Electrical supplies - Import export

KFE Special customer requirements Applications Overview Presses Machine Tools Automatization + Feeders Lifting Gear + Mobile Hydraulics Production Technology Special Machinery CAD Download Contact Electric Locking Unit The electric Locking Unit KFE is used as a stepless locking device on round rods and holds axial forces in both load directions without axial play. It is used where hydraulic or pneumatic solutions are not possible. The holding force is created by the proven spring-operated clamping system as it is used in SITEMA’s hydraulically or pneumatically operated Locking Units. At a drop of the control voltage or in case of failure of the electric supply, the Locking Unit KFE clamps automatically. Therefore, it is also suitable for use in safety relevant applications. To operate the Locking Unit KFE, a supply voltage of 24 V and a control signal for the input command “clamp/release” are sufficient. The Locking Unit is self-monitoring and provides output signals...

Mechanical Valve Actuator MVA Rod leaving clamping head Auto Bleeder Mechanical Safety Catcher KRM Electric Locking Unit KFE Special customer requirements Applications Overview Presses Machine Tools Automatization + Feeders Lifting Gear + Mobile Hydraulics Production Technology Special Machinery CAD Download Contact Electropneumatic module EPM The Electropneumatic Module EPM acts as interface between (electrical) power supply / control and a pneumatic SITEMA clamping head. All pneumatic SITEMA clamping heads with an operating pressure of up to 4 bar and an operating volume of up to 220 cm³ can be pneumatically controlled by the EPM. It is also possible to operate several clamping heads in parallel with one EPM. The EPM is controlled by a 24V supply and switching voltage. The outlet pressure which is required to open or keep open a pneumatic clamping head is controlled by a control signal. If the voltage fails or the input signal is switched off, the pressure is...

At locations without a fixed power supply, diesel generators are currently mainly used. The PowerCube was developed to ensure the power supply even without such a unit. The use with solar cells additionally offers the possibility to operate self-sufficient systems. * Flexible and versatile * High running time * Compensation of instable mains Features & Advantages * Display with charge status and load * Mains-independent power supply * Ambient temperature: 0°C to 40°C (up to 50°C with power loss) * Relative humidity 20% to 90% * Type of protection: IP21 * can be easily extended to a permanent power source with a solar panel via plug&play

Cold rolled strip is used in a variety of applications. It meets high demands on forming behaviour, dimensional tolerances and surface finish, which offers our customers decisive advantages! HFP cold rolled strip is ideally suited for all stamping, bending, drawing and deep drawing purposes. From ball bearing housings to roll cutting and punching strips, hose clamps, headlight reflectors, electrical equipment, office supplies and tubes to safety parts of all kinds, a wide variety of components can be manufactured for various industries. DC 01, DC 03, DC 04 according to DIN EN 10139 / mild steel - St 37/ special grades on request Depending on the customer's requirements, we supply treatment states from LG to C690.

Welding assembly

For special applications, individual high-pressure systems are required, which KAMAT can provide from the initial project idea to the turnkey installation, with 100% of the production taking place in-house. This also applies to electric high-pressure pumping units. Depending on the application, our customers can choose between different drives, power transmission components, PLC controls, measuring systems, data transmission, remote controls, pneumatic and electric valve controls, chassis and sound insulation equipment. Even the electrical units supplied on the base frame are fully operational and can be used directly by the customer. Electric units have the advantage of emission-free operation at extremely low noise levels. ATEX certified high pressure electric units can also be used in ATEX hazardous areas.

Double column wall mounted stand mixer/floor stand mixer Rigid stand for wall-mounting or floor stand for mixers from 100 kg. The stand consists of 2 u-shaped columns with a ball-borne support slide with a cantilever beam for the mixer. The double-column stand allows the processing of tank volumes up to 4 m3, depending on the tank dimensions. Mixer powers up to 75.0 kW and support loads up to 1,000 kg can be realized. Under these conditions, the stand can be equipped with all fast running or gear-reduced mixers and their matching agitator elements. The lift is done electrically by a lift drive and chain drive. The electric supply is guided through a laterally mounted energy chain. Customized solutions for instance a stand mixer with H foot or stand equipped with coaxial agitator type KRK are feasible.

