Machine mounted - Import export

Separates the free beans from the mechanically harvested green bean clusters. Machine primarily comprised of a drum fitted with hooks of special shape. Mobile machine mounted on rollers so that the position of the drum can be adjusted in relation to the fall of products above the drum.

Spring isolators can be used for source and sender vibration isolation. The springs are manufactured of a special spring steel wire and KTL coated. Every spring isolator can be provided with an additional damping cushion of stainless-steel. Elemente with a frequency range between 3-4 Hz can be provided with a viscous damping, too. Spring isolators with a natural frequency range of 3-5 or 4-6 Hz are especially made for higher forces. They can be expanded in size and load-capacity without any difficulty. Spring isolators of RG+ are available for four different natural frequency ranges: Spring isolators with a natural frequency of 3-4 Hz Spring isolators with a natural frequency of 5-6 Hz Spring isolators with a natural frequency of 7-9 Hz Spring isolators with a natural frequency of 3-5 or 4-6 Hz

This dot peen marking range is a marking solution equipped with innovative functionnalities especially developed for integration in production processes PRODUCT ADVANTAGES ROBUST Frame in moulded aluminium. Each axis is fitted with a ball bearing and a transmision system with automatic compensation ERGONOMIC Vertical or horizontal position, easily adaptable to any rackmount configuration due to a connection at the back of the machine. HANDY Mounting connection cable can be connected at the back or on top of the marking head, to facilitate the integration. Three mounting bracket positions are available. FLEXIBLE First integrated marking equipment fitted with a 16 bus card for greater time efficiency and productivity.

Our drum type Pre-Cleaning Machines; It is produced in the capacity range of 20 - 100 tons per hour. With the ÇSI Pre-Cleaning Machine, all unwanted foreign substances (garbage, dust, straw, etc.) in all kinds of grains (wheat, barley, corn, canola, soybean, etc.) are perfectly separated at a level that does not require cleaning again. Thanks to its airlock and cyclone as well as its excellent filter, it leaves absolutely no waste in the environment. Our sieves, which are designed according to the structure of all kinds of products, are easily mounted on the machine. Thanks to the brushes placed on the sieves, the sieves constantly clean themselves as the machine operates. With its high suction power dust collection and filter system, it does not leave any dust waste in the environment. The Pre-Cleaning Machine, designed by ÇSI engineers using advanced technology, will provide the cleaning you need for many years.

Radial scanning machine is used to separate low density substances from high density grain products such as wheat, barley, corn and similar. Separates foreign substances such as dust, sand and small seeds in wheat. Wheat entering the machine from the wheat inlet is filled into the vibro feeder and distributed smoothly across the width of the air duct. Here, in the horizontal aspiration channel, the product is separated from low density materials through its double adjustable wall. The fan of the radial scanning machine is mounted on the main body through bearings. The outer body is made of sheet metal, and the foot part and the outlet nozzle located on the foot part are mounted on the body.

We offer the full range of solutions for process automation tasks implemented with Foundation™ fieldbus and PROFIBUS-PA: The portfolio includes power supplies, power conditioners, multibarriers as well as junction boxes in IP20 and IP67. The range also includes passive connectivity products such as fieldbus cables, field distributors and terminating resistors. The components are suitable for use in harsh environments and can directly be mounted on the machine or in the process.

