COMPOSITION AND APPEARANCE Powder coating based on plaster, calcium carbonate, resin, and various additives. The paste obtained is white in color. SUBSTRUCTURES ADMITTED All types of plasterboard with or without insulation (glass wool, rock wool, polystyrene) with tapered edges and cardboard faces. COATINGS Printing undercoat for gypsum plasterboard. Plaster-based smoothing plaster. TECHNICAL SPECIFICATIONS - Setting time: 2 hours - Adhesion of the tape: > 1000 g - Cracking: no cracks up to 5 mm thick STORAGE 9 months in original unopened packaging protected from humidity APPLICATION Before treatment of the joints themselves, the panels must be filled between accidentally non-joined panels and various fillings. The application is done manually by "buttering" the thinned panels with a 10 or 15 cm coating knife and placing the strip. Then carry out a finishing pass, let dry and finish to mask the strip. Also mask the screw heads.
France
COMPOSITION AND APPEARANCE Powder coating based on plaster, calcium carbonate, resin, and various additives. The paste obtained is white in color. ADMITTED SUPPORTS All types of plasterboard with or without insulation with tapered edges and cardboard faces. COATINGS Plaster-based smoothing plaster. TECHNICAL SPECIFICATIONS - Setting time: 1/2 hour - Adhesion of the tape: > 1000 g - Cracking: no cracks up to 5 mm thick - Density: 0.9 - Reaction to fire: A1 STORAGE 9 months in original unopened packaging protected from humidity. SURFACE PREPARATION The plasterboards will be fixed in accordance with DTU 25.42. APPLICATION Before treatment of the joints themselves, the panels must be filled between accidentally non-joined panels and various fillings The application is done manually by "buttering" the thinned panels with a 10 or 15 cm coating knife and placing the strip. (Grinded face against the plaster).
Request for a quoteFrance
TECHNICAL PROPERTIES Primer filler for vertical surfaces or for use on ceilings made from poured concrete or pre-slabs. Decorating filler, for smoothing over. Smooth, matt finish. Odour-free. COMPOSITION AND APPEARANCE. Solvents : Water. Filler : Calcium carbonates. Additives : Dispersing agent, bactericidal fungicide. Thickeners : Cellulosic, polyacrylates. Binders : Acrylic dispersing agent. Density : 1.86. Dry matter : 75%. TECHNICAL PROPERTIES • Fire classification: A2-S1, d0 SUITABLE SURFACES Interior : ideal for covering bricks, brick tiles, cement breeze blocks, cinder blocks, de-bubbling pre-slabs, shuttered concrete, aerated concrete, for redecorating stippled walls or old damaged surfaces. APPLICATION. • The first coat should be levelled out using 60 cm scraper or skimmed with a rule. • After drying, the second coat should be smoothed with a scraper. • After allowing to set slightly, squeeze the filler at a slight angle using a clean scraper.
Request for a quoteFrance
TECHNICAL DEFINITION SEMIN AIRLESS 3 IN 1 is an indoor filler that can be used as an Airless spray. It provides an even appeareance without smoothing, has great coverage and a deep matt finish. It combines 3 actions : underlayer, filler and finish. COMPOSITION AND APPEARANCE Acrylic emulsion resin, mineral content, cellulose derivates, preservation agent and other additives. The resulting paste is a bright white colour and its consistency is adapted to its airless application. TECHNICAL CHARACTERISTICS • Dry extract : 68% • Density : 1,76 • COV : <1g/l APPLICATION SEMIN AIRLESSS 3 IN 1 can be sprayed with all kinds of Airless machines adapted to srpraying coatings. Recommended nozzle : 627. For optimum results, we recommend following this method : • Spray a first layer of the coating about 300 to 400 g/m2, to show up the defects on the surface. Spray at a distance of about 80 cm from the relevant surface • Check over the surface carrefully
Request for a quoteFrance
TECHNICAL DEFINITION Levelling filler for vertical substrates and for use on ceilings for poured concrete or pre-cast slabs. Ideal for the preparation of pre-cast slabs, formwork concrete and for the renovation of textured finishes or fibreglass with a paint finish. TECHNICAL CHARACTERISTICS • Dry extract : 75% • Density : 1.86 • VOC content : less than 1g/l COMPOSITION AND APPEARANCE Water, calcium carbonate, dispersant, bactericide, fungicide, cellulosic fibres, polyacrylates, clays, acrylic dispersant. AMOUNT REQUIRED From 2 to 4 kg for the first coat. From 1.5 to 2 kg for the second coat. APPLICATION SEMIN AIRLESS EXTREM filler is sprayed using the Airless pump or rotor machine/Flat spray stator in 2 coats. The first coat must be levelled using a 60 cm blade or levelled with a straight edge. After drying, the second coat must be smoothed using a blade.
Request for a quote