Pipes for air - Import export

Fine bubble aeration system for lagoons & large surface area ponds. HDPE Floating Feed pipe sized to provide the required air flow Air supply pipe to difusers Aquatube 70 type Tubular Diffusers Stainless Steel Diffuser Feed Section Concrete ballast to stabilise the diffuser assembly Cost-effective solution Low maintenance Specific modular system Adaptable to any lagoon or large pond Low maintenance requirements Very reliable system easy to install and operate Very competitive design and scope of supply Significant mixing of the total volume within the lagoon The active biomass is aerated effectively and efficiently.

IT PROVIDES THE MIXTURE OF DIFFERENT PRODUCTS IN A HOMOGENEOUS WAY. THE BODY IS MADE UP OF 4-5 mm SHEET AND HAS A SINGLE-SHAFT SUDDEN DISCHARGE FROM A THICK-FLAXED PIPE. FILLING IS DONE FROM THE TOP AND THE PRESSURE BALANCE DURING FILLING IS MAINTAINED BY AN AIR PIPE. BOTH THE LOWER AND THE UPPER COVERS ARE PINEMATIC CONTROLLED AND THE OPERATION OF THE ROTOR IS PROVIDED BY A REDUCER. THE OUTPUT OF THE REDUCER AND THE OUTPUT OF THE MIXER ARE DIRECTLY COUPLED. A DOUBLE SPIRAL LEAF IS ALIGNED ON THE MAIN SHAFT IN ORDER TO MAKE THE RAW MATERIAL TO BE MIXED IN A HOMOGENEOUS FORM DURING THE MIXING.

IKO Linear Bushing G is a high load capacity type linear motion rolling guide in which the external cylinder performs endless linear motion on a shaft with grooved raceway. It is a linear bushing with large load capacity despite being simple and very compact. Since the external cylinder and shaft with grooved raceway dimensions are individually managed, each can be freely added and exchanged. Click here for details on the interchangeable type High Load Capacity The structure in which balls in two rows have contact with the track groove of the shaft allows greater rigidity and larger load capacity. Solid Shaft and Hollow Shaft There are two types of shafts with grooved raceway solid shaft LMG and hollow shaft LMGT. The hollow shaft is useful for piping, wiring, air removal, etc. Dimensionally Compatible with Linear Bushings Dimensionally compatible with the Linear Bushing LM Series to allow easy replacement.

Coating of pipings and air ducts, firing, boiler and heating systems, tanks, exhaust systems, silencers, light-metal bodies on utility vehicles Repairs to mechanically (stone impact) or chemically (de-icing salt) damaged aluminium rims Shielding of non-metallic materials, e.g. cardboard, wood, glass or plastics etc. Advantages and benefits Excellently suited for sole, decorative corrosion protection Universal protective and decorative coating for all materials Economical due to low consumption and self-cleaning spray valve High covering capacity Fast-drying

plunger Ø 35 mm, stroke 10 mm off-position extended contact with air pressure pipe thread G1/4 max. 500 bar, as per data sheet B1.921

plunger Ø 20 mm, stroke 8 mm off-position extended contact with air pressure pipe thread G1/4 max. 500 bar, as per data sheet B1.921

plunger Ø 16 mm, stroke 6 mm off-position extended contact with air pressure pipe thread G1/4 max. 500 bar, as per data sheet B1.921

High performance pipe clamp for plumbing, ventilation, air conditioning and industrial application Excellent loading capacity Easy installation through wide opening High performance noise and vibration absorption Precise fitting for every pipe We would be very pleased to support you with all your individual questions and suggestions regarding WUS. Give us a ring or leave a message indicating the information you need. We will contact you as quickly as possible. Your WUS team

Air-water / air-air heat exchanger as smooth tube heat exchanger up to 1,000 ° C Smooth tube heat exchanger as an air / water heat exchanger In the case of air-water heat exchangers (also called gas-water heat exchangers), a temperature exchange takes place between a gas (usually air) and a liquid. As a rule, the liquid medium flows inside the pipes, while the gaseous medium flows around the pipes outside the pipes. Smooth tube heat exchangers can cover various areas of application: heating, cooling and condensing as well as heat recovery. Smooth tube heat exchanger as air-to-air heat exchanger Smooth tube heat exchangers are also often used as air-to-air heat exchangers. In this application, a gas (e.g. exhaust air or exhaust gases) flows inside the pipes and a gas (e.g. fresh air) outside the pipes around the pipes.

