, each offset by 90°, each with a strain gage full bridge, which convert the radially acting X / Y forces on the guide bush into an electrical signal.
Due to the sensor body made from a block with its special structure, the sensor has a very high degree of dimensional accuracy and low crosstalk between the two forces.
Due to the special design, the sensor has excellent linearity properties and is designed for a long service life in dynamic applications.
The two independent signal connections allow flexible adaptation and further processing.
— Measuring ranges: 0 ... 4448 N / 0 ... 2224 N (0 ... 1000 lbs / 0 ... 500 lbs); 0 ... 8896 N / 0 ... 4448 N (0 ... 2000 lbs / 0 ... 1000 lbs)
— Further measuring ranges on request
— Non-linearity < 0.1 % F.S.
— Low cross talk < 0.75 % F.S.
— High dimensional accuracy, because sensor is made from one part
— Excellent price/performance ratio
The RESISTOMAT® model 2320 is a universally applicable and easy to operate measurement device for low-ohmic resistances. The light and handy device in a stable IP54 plastic housing with membrane keypad is likewise suitable for use in service, laboratory or on the production floor. The power supply is done via built-in rechargeable battery packs or by standard batteries.
If need be, the temperature of samples can be measured and the sample resistance is subsequently compensated to fit the value at 20°C. This applies for samples with resistances depending on the sample’s temperature. The temperature coefficients for copper and aluminium are included as standard. A third and fourth coefficient may be set individually for any given material to be measured.
— Measuring ranges from 40 mΩ to 4 kΩ
— Resolution up to 10 μΩ
— Measuring accuracy 0.05 % Rdg.
— Temperature compensation
— Bipolar measurement
— Input voltage protection up to 415 Vrms