WRW/SRW – Double column Double column wall mounted stand mixer/floor stand mixer Rigid stand for wall-mounting or floor stand for mixers from 100 kg. The stand consists of 2 u-shaped columns with a ball-borne support slide with a cantilever beam for the mixer. The double-column stand allows the processing of tank volumes up to 4 m3, depending on the tank dimensions. Mixer powers up to 75.0 kW and support loads up to 1,000 kg can be realized. Under these conditions, the stand can be equipped with all fast running or gear-reduced mixers and their matching agitator elements. The lift is done electrically by a lift drive and chain drive. The electric supply is guided through a laterally mounted energy chain. Customized solutions for instance a stand mixer with H foot or stand equipped with coaxial agitator type KRK are feasible.

The BaCo 1800 is a fully automated foil application and sealing machine, suitable for plastic, tin or glass containers. mobile base frame feed conveyor with feed control synchronised star wheel stand with receptacles for the containers as form parts adjustable outer ring for guiding containers through the machine sequence foil magazine for stackable pre-cut Ballerstaedt seals pneumatically driven foil dispenser with a precise, maintenance free 180° reverse gear for removing the seals from the magazine, applying them to the sealing edge and fixing them with a pre-sealer sealing station for closing the containers with regulation of the sealing temperature, pressure and time for optimal setting of the seal parameters, conductive, optional also inductive exit conveyor for the containers central height adjustment of the magazine plate to adjust it to the respective container height all-over protective coating control panel with electrical supply unit

Rigid stand with H-foot for tanks that range in volume from 100 l. Under these conditions, the stand can be equipped with all fast running or gear-reduced mixers and their matching mixing elements. Mixer powers from 0.37 kW to 7.5 kW and support loads up to 100 kg – by means of a reinforced stand loads up to 300 kg – can be realized. The agitator is positioned on a telescope sleeve that is moved via the spring-suspended lid connected to the stand. The lift is done by a geared hand-wheel or electric with a lift drive and chain drive. The mixer is positioned on a cantilever beam which is fixed to a support slide that is moved on the stand column. The electric or pneumatic supply is guided through a laterally mounted energy chain. The floor stand mixer SRW is available in two standard sizes that are particularly designed for the processing of exchangeable vessels such as drums and IBCs. Various tank sizes upon request.

Rigid stand for wall-mounting for tank volumes from 100 l. Mixer powers from 0.37 kW to 7.5 kW and support loads up to 100 kg can be realized. Under these conditions, the stand can be equipped with all fast running or gear-reduced mixers and their matching agitator elements. The lift is done by a geared hand-wheel or electric with a lift drive and chain drive. The mixer is positioned on a cantilever beam which is fixed to a support slide that is moved on the stand column. The electric or pneumatic supply is guided through a laterally mounted energy chain. The stand WRW is available in two standard sizes, thus enabling the processing of various tank sizes. The standard sizes are particularly designed for the processing of exchangeable vessels such as drums and IBCs.

WRW - Wall mounted stand mixer Rigid stand for wall-mounting for tank volumes from 100 l. Mixer powers from 0.37 kW to 7.5 kW and support loads up to 100 kg can be realized. Under these conditions, the stand can be equipped with all fast running or gear-reduced mixers and their matching agitator elements. The lift is done by a geared hand-wheel or electric with a lift drive and chain drive. The mixer is positioned on a cantilever beam which is fixed to a support slide that is moved on the stand column. The electric or pneumatic supply is guided through a laterally mounted energy chain. The stand WRW is available in two standard sizes, thus enabling the processing of various tank sizes. The standard sizes are particularly designed for the processing of exchangeable vessels such as drums and IBCs.

FRW - Mobile stand mixer Mobile stand with H-foot for tank volumes from 100 l. The mobility of the tripod is ensured by using castors and fixed castors. The tripod can be moved due to The lift is done by a geared hand-wheel or electric with a lift drive and chain drive. Mixer powers from 0.37 kW to 7.5 kW and support loads up to 100 kg can be realized (with ex-protection only realizable to a limited extend). Under these conditions, the stand can be equipped with all fast running or gear-reduced mixers and their matching mixing elements. The mixer is positioned on a cantilever beam which is fixed to a support slide that is moved on the stand column. The FRW is equipped with fixed and steerable wheels for mobility. The electric or pneumatic supply is guided through a laterally mounted energy chain. The mobile stand mixer FRW is available in two standard sizes that are particularly designed for the processing of exchangeable vessels such as drums and IBCs. Various tank sizes upon...

