Technological laboratory - Import export

Shinano Kenshi offers the appropriate drives and controls for every application in medical technology or develops customer-specific solutions, even at the module or system level.

Application: Point dosing with highest volumetric accuracy - bead application with application speed adjustable to the web speed - encapsulation technology Areas of responsibility: - Electronic components - Semiconductor production - LCD/LED/OLED - Photovoltaics - Medical technology - Biochemistry - Laboratory - Optics and Photonics - SMD/SMT Technical Data: - True volumetric dosing - Retraction effect - Viscosity independent dosing - Easy cleaning - Inlet pressure independent dosing - Adjustable dosing flow - Pressure tight without valve - Dosing pressures up to 40 bar

In general, a Kapton film heater is always more expensive than a silicone heater or polyester heater. Where chemical resistance or the weight of the flexible heating element plays an important role, however, Kapton heaters are the ideal solution. The resistance of Kapton Polyimide to fungi, bacteria, ozone, weather, ageing and most chemicals, acids and solvents is very good, so that heating elements made of Polyimide (Kapton) are an ideal solution for many critical applications. Kapton foil heaters are also silicone-free and are characterised by an even heat distribution. The dielectric strength of a Polyimide film is very high and so the flexible Kapton (Polyimide) heater can be very thin. Due to the small thickness, the heat transfer to the component is improved and higher surface loads are possible. Typical applications for Kapton film heaters are: Laboratory technology, aircraft electronics, printers, diagnostic instruments, vacuum chambers, medical equipment and many more.

The 2-component positive displacement pump eco-DUO450, made by ViscoTec, allows many applications for the 2-component dispensing area. Possible fields of application are e.g. electronic components, semiconductor production, LCD/LED/OLED, photovoltaics, medical technology, biochemistry, laboratory, optics and photonics or SMD/SMT and many more. Application: - Dot dosing, with highest volumetric accuracy - bead application with application speed adjustable to the web speed - Potting technology Your advantages: - True volumetric dosing - Retreat effect - Viscosity-independent dosing - Easy cleaning - dosing independent of inlet pressure - Adjustable dosing flow - Pressure-tight without valve - Dosing pressures up to 40 bar

The latest generation of multifunctional YSTRAL PiloTec process equipment offers you the opportunity to use established production processes on a laboratory scale. Thanks to Conti-TDS technology, powder can be inducted, wetted and dispersed under vacuum, dust-free and in a single operation. Easy-to-use swappable tools enable operation using the innovative Multi-Z or Z-Inline process with high-precision multi-stage shear ring systems. Established procedures and a specific energy input independent of the batch size guarantee excellent and consistent results. These can be easily transferred to production scale - a safe scale-up to ystral plant construction. The modular design enables extension to the PiloTec-Plant process plant with ystral mixing technology, systems for handling powders and liquids, measuring technology and sensors, lifting stands as well as other modular components.

Medical technology: bone saws and blades for scissors If the cutting gap has to be aligned with the laser cutting of 0.07 mm, we are able to hear the smallest contours and thus filigree deeds for and a bone saw. What used to be lavishly packaged and wire-cut is now "simply" laser, and faster. Alternatively, we also cut blanks for blades, scissors, tweezers, other surgical instruments or medical instruments for endoscopy, dental and laboratory technology.

Over the last few years, we at EP-E have designed and introduced a series of primary standards for gases, designed for use in calibration laboratories. As a technology partner of the Physikalisch-Technische Bundesanstalt (PTB) in Braunschweig, our solutions are based on the highest standards. The EP gas bell plungers generate a volume flow which is traceable to the SI units length and time. The pistons are driven by a stepper motor via a spindle. In the initial state one piston is fully retracted and the other fully extended. The volume flow can be set with high precision via the piston cross section and the travel speed. At the end of the calibration process, both pistons are in the opposite position to the initial position. The calibration device is preferably operated with air, which can be supplied with up to 6 bar. The EP gas bell pistons convince by highest measuring accuracy up to 0.15% (k=2).

Over the last few years, we at EP-E have designed and introduced a range of primary standards designed for use in calibration laboratories. As a technology partner of the Physikalisch-Technische Bundesanstalt (PTB) in Braunschweig, Germany, our solutions are based on the highest standards. The EP gas bell plungers generate a volume flow which is traceable to the SI units length and time. The pistons are driven by a stepper motor via a spindle. In the initial state one piston is fully retracted and the other fully extended. The volume flow can be set with high precision via the piston cross section and the travel speed. At the end of the calibration process, both pistons are in the opposite position to the initial position.

A press for all processes Beside the pressing systems for industrial production, Siempelkamp manufactures laboratory press systems – both “try-out” presses for laboratoryscale tests with a starting pressing force of 150 t as well as presses for “fullscale testing”. The laboratory press systems are designed for maximum exibility. With it, all processes of composite production can be investigated. For example, it can be investigated whether press technology is an economic alternative for “autoclave” processes. All processes SMC with glass ber or carbon ber RTM PCM Organo-sheet consolidation Thermoplast forming Hybrid forming Integrated molding and joining of hybrid materials All control methods Force control with position monitoring Position control with force monitoring Each process step can be individually dened and programmed: All relevant process data are recorded and displayed.