Other information Series 2828 Inner height hi: 32 mm Inner widths Bi: 50 - 400 mm bending radii R: 63 - 300 mm Pitch: 56 mm E-Chain® with crossbars at every link Series 3838 Inner height hi: 42 mm Inner widths Bi: 50 - 400 mm bending radii R: 75 - 350 mm Pitch: 67 mm E-Chain® with crossbars at every link Series 4040 Inner height hi: 56 mm Inner widths Bi: 50 - 600 mm bending radii R: 135 - 500 mm Pitch: 91 mm E-Chain® with crossbars at every link Series 5050 Inner height hi: 80 mm Inner widths Bi: 50 - 600 mm bending radii R: 150 - 1000 mm Pitch: 91 mm E-Chain® with crossbars at every link Series 2928 Inner height hi: 32 mm Inner widths Bi: 50 - 400 mm bending radii R: 63 - 300 mm Pitch: 56 mm E-Chain® with crossbars at every other link Series 3938 Inner height hi: 42 mm Inner widths Bi: 50 - 400 mm bending radii R: 75 - 350 mm Pitch: 67 mm E-Chain® with crossbars at every other link Series 4140 Inner height hi: 56 mm Inner widths Bi: 50 - 600 mm bending radii R: 135 - 500 mm Pitch: 91 mm E-Chain® with crossbars at every other link Series 5150 Inner height hi: 80 mm Inner widths Bi: 50 - 600 mm bending radii R: 150 - 1000 mm Pitch: 91 mm E-Chain® with crossbars at every other link Series 4040HD Inner height hi: 56 mm Inner widths Bi: 50 - 600 mm bending radii R: 135 - 400 mm Pitch: 91 mm E-Chain® with crossbars at every link Series 5050HD Inner height hi: 80 mm Inner widths Bi: 50 - 600 mm bending radii R: 150 - 500 mm Pitch: 91 mm E-Chain® with crossbars at every link Series R7728 Inner height hi: 32 mm Inner widths Bi: 50 - 300 mm bending radii R: 100 - 300 mm Pitch: 56 mm E-Tube, swivel lid Series R7838 Inner height hi: 42 mm Inner widths Bi: 50 - 300 mm bending radii R: 125 - 350 mm Pitch: 67 mm E-Tube, swivel lid Series R8840 Inner height hi: 56 mm Inner widths Bi: 75 - 462 mm bending radii R: 150 - 500 mm Pitch: 91 mm E-Tube, swivel lid Series R9850 Inner height hi: 80 mm Inner widths Bi: 75 - 462 mm bending radii R: 200 - 1000 mm Pitch: 91 mm E-Tube, swivel lid Series R8840HD Inner height hi: 56 mm Inner widths Bi: 75 - 462 mm bending radii R: 150 - 400 mm Pitch: 91 mm E-Tube, swivel lid Series R9850HD Inner height hi: 80 mm Inner widths Bi: 75 - 462 mm bending radii R: 150 - 500 mm Pitch: 91 mm E-Tube, swivel lid Assembly tool for E4-series For the practical opening and closing of the E4 series. Big savings in assembly time Assembly tool for E4-series ATEX/ESD: Excellent match with special material igumid ESD (on request). "Mounted on the side" unsupported application possible High torsional stiffness System E4/4 proven in long travels Other information Series 2828 Inner height hi: 32 mm Inner widths Bi: 50 - 400 mm bending radii R: 63 - 300 mm Pitch: 56 mm E-Chain® with crossbars at every link Series 3838 Inner height hi: 42 mm Inner widths Bi: 50 - 400 mm bending radii R: 75 - 350 mm Pitch: 67 mm E-Chain® with crossbars at every link Series 4040 Inner height hi: 56 mm Inner widths Bi: 50 - 600 mm bending radii R: 135 - 500 mm Pitch: 91 mm E-Chain® with crossbars at every link Series 5050 Inner height hi: 80 mm Inner widths Bi: 50 - 600 mm bending radii R: 150 - 1000 mm Pitch: 91 mm E-Chain® with crossbars at every link Series 2928 Inner height hi: 32 mm Inner widths Bi: 50 - 400 mm bending radii R: 63 - 300 mm Pitch: 56 mm E-Chain® with crossbars at every other link Series 3938 Inner height hi: 42 mm Inner widths Bi: 50 - 400 mm bending radii R: 75 - 350 mm Pitch: 67 mm E-Chain® with crossbars at every other link Series 4140 Inner height hi: 56 mm Inner widths Bi: 50 - 600 mm bending radii R: 135 - 500 mm Pitch: 91 mm E-Chain® with crossbars at every other link Series 5150 Inner height hi: 80 mm Inner widths Bi: 50 - 600 mm bending radii R: 150 - 1000 mm Pitch: 91 mm E-Chain® with crossbars at every other link Series 4040HD Inner height hi: 56 mm Inner widths Bi: 50 - 600 mm bending radii R: 135 - 400 mm Pitch: 91 mm E-Chain® with crossbars at every link Series 5050HD Inner height hi: 80 mm Inner widths Bi: 50 - 600 mm bending radii R: 150 - 500 mm Pitch: 91 mm E-Chain® with crossbars at every link Series R7728 Inner height hi: 32 mm Inner widths Bi: 50 - 300 mm bending radii R: 100 - 300 mm Pitch: 56 mm E-Tube, swivel lid Series R7838 Inner height hi: 42 mm Inner widths Bi: 50 - 300 mm bending radii R: 125 - 350 mm Pitch: 67 mm E-Tube, swivel lid Series R8840 Inner height hi: 56 mm Inner widths Bi: 75 - 462 mm bending radii R: 150 - 500 mm Pitch: 91 mm E-Tube, swivel lid Series R9850 Inner height hi: 80 mm Inner widths Bi: 75 - 462 mm bending radii R: 200 - 1000 mm Pitch: 91 mm E-Tube, swivel lid Series R8840HD Inner height hi: 56 mm Inner widths Bi: 75 - 462 mm bending radii R: 150 - 400 mm Pitch: 91 mm E-Tube, swivel lid Series R9850HD Inner height hi: 80 mm Inner widths Bi: 75 - 462 mm bending radii R: 150 - 500 mm Pitch: 91 mm E-Tube, swivel lid Assembly tool for E4-series For the practical opening and closing of the E4 series. Big savings in assembly time Assembly tool for E4-series E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Selection aids Installation instructions Joining, separating and opening of the E-Chain® and E-Tubes. Assembly Instructions Application examples Applications in various industrial sectors and in the igus® test laboratory. E4/4 "Mounted on the side" - Travel distances over 200 m "Mounted on the side" - Travel distances over 200 m Extensive unsupported lengths for "side-mounted" applications Roller E-Chain® links available (with roller chain) Max. travel distance: 200 - 800 m High torsional stability Manifold interior separation potentials Large accessory kits Typical industrial sectors and applications RTG, quayside cranes, many other types of cranes Composting plants Gypsum, concrete, chemical and mineral plants, as well as agricultural plants Machine tools: unsupported, side-mounted applications Construction machinery ESD applications Heavy machinery Steel works Shipyards Welding plants ATEX/ESD: Excellent match with special material igumid ESD (on request). "Mounted on the side" unsupported application possible High torsional stiffness System E4/4 proven in long travels