SRW - Floor stand mixer Rigid stand with H-foot for tanks that range in volume from 100 l. Under these conditions, the stand can be equipped with all fast running or gear-reduced mixers and their matching mixing elements. Mixer powers from 0.37 kW to 7.5 kW and support loads up to 100 kg - by means of a reinforced stand loads up to 300 kg - can be realized. The agitator is positioned on a telescope sleeve that is moved via the spring-suspended lid connected to the stand. The lift is done by a geared hand-wheel or electric with a lift drive and chain drive. The mixer is positioned on a cantilever beam which is fixed to a support slide that is moved on the stand column. The electric or pneumatic supply is guided through a laterally mounted energy chain. The floor stand mixer SRW is available in two standard sizes that are particularly designed for the processing of exchangeable vessels such as drums and IBCs. Various tank sizes upon request.

Mobile stand with H-foot for tank volumes from 100 l. The mobility of the tripod is ensured by using castors and fixed castors. The tripod can be moved due to The lift is done by a geared hand-wheel or electric with a lift drive and chain drive. Mixer powers from 0.37 kW to 7.5 kW and support loads up to 100 kg can be realized (with ex-protection only realizable to a limited extend). Under these conditions, the stand can be equipped with all fast running or gear-reduced mixers and their matching mixing elements. The mixer is positioned on a cantilever beam which is fixed to a support slide that is moved on the stand column. The FRW is equipped with fixed and steerable wheels for mobility. The electric or pneumatic supply is guided through a laterally mounted energy chain. The mobile stand mixer FRW is available in two standard sizes that are particularly designed for the processing of exchangeable vessels such as drums and IBCs. Various tank sizes upon request.

Your business card: The Orbital-Workstation — Electrical supply integrated for auxiliary equipment: 5 x 230 V, 10 A (not suitable for the power sour ce!) — 2 swivel castors, Ø 160 mm, with full lock — 2 trestle castors, Ø 280 mm — Pull-out cylinder bracket with fixing chain above the cylinder’s centre of gravity — High-quality powder-coated finish — Sturdy stainless steel work top, tilted — Platform for oxygen analyser — Fixing for bench vice with ‘V’ block — Holder for open weld head — Holder for manual hose package — Storage space for inverter, cooling unit, etc.

Workplace equipment and furnishings made of profile technology Slot: 5 - 10 INFORMATION SUPPLY Monitor arms and monitor holders VESA compatible, height adjustable, horizontally and vertically alignable Labelling clip: Labelling of profiles TOOL SUPPLY Cup holder: For placing a bottle or hanging a tool MATERIAL SUPPLY Grab containers: Provision of small parts on separation surface and selective pick-up Can be mounted by swivelling into the profile slot and onto the suspension profile and perforated plate optional adapter can also be swivelled horizontally in the profile groove Optional fixing option Highly visible marking field black, yellow, red, green, grey Tool hanger: Attachment of tools LIGHTING Magnifying luminaire D160 with articulated arm and dimmer fatigue-free and ergonomic work without irritating shadows electrostatic discharge version also available other colors/sizes on request

Elastic monolithic PU conveyor belts from BEHAbelt offer new fabrication possibilities. Due to the lack of traction layers joining by finger welding is no longer necessary, as the monolithic belt has a homogeneous design – even in the weld seam. The welding device HS from BEHAbelt is a simple, handy, reliable and costeffective tool for butt joining of monolithic belts. Depending on customer requirements, two versions are available with the joining table and heating paddle for max. belt widths up to 400 and up to 800 mm. The simple operation in combination with the intuitive production aids ­enables a repeatable and highquality connection of the belts. Optional adapter plates ensure precise positioning and clamping of the butt ends to be welded.

The BEHAbelt EErgo paddle welding tools were specially developed for the connection of PU and TPE profiles or flat belt strips. · Strong, fiberglassreinforced ergonomic housing. · Unique control panel for onehanded operation. · No adhesion of PU and TPE materials, thanks to Tefloncoated welding paddle.

The unique friction welding machine RS02 is the professional tool for the maintenance operator and also the fastest and most reliable way of welding belt profiles. Constantly good quality connections are produced in a few seconds with repeatable accuracy due to fixed welding parameters. Welding clamping jaws tuned to the respective profile ensure reliable clamping and perfect alignment of the profile. Thanks to its handy type of construction, the friction welding machine can even be used in narrow space conditions for comfortable welding. The ­recently developed battery version is now available to ensure unlimited freedom of motion.