longitudinal welding with overlap pipe for transporting air and dust. TRANSQuick system is made of galvanised steel sheet, 0.7 and 0.9 mm in thickness. Depending on the wall thickness there are available various lengths 0.7 mm thickness L=500 / 1000 / 1480 mm. 0.9 mm thickness L=500 / 1000 mm

The RAVAV regulator is dedicated for forced ventilation systems and is an important component for installations with variable air flow. The regulator casing is made of Z 275 galvanized sheet. Optionally, it is possible to use the 1.4301 stainless steel to build the casing. Casing sides with factoryinstalled EPDM rubber gaskets ensure tight connection to ventilation ducts. Inside the casing, the adjusting damper is also insulated (depending on the control mechanism). The servomotor is installed on the control unit casing so as to allow for thermal insulation of the system. The regulator is also available in the version with preinstalled 50 mm insulation and a galvanised steel shield. The measuring system based on aluminum impact pressure tubes and pressure relieve stub pipes ensures reliable measuring of the air flow. Sensor, control unit and servomotor are integrated in one device.

HP- 40 bar air receiver options Standard (horizontal on the base-frame or vertical ) the HP- 40 bar air receiver is hot galvanised with accessories, including safety valve and Bekomat drain system. Depending on the location and country, the air receivers have to comply with the local codes and certifications. All Codes and certifications are available : CE-PED, ASME VIII, CRN for Canadia , TR CU suiting to Russia, Kazakhstan, Belarus, SELO code in China, South Korea 40 bar certification. NR13 for Brazil… HP – 40 bar piping and accessories 40 bar piping between the compressor, HP air receiver and the HP dryer flanges, supports, safety warrant and mounting accessories, shut off gates /40 bar stop valve is included in standard. Also available : – accessories for specific HP connection installation before the dryer ; elbow… HP- 40 bar air Dryer options Stainless steel condenser, dew point alarm, Bekomat draining system. Water cooled condenser is recommended for ambient temperatures...

More info More info More info More info More info 40bar PET Compressors Select the machine The AF 40 bar Piston Oil Free PET compressor Package Turn-key installations designed to meet the most stringent standards and conditions to ensure round-the-clock operation. Complete solutions from 225 to 3200 m³/H, electric motors from 45 to 550 kW. Features Benefits Intercoolers and separators Features Hot galvanized connection piping to aftercooler inlet. Air temperature indicator on connection piping. Spring loaded safety valve on separator upper head. Air pressure indicator on separator body. Air temperature indicator on separator body. Drain valve and automatic condensate trap on separator lower head. Benefits Optimized compressed Air Quality maximum. Cooling Efficiency at each compression stage. Air Dryer Features Stainless steel flexible connections from the galvanized air receiver to the 40 bar air dryer. Stainless steel dryer with integrated 1 micron filter, dew point alarm...

The DR 206 discharge row offers air supported separation of materials, such as sheets in offset printing. The discharge row comprises several discharge nozzles mounted to slide on a carrier pipe. The air supply is centrally adjustable by the operator and each nozzle is also individually adjustable.

The term inline filter refers to an expandable, bolted, modular system. Depending on requirements, appropriate filter and air injection sections are connected together in series. The capacity range extends from approx. 10,000–300,000 m³/h. RS / RX filter The RS / RX series are a proven, expandable, modular system with low-pressure purge-air cleaning. Depending on requirements, appropriate filter and air injection sections are connected together in series. The capacity range extends from approx. 20,000–300,000 m³/h. RS / RX filters are suitable only for vacuum and positive pressure operation. The housing parts are usually made of 2 mm thick galvanised sheet steel. A thicker material in a painted execution as well as in stainless steel is also optionally available. The RS / RX series is 2.85 m wide. Filter hose lengths of 3 m (standard) and 4 m are available for this. The RSEC series has been designed for smaller air quantities and for above-roof installation. This series has a housing width of 2.4 m and 2 m-long filter hoses. The filter hoses are manufactured from polyester needle felt; the filtering direction is from the outside inwards. Filter cartridges and filter tubes are alternatively possible. The filter hoses are cleaned off using the material-preserving low-pressure purge-air system. The purging trolley inside the clean air compartment drives over the hose openings either continuously or controlled by pressure. In the direction of movement the first filter hose row is neutralised, while the second row is flushed from the clean air side. The third row is likewise neutralised. This results in a draught delay, which is necessary in order to allow the dislodged dust to fall into the discharge. The dust is discharged by a tried-and-tested drag conveyor with a downstream cellular wheel sluice. The return air pipes are provided with fire protection flaps and switching devices for exhaust air operation. The filter housing has been tested for resistance to pressure surges. Standard safety devices include likewise tested explosion pressure relief devices, fire extinguishing systems, mechanical and thermal monitoring systems as well as pressure-surge-resistant and flameproof cellular wheel sluices. The transport fan is arranged on the clean air side and is not exposed to swarf and dust. Hence, the conditions of a dust explosion zone do not prevail in the transport fan. RSV/RXV filter This series essentially differs from the RS/RX series in that its fans are arranged on the clean air side. RSV/RXV filters are suitable only for vacuum pressure operation. The capacity range extends from approx. 20,000 - 300,000 m³/h. The filter hoses are likewise cleaned off using the material-preserving low-pressure purge-air system.

