Thinning - Import export

The SMS thin film evaporator type HYVAP serves the increasing demand of the pharmaceutical industry for continuous concentration of heat sensitive, viscous and fouling products. Hygienic design for the pharmaceutical industry The HYVAP is a horizontal thin film evaporator that allows easy access and inspection of the interior and controlled and reliable CIP cleaning. The technology of the HYVAP combines the proven advantages of our conventional horizontal thin film evaporators DKH with the following new features: • Cantilever rotor design • Comfortable rotor extraction • No bearing in product space • Mechanical seal in hygienic design • Electro-polished surfaces • Sight glasses for inspection during operation The new HYVAP DZH offers the hygienic design that meets current GMP requirements. The evaporator sizes range from 0.1 m2 for laboratory to 2.0 m2 for industrial applications. LP steam as well as hot water can be applied as heating media.

The vertical thin film dryer consists of a cylindrical, vertically arranged body with heating jacket and a rotor inside. The rotor is equipped with rows of pendulum blades all over the length of the dryer. The hinged blades spread the wet feed product in a thin product layer over the heated wall and mix the product layer material intensively. Therefore the volatile components evaporate continuously from the product layer with high evaporation rates. The hinged blades are designed with a minimum gap to prevent fouling of the heating surface by product, but are never in contact with the heated wall. The product enters the dryer at its top. The evaporation starts after heating to the boiling point. In the slurry zone first solids are formed and with advancing evaporation of the volatiles and continued shearing by the hinged blades the paste breaks up to powder. The final solid product is discharged by gravity at the bottom of the dryer via a suitable air lock.

Filmtruder and Viscon processors are specialized in the concentration, purification and devolatilization of products with viscosities up to 10,000 Pa (s) and are characterized by the following properties: Agitated thin film processing Unequaled surface renewal, resulting in the lowest residual volatile content Typically no stripping agents required Large free vapour volume compared to product hold-up, allowing very high volatile removal in one stage A successful thin film processing system consists of the right processor design integrated with properly engineered subsystems. SMS can provide a complete system, including installation and start-up services, or full engineering and design documentation to allow you to add the necessary subsystems for our thin film processor.

For the thermal separation of a mixture a thin film is produced at the heated wall of a cylindrical or conical evaporator. A distribution ring on the rotor distributes the liquid evenly across the periphery. Then, the blades fitted at the rotor spread the liquid as a thin film of min. 0.5 mm over the heat transfer surface. The model concept for the flow in the thin film evaporator assumes that prior to each rotor blade a bow wave is formed. In the gap between the rotor blade and the heating surface, fluid is supplied from the bow wave of a highly turbulent area with intense heat and mass transport. This results in a good heat transfer performance even with viscous products. In addition, the formation of deposits is avoided and the intensive mixing also protects temperature-sensitive products from overheating.

Advanced, Affordable Rate Control for Single or Multiple Layers Now get everything you want in a thin film deposition controller for single and multiple-layer processes. The XTC/3 with patented ModeLock provides proven mode hop prevention for consistent quality. With the XTC/3 Thin Film Deposition Controller, you get highly accurate control of deposition rate and thickness, the capacity for virtually any number of layers, easy installation, and extremely high reliability to ensure productivity. INFICON, the global