Electric linear actuators from IAI are available as rod, slider and slide table types as well as with toothed belt drive. They are equipped with a stepper motor or servo motor and often already have a battery-free absolute encoder as standard. On request, they can also be supplied without an electric drive unit. The product range of linear actuators consists of the RoboCylinder series, which are characterised by high user-friendliness, simple programming as well as compact design. Their focus is on covering common customer requirements and are therefore relatively inexpensive. Electric slider type actuators and axes with toothed belt drive from the IntelligentActuators product line complete the product portfolio. They meet higher requirements than RoboCylinders in terms of payload, speed, acceleration and precision.

Challenge To execute a pilot project at the Energisa distribution network operator in Brazil within a tight time frame. The customer needed to install 23 kV outdoor circuit breakers with protection at a newly erected substation. Solution Tavrida Electric supplied the Rec25 with substation mounting kit to meet the deadline and satisfy the customer’s requirements in terms of protection. The mounting kit was subjected to comprehensive mechanical tests including overweighting, wind load and seismic impact with successful results.

For Example: Container 40 ft for outdoor installation for performance testing at combustion engines with all kinds of dynamometers. Depending on the kind of the installed dynamometer, external supply beyond electricity (e.g. for cooling water) will be required. Thanks to our mobile engine supports, there is no need of an overhead gantry crane or any other lifting device.

Vacuum lifting devices for flexible use with power unit and without electrical power supply. inquiry Example of use AERO-LIFT lifting devices with power unit Vacuum lifting device AERO 500/8L-Aggregat Vacuum lifting device with power unit for outdoor use. Handling of airtide wooden elements with a maximum dimension of 6000 x 520 mm and a weight of 500 kg. Vacuum lifting traverse carrying capacity 12.000 kg mains free lifting device to unload trucks in the outdoor area with a load bearing capacity of 12,000 kg. With integerated gasoline power supply for the vacuum generation.

The same excellent performance as our air tool! Operated with standard electric supply to households. Special long and slim barrel design suitable for narrow corners. Doubleinsulated motor does not need grounding. Free subhandle position best fot to your working situation.

- Operating voltage: 630 V AC/DC- Up to 12 A per pin - Operating current per contact max. 12 A - 4-pole - S-coded - Temperatur (fixed line): -25 bis +80°C - Temperatur (moving line): -20 bis +80°C - Material: PUR - Very compact connection for cables with wires up to 2.5 mm² - Reverse polarity protected, shockproof and vibration-proof - Made of high-quality plastic - Molded wires

Application The HMB Honing Rigs are designed for honing cylinder liners removed from the engine block with the corresponding mobile Hunger PHM Honing Machines. - Honing Rig Type HMB 340 is tailored to the Honing Machine Type HBM 340. - Honing Rig Type HMB 640 is tailored to the Honing Machine Type HBM 640. Features Rigid base structure including upright supporting tubes for mounting the mobile PHM Honing Machine. The liner to be honed is placed on top of a honing liquid reservoir which is slideably mounted on the base structure. The reservoir can be drawn out for ease of loading and unloading of the cylinder liner by means of a crane. An electric pump is provided to supply honing liquid to a spray nozzle. The spray nozzle is mounted on a magnetic base which can be attached to the frame tube to direct the honing liquid to the area to be honed.

The new portable HUNGER universal refacing machine UDM4E is a versatile machine offering a choice of modular components for refacing valves and valve seats as well as counterboring seat ring pockets and resurfacing the sealing surfaces on cylinder heads, cylinder liners and engine blocks of large diesel and gas engines. Key features: - No abrasive dust. A fast clean cut, - Compact and handy design - Modular add-on components provide a flexible solution for multiple projects - Powered by SELV (Safety Extra Low Voltage) to avoid risk of electrical shock - Power supply with universal AC input - Fast set-up time - Easy to use - The economical solution for both field and workshop use »Roundness, concentricity and surface finish of the refaced faces are within manufacturers’ specifications or even better«

Product information "UP6" The devices are protection class II compliant, voltage controlled, current-limited and continuously short-circuitproof, which means they offer a high level of operational safety combined with a long operational life. They also comply with the latest guidelines. Thanks to idle consumption of ≤ 300 mW and high efficiency at every power level, the units comply with the current threshold values of various energy efficiency programs, such as Energy Star, MEPS or ErP. Fits into all standard in-wall junction boxes, easy and invisible mounting, safe against andalism, many applications: Sanitary installations, security equipment, lighting, etc. Compact design Cost reductions by long lifetime and high efficiency