With high-quality filter tubes and PTFE diaphragms. Paint dust filters Wet painting also results in overspray. Overspray is the solid portion of the paint that is not taken up by the workpiece. According to the purpose of use, the overspray is moist and sticky immediately after release. It is captured by the exhaust air stream in the spray booth and fed to a filter. This can be, for example, a baffle plate filter, paper filter, fleece filter, glass fibre filter or also combinations of these. The adhesive effect causes the paint particles to adhere to the contact surfaces of the respective filter medium, as a result of which a good degree of separation is achieved. However, all these filters are storage filters, i.e. the filters clog up more and more during operation and cannot be regenerated. A filter exchange becomes necessary if the exhaust air rate of the spray booth falls below the minimum. This can be very time-consuming under certain circumstances and the work process must be interrupted in order to do it. To make things worse, not only must the filtered and bound paint residues be disposed of, but also the actual filter materials. Such tooling times are not justifiable for automatic, continuous or multi-layer painting processes. Continuous procedures such as automatically cleaned filters are likewise required for this. The humidity and the adhesiveness of the particles to be filtered are thereby the problem. In order to solve this problem, the paint particles should be relieved of their adhesive capability as far as possible whilst still inside the paint booth. Our patented ‘RTS-Rotation’ system is outstandingly well suited for this. The system is comprised of slowly rotating brush rollers, which take up the adhesive paint particles on the surface of the bristles and allow them to dry there. The bristles are automatically regenerated at pre-specified time intervals by combing devices that swing in at the rear of the brush rollers. The dislodged paint residues can then be removed and disposed of either manually during work breaks or automatically during operation. The degree of separation of this system is, however, insufficient to satisfy the environmental protection requirements concerning residual dust content in the exhaust air. A further filter stage is necessary for that. It must be assumed that the paint particles arriving here are to a certain extent still damp and sticky. For this we use special paint dust filters with high-quality filter tubes with PTFE diaphragms. If necessary, precoating agents (auxiliary dust) are used in order to neutralise the adhesive capability of the particles and to keep the dust layer on the filter elements permeable to air. The precoating agent is injected into the raw air pipe by means of special dosing units. The filter tubes are cleaned by means of compressed air impulse cleaning. The use of this technology requires special know-how. We have had the appropriate experience for almost ten years. The implemented plants have capacities ranging from 5,000 to 90,000 m³ /h. Because of the large number of different paint systems, individual experiments are usually necessary in our pilot plant in order to find the correct solution for the individual case.

Flare Systems Since the 1980’s, key staff of Europem have been responsible for the design, fabrication, installation, commissioning and maintenance of numerous flare systems including some of the most stringent and demanding applications. Europem’s extensive experience in flare design has resulted in a comprehensive range of elevated and ground flare systems and ancillaries to cover the needs of all major industries. Low and High Pressure Utility (Pipe) Flares Air assisted Flares Steam assisted Flares Gas assisted Flares Sonic Flares Speciality flares for Ammonia, H2S, LNG and lean waste gas Mobile Flare systems – for purchase, lease or rental Venturi Flame Shields protecting the flare from flame lick and improving combustion efficiency Ancillaries such as pilots, ignition systems, pilot detection, KO drums, water seals, molecular seals and conical purge seals Supporting structures including derricks, demountable riser type derricks, guy wire support systems, plus self supporting Flares Enclosed ground flares with single or multiple burners Temperature controlled combustors and thermal oxidisers. Europem aims to be a long term partner to all our clients and provides full aftermarket support for all operation, maintenance and intervention requirements. We can also provide for the inspection, maintenance, refurbishment and replacement of any flare system or components and can supply in some cases, rental flares during maintenance interventions.

