Plate heaters - Import export

Square cartridge heaters are used where much power has to be installed near the surface of a tool, e.g. in cutting knives, sealing stations or hot plates. With a soft, malleable condition in stainless steel or nickel sheath square cartridge heaters can easily be pressed into common milled rectangular grooves. Apart from the advantageous heat transfer over ¾ of the sheath, it is not necessary to cement or cast in the heater which is imperative for round cartridge heaters. Unlike tubular heaters which are also available in square sections (see chapter Flexible Heating Pipes), the square cartridge heaters have the termination on one side and can be loaded with 16W/cm² (2.5W/in²) due to their special inside construction.

Polyester heaters also referred to as Polyester film heaters or Polyester foil heaters consist of an electrically conductive ink between two insulating respectively carrier layers of polyester. With a maximum size of 600 x 1000 mm, their average height is only 0.2 mm. As the picture examples show, practically any shape and type of cut-out is possible. Polyester foil heaters are resistant to permanent temperatures of up to 90°C (max. 100°C for short periods). It is generally not possible to predict which temperature a Polyester heating element will reach in the application, as there are extremely many influencing factors. These include not only the power, but also the mass and type of goods to be heated, the ambient temperature, air currents, the type of mounting and, of course, the control technology. Typical applications for Polyester heaters are e.g. cup warmers in coffee machines, mirror heaters, plate heat exchangers, flat applications with a target temperature below 90°C.

HotCoils have a larger cross-sectional area and are thus capable of greater power than MicroCoils. For this reason they are used in hot runners with adequate space and where high heat densities are required. Owing to the large number of variants and for cost reasons, the sheath material for HotCoils is stainless steel - the standard for the market and thus also for Freek. HotCoils are large enough that thermocouples can be integrated into them. Our standard here is Type J (Fe-CuNi; red/blue), while Types J and K are also available conforming to the IEC and ANSI standards (see colour codes). Since the measurement point of a built-in temperature sensor is situated in the heater and never where the heat is actually required, a HotCoil with a thermocouple makes particular sense where the application allows the use of larger processing (temperature) windows or where the installation location or the design requires protection against overheating.

Advantages of Heating Plates with Square Cartridge Heaters: -> Simple plate manufacture due to rectangular groove geometry, no deep-hole boring -> Simple heater installation by bending and pressing along the plate surface -> Complex plate geometries with bores and openings -> Optimal heat transfer due to 75% surface contact -> No casting with heat conductive compound -> Uniform temperature profiles due to thermally optimized groove layouts/power distribution and utilization of insulation plates -> high process temperatures (up to 450°C in aluminium, up to 700°C in stainless steel) Example "Heated Stamp": D=100 mm out of tempered tool steel up to max. 700°C continuous temperature. Fitted with 2 Square Cartridge Heaters 1500 W/ 230 V, 4,5 x 4,5 mm x 600 mm, with 50 mm unheated at the termination end. Annealed and formable with a nickel sheath, resistant up to 850°C surface temperature. Connection by fibreglass insulated pure nickel high-temperature leads (max. 500°C)

CSN® copper and nickel are temperatureresistant connecting cables for internal wiring of electric household appliances such as hotplates, glass ceramic plates, grill appliances or storage heaters. In industrial applications CSN® Cables are preferably used for the wiring of heating elements, heating cartridges, tubular heaters, panel heaters, and quartz radiators. We manufacture these singlecore cables in cross sections up to 6 mm². Owing to their high temperature resistance up to 250 °C in the case of glass silk insulation and 600 °C in the case of mineral fibre insulation, these connecting cables meet the most demanding requirements.

Synchronized forming and cutting by tilting movable lower platen to 85 degrees Sheet ; pitched by double toothed chains and move on abrasion resistant slide plates; Precise heater control for upper and lower pan. Upper and lower Mold ; heats control by indivudial Thermoregulation device Fine adjustment for mold by electric drive. PLC for control the line operation and to supervise working parameters Non-stop working capacity with easy maintain mechanical system. Safety system ensured by sensors such as sheet sagging , pressure drop,door ajar situations Water and Heat balance measure sensors for mold which can be control by PLC system Energy analyzer which gives amount of the electric consumption Cutting adjustment possible by digital meter ,controlled by PLC. Plug asist motor and plug speeds all controlling by PLC suitable to put variotions of movement to plugs to plugs,start slow go fast end slow etc

Pyrolytic boron nitride is a grade of hexagonal boron nitride. It is produced by the chemical vapor deposition process to create its solid body and all the boron nitride crystals grow parallel to the surface on which the vapor is deposited.