Round baseplates with T-slots are used for constructing modular fixtures. These baseplates are positioned and mounted directly on machine tables. The precise longitudinal and transverse slot spacing ensures very high repeat clamping accuracy. The aligning holes are used to align the baseplate on the machine table. Please order locating pins to locate the baseplates separately. Ring bolts with T-nuts for hoisting are supplied. Other dimensions available on request. On request: other dimensions. Drawing reference: 1) hole for DIN 912 cap screw (D4)

Body and jaw holder hardened and ground. Note for ordering: Supplied with hexagon crank handle. Order jaw plates separately. Note: Mechanically operated centric vice. Suitable for automation: prepared with gripper slot for handling systems. Flexible mounting: suitable for zero-point systems, mounting on machine tables or on custom systems via a baseplate. Centring precision: +/- 0.02 mm. The use of a torque wrench is recommended to achieve a controlled clamping force. Features: Clamping slide and spindle nut in one piece Slots and fastening threads for mounting attachment jaws Reversible jaws (accessories) with lateral thread for workpiece stop enables a wider clamping range Good swarf and coolant removal

The universal brackets for shaft alignment Stored premounted in the case for instant usage Mounts on machine shaft in less than a minute Standard chains fit shaft and coupling diameters of approx. 15 mm to 200 mm / 5/8“ to 7 7/8“ This universal bracket set contains all parts needed for quick, stable mounting of the measurement components. It fits onto any shaft or coupling approx. 15 mm to 200 mm /5/8" to 7 7/8“ in diameter. Stored premounted in the case, the brackets are always ready to use and quickly in place. The chain may be used as a plumb bob to accurately determine the dimension from coupling center to front foot.

L-SEALERS BSF SERIES The manuals bench L-sealers BSF series are very simple and practical. Allow to obtain the envelopes perfectly sealed, using standard fold film. They are suitable for use in laundries and textile sector in general and in the paper industry, but are also helpful in the food industry for the packaging of the bread. Sealing bar with manual operation. The choice of the machine must take into account that: the dimensions of the box (height + depth) must not exceed the maximum width of the reel mounted on the machine (depending on the model) also considering that there must always be at least 50 mm of waste. To confirm that the machine is suitable, we always advise you to contact us and report the measurements of the boxes to be packaged.

Sectional roller brushes are available in several different configurations to suit specific machines. Each brush is mounted and locked next to its neighbour to create a roller brush that can be be replaced in worn areas can be removed and replaced They can be colour coded to suit specific areas of usage and can be manufactured in any dimension, filament and stiffness.