By a highly intensive cooling, which is integrated in the crank casing a continous running at max 10 bar is ensured. In comparison with other compressed air compressors the big filter surface of the suction filter with 10 µ guarantees a long lifetime and an optimal suction behaviour. Due to the missing of external pipes the compressed air compressors of the range Marathon, are espescially compact. Advantages extreme long running life maintenance free low noise level continuous running

The device is used as hand pistol for riveting, welding and edge folding of plastic parts. The weight of the welding pistol is lower than 900 g. The optimum design of the welding pistol allow for a particularly comfortable handling. The titanium booster ensures a maximum safety of the converter and optimal adaptation to the various tools. Advantages of the SPK version: By the permanent cooling of the piezo-ceramic transducer and the titanium booster an extremely high performance period can be achieved. The cooling air pipe is integrated in the HF control cable. Advantage: No disturbing connective elements for a separate pipe, and the cooling air is led directly to the spots to be cooled.. For this the grip is fitted with an exhaust port for the cooling air, into which cooling pipes can be simply screwed in. In this version the generator is also cooled by an incorporated ventilator. As an option we can offer hand welding devices with energy control

Application as inline armature with venting and breather valve function for vessels, used preferably for installations in pipes. The exhaust air is carried away via a pipe. The ventilation is also effected via a pipe, which is preferably used to carry inert gas. Functions the same as KITO® VD/o3-… (type sheet F 18 N).

Range of application fiber optic transmission systems in public telecommunication networks, service networks and dedicated networks if connected to the public communication network, installation in cable duct systems, over bridges and overpasses, inside protective PE pipes (including air blowing installation).

Range of application fiber optic transmission systems in public telecommunication networks, service networks and dedicated networks if connected to the public communication network, installation in cable duct systems, over bridges and overpasses, inside protective PE pipes (including air blowing installation).

Range of application fiber optic transmission systems in public telecommunication networks, service networks and dedicated networks if connected to the public communication network, installation in cable duct systems, over bridges and overpasses, inside protective PE pipes (including air blowing installation).

Range of application fiber optic transmission systems in public telecommunication networks, service networks and dedicated networks if connected to the public communication network, installation between buildings of different types, installation in communication lines, on power lines and automatic control lines of electric railways at points with a maximum electric field potential of up to 12 kV, inside protective PE pipes (including air blowing installation), in swamps, in cable trays, in ducts, tunnels, sewers, on bridges and overpasses.

Range of application fiber optic transmission systems in public telecommunication networks, service networks and dedicated networks if connected to the public communication network, installation between buildings of different types, installation in communication lines, on power lines and automatic control lines of electric railways at points with a maximum electric field potential of up to 12 kV, inside protective PE pipes (including air blowing installation), in swamps, in cable trays, in ducts, tunnels, sewers, on bridges and overpasses.

Range of application fiber optic transmission systems in public telecommunication networks, service networks and dedicated networks if connected to the public communication network, installation between buildings of different types, installation in communication lines, on power lines and automatic control lines of electric railways at points with a maximum electric field potential of up to 12 kV, inside protective PE pipes (including air blowing installation), in swamps, in cable trays, in ducts, tunnels, sewers, on bridges and overpasses.

Range of application fiber optic transmission systems in public telecommunication networks, service networks and dedicated networks if connected to the public communication network, installation between buildings of different types, installation in communication lines, on power lines and automatic control lines of electric railways at points with a maximum electric field potential of up to 12 kV, inside protective PE pipes (including air blowing installation), in swamps, in cable trays, in ducts, tunnels, sewers, on bridges and overpasses, as well as winding, connecting and attaching to external load bearing power elements (ropes, wires, etc.) at points with a maximum electric field potential up to 12 kV.

Range of application fiber optic transmission systems in public telecommunication networks, service networks and dedicated networks if connected to the public communication network, installation between buildings of different types, installation in communication lines, on power lines and automatic control lines of electric railways at points with a maximum electric field potential of up to 12 kV, inside protective PE pipes (including air blowing installation), in swamps, in cable trays, in ducts, tunnels, sewers, on bridges and overpasses, as well as winding, connecting and attaching to external load bearing power elements (ropes, wires, etc.) at points with a maximum electric field potential up to 12 kV.

Avantair is unique in the marketplace as it uses heat pipe technology. This advanced air-to-air cooler is particularly recommended for challenging environments like offshore and desert locations.