Mechanically durable and thermally shock resistant, PBN/PG heaters are unaffected by vibration under most conditions and can be tailored to thermal gradients for specific requirements. With an ultra-fast response and low thermal mass, PBN/PG heaters demonstrate a power output of 35 watts/cm 2 (225 watts/in 2 ) and higher.Size customization, please let me know the use temperature, current and voltage. -Crystal growth (VGF, LEC Crucible) -Molecular Beam Epitaxy(MBE) Crucible -MOCVD Heater -PBN Infrared Window -Traveling Wave Tube (TWT) (PBN Support Rod) -PBN Coating Graphite -High temperature, vacuum equipment insulator

Planar ceramic heater oxygen sensors are subject to extreme conditions. A properly functioning oxygen sensor forms the basis for reliable engine operation and thus fuel economy, low pollutant emissions, and good exhaust gas values. Oxygen sensors with planar ceramic heater characteristics: ● Quick ignition time ● Good insulation performance ● Strong resistance to high temperature and poisoning ● Long lifetime ● Pump current switch type, conventional switch type, air-fuel ration type, and wide range type are available Appliaction: Plate Ceramic Heater Chip for Automobile / Oxygen Sensor

Planar ceramic heater oxygen sensors are subject to extreme conditions. A properly functioning oxygen sensor forms the basis for reliable engine operation and thus fuel economy, low pollutant emissions, and good exhaust gas values. Oxygen sensors with planar ceramic heater characteristics: ● Quick ignition time ● Good insulation performance ● Strong resistance to high temperature and poisoning ● Long lifetime ● Pump current switch type, conventional switch type, air-fuel ration type, and wide range type are available Appliaction: Plate Ceramic Heater for Automobile / Oxygen Sensor

Planar ceramic heater oxygen sensors are subject to extreme conditions. A properly functioning oxygen sensor forms the basis for reliable engine operation and thus fuel economy, low pollutant emissions, and good exhaust gas values. Oxygen sensors with planar ceramic heater characteristics: ● Quick ignition time ● Good insulation performance ● Strong resistance to high temperature and poisoning ● Long lifetime ● Pump current switch type, conventional switch type, air-fuel ration type, and wide range type are available Appliaction: Plate Ceramic Heater for Automobile / Oxygen Senser

Gufo HG gas fired heater is designed as an economic heating solution to be used in the winter gardens of restaurants, cafes, hotels and offices, smoking areas and terraces. Impact, moisture and wind resistant stainless steel chassis. Resistant to 1100 degrees and thermal shocks, having 98% heat conduction and aesthetic ceramic glass. With the low or high step burning system, the desired temperature comfort can be provided easily according to the temperature of the air. Built-in remote control for convenient and easy operation. Technical Features 1. Step Power 7 kW 2. Step Power 12,5 kW Heating Area 25-50 m² Natural Gas Consumption 1,3 m³/saat Recommend Hanging Height 2,2 m Natural Gas Pressure 20 - 55 mbar Gas Connector Diameter 1/2’’ Electric Voltage 220-240 V

Aluminum reflectors are used for high luminous efficiency. It provides many years of trouble-free operation without the need for special maintenance programs. For your safety, there is a safety system with a buzzer against a malfunction. Usage areas: Factories, Workplaces, Warehouses, Hangars, Service Stations, Mosques, Sanctuary, Farms, Outdoor and other places. TECHNICAL FEATURES Product Code - 1st Power - 2nd Power -NG Consumption -Hanging Height**(H) ECO L5 - 6 kW - 11 kW - 1,15 m³/saat - 2,5 m ECO L10 - 11 kW - 18 kW - 1,90 m³/saat. - 3,5 m ECO L14 - 16 kW - 26 kW - 2,73 m³/saat - 4,5 m ECO L18 - 20 kW - 32,1 kW - 3,37 m³/saat - 5,0 m Natural Gas Pressure 20-55 mbar Gas Connector Diameter 1/2’’ Electric Voltage 220-240 V

Gufo GT is especially suitable for awnings and parasols with its asymmetric design that increases heating efficiency to high points. Gufo GT provides economic with a high radiation capacity via natural gas operated working principle. It is designed as low capacity and lightweight for the spaces with limited hanging height. TECHNICAL FEATURES Product Code Gufo GT 2 Gufo GT 4 1. Step Power 2 kW 4 kW 2. Step Power 4 kW 8 kW Heating Area 4-8 m² 8-16 m² Natural Gas Consumption 0,42 m³/saat 0,84 m³/saat Recommended Hanging Height**(H) 2,0 m Natural Gas Pressure 20-55 mbar

PRODUCT INFORMATION This machine is ideal for the single corner welding of PVC profiles between 30°- 180°. Enable the welding of all angles between 30°-180°infinitely adjustable All parameters such as melting and welding time, welding pressure are set independently Automatically start and finish the welding cycle Adjusting the heat between 0-300°C by means of the electronic thermostat Smooth welding operations for long profiles by means of rotating support arms Maintenance friendly, for example cleaning of the heater plate and changing of the Teflon is very easy by means of quick change system Practical adjustment of standardl (2 mm) or seamless (0.2 mm) welding options manually Standard equipped with height adjustable profile support arms on both side Clamping the profiles separately via foot pedal Saving of time by means of practical mold change feature Portable machine stand OPTIONAL ACCESSORIES Machine according to the profile height of 165 mm