The male cable plug is used for connecting welding cables. The universal ŁW / ŁP type cable plug is used for connecting welding cables to the welding machine. It is mounted on mass and current wires. The plug together with the aggregate socket guarantees reliable electrical connection of the cable to the welding device. This type of connector is used in welding semi-automatic and MMA and TIG welding machines of most device manufacturers. Technical data: For cable: 35-50mm Diameter of the bolt: 12mm Pin length: 19mm Max. conductive current in 60% duty cycle (A): 316 Max. conductive current in 100% duty cycle (A): 285

The male cable plug is used for connecting welding cables. The universal ŁW / ŁP type cable plug is used for connecting welding cables to the welding machine. It is mounted on mass and current wires. The plug together with the aggregate socket guarantees reliable electrical connection of the cable to the welding device. This type of connector is used in welding semi-automatic and MMA and TIG welding machines of most device manufacturers. Technical data: On the cable: 10-25mm Diameter of the pin: 9mm Pin length: 11mm Max. conductive current in 60% duty cycle (A): 190 Max. conductive current in 100% duty cycle (A): 180

Our Oak Veneer Faced Black Dyed MDF comprises of a real Oak, Crown Cut. veneer that is factory bonded to both sides of a 10mm black dyed MDF core. The overall thickness of 11mm the panels is 11mm. This makes them perfect for a wide range of domestic and commercial projects. This includes, but is not limited to, decorative wall panelling and wall cladding. Available cut to size, we can offer strips of black dyed MDF with an Oak veneer face, in any width and up to 2440mm long. This is perfect for creating low cost Oak faced Slat Wall feature walls in any room. Alternatively, and conveniently, we also offer easy to mount, pre-machined Oak faced black MDF slat wall panels These are available in our standard easy to ship size, or full sheets upon request. Not only can we supply your panels cut to size, we can also lacquer your Oak Faced Black MDF panels so you don’t have to. Our in-house spraying capability means we can finish your panels before they leave here and arrive with you.

Roll, Sandwich Hamburger and similar sized products and Francala Bread are individually wrapped. Our machine has a servo motor system. Thanks to the touch screen and PLC on the machine, product package length, photocell adjustment and machine speed can be adjusted as desired. There is a sensor control system that prevents jamming of the product. If the product location is not correct, it stops the machine. All surfaces and covers that are in contact with the product in the machine are made of 304 quality chrome-nickel metal. Rotating jaw system. It packs 115 products per minute (roll, sandwich hamburger and similar products), and 83 products per minute in Francala Bread. It easy to use. Optionally, it is produced so that a coding device can be mounted on the machine. Cellophane bobbin is easy to disassemble and install, the place where it is mounted is an air system and PLC controlled shaft.

MAGTROL offers a wide range of Load-Force-Weight Transducers with optional integrated electronics or Load Monitoring Units (LMU) with B.I.T.E. functions creating an ideal measurement system which continuously checks for overloads and short circuits. Idealy for use on Safety Applications according to ECE-R10, ISO 13849-1 : CAT4 & PLe and IEC 62061 : SIL3 (LE 6XX SERIES); ISO 13849-1 : CAT2 & PLd and IEC 62061 : SIL2 (LE 4XX SERIES) Magtrol Load Measuring Pins are used to measure load and force, and provide overload protection. The pins are mounted into machines in place of normal shafts and fitted with strain gauges, allowing them to produce a signal proportional to the measured load. Manufactured in Switzerland, Magtrol’s LE Series Load Measuring Pins are rugged with high resistance stainless steel and tight construction. Available in several standard ranges from 2.5 kN to 1 250 kN. .... more information www.magtrol.com

With its compact, bearingless, maintenance-free design, the new TF Torque Flange Sensor from Magtrol brings many appealing advantages to torque measurement applications. The TF’s high torsional rigidity supports direct mounting on the machine shaft or flange, avoiding the use of couplings on one side. This allows easy integration into a test system, shortens the overall length of the test bench and reduces costs. Based on strain-gauge technology, the TF Sensor’s precise telemetry system enables highly accurate signal transmission. A signal amplifier mounted in the measuring flange amplifies the measuring signal, modulates it to high frequency and transmits it inductively (via the HF transmitter) to the receiver. In the receiver, the digitized torque signal is transformed into an analog output signal of ±10 VDC. Rotational speed can be measured and converted to a TTL output signal with the optional speed pickup. more info www.magtrol.com

Magtrol Miniature Load Measuring Pins are used to measure load and force and provide overload protection. The pins are mounted into machines in place of normal shafts and fitted with strain gauges, allowing them to produce a signal proportional to the measured load. Manufactured in Switzerland, Magtrol’s MB-02 Series Miniature Load Pins are rugged with high resistance stainless steel and tight construction, designed specifically for use in harsh industrial environment.

Quality that inspires It isn’t just the price-performance ratio of MANOK that is impressive. With its incredible holding power, precision and rigidity, MANOK has already surprised many users who never would have imagined that this kind of quality could be found in a manual clamping device. In addition, you can also mount an end-stop to the MANOK in no time at all: Simply fasten the inside end-stop directly onto your machine tool table or mount a front end-stop on the face of the clamping taper. That’s it! Absolute versatile implementation MANOK is not only practical and economical, but it is also extremely versatile. For instance, the integrated actuation lever makes this possible by functioning as an additional force accumulator and acts as an anti-vibration device during milling.

The machine is intended for individual farms. It is used for tedding and spreading lowstemmed plants. The belt tedder-rake can rake dry and dry hay into longitudinal shafts on areas with a slope of up to 22%. The tedder-rake is a machine designed to be mounted on a tractor with a power of 12 HP. It is driven by the tractor PTO - through the articulated telescopic shaft.

D-SUB Standard, Solder pin – Angled, .370" 9.4 mm, Precision machined contacts, Metal bracket Mounting styles: — with mounting bracket and 4-40 UNC or M3 threaded insert — with mounting bracket, PCB clip and 4-40 UNC or M3 threaded insert — Quality class 3 (also available in quality class 1) — Shell: Steel tin plated (brass tin plated or stainless steel available on request)

Finish: Light grey Seven auto programmes; four timed programmes Sensor-controlled auto programmes stop drying when clothes are dry Dryer can be mounted on washing machine LCD display and interface on local language (13 languages) Reversible door (right/left) Manual or automatic drainage of condensation water – drain hose included Stacking brackets for column installation included Connection: 230V / 1ph / 13A / 50Hz / Max effect: 2.8kW Can be reconfigured to: 230V / 1ph / 10A / 50Hz / Max effect: 2.25kW Condenser dryer

A Chick Workholding Foundation Plate is tailored to fit the machine’s specifications. A standard grid pattern to simplify designing, cataloguing and utilisation of fixtures, providing consistency and repeatability to set-ups. Length and width tailored to the machine’s work envelope. Precision ground cast iron to 35mm thick. 50mm spaced holes, drilled and tapped, for use as both location and hold down. Sealed with chip plugs. An alpha-numeric labelling system. Minimises set up time from workholding system to system. Machine interface mounting holes, customised for each machining centre.

Blank connector to be machined to suit specific drawtube threads Other lengths of connector are available We can supply drawnuts with the correct thread to suit your machine Used for mounting a BT200 chuck onto a drawtube, this connector is supplied blank to be machined out to the required thread. **Some machine setups may require the use of extended connectors as well as a drawnut**

Blank connector to be machined to suit specific drawtube threads Other lengths of connector are available We can supply drawnuts with the correct thread to suit your machine Used for mounting a B series chuck onto a drawtube, this connector is supplied blank to be machined out to the required thread. **Some machine setups may require the use of extended connectors as well as a drawnut**

Blank connector to be machined to suit specific drawtube threads Other lengths of connector are available We can supply drawnuts with the correct thread to suit your machine Used for mounting a BT series chuck onto a drawtube, this connector is supplied blank to be machined out to the required thread. **Some machine setups may require the use of extended connectors as well as a drawnut**

Blank connector to be machined to suit specific drawtube threads Other lengths of connector are available We can supply drawnuts with the correct thread to suit your machine Used for mounting a BB200 chuck onto a drawtube, this connector is supplied blank to be machined out to the required thread. **Some machine setups may require the use of extended connectors as well as a drawnut**

Uses the HSK-A type, time-proven tool holder shank to connect the head and the work-piece holder. Off-line setup in advance allows quick work-piece changing, minimizing machine downtime. Accepts a variety of workholders Excellent workpiece accessibility In the case where you can’t mount the head directly to your machine table, please use this mounting plate. We can supply a blank that is customisable and also manufacture a special mounting plate just for you. For more information, please feel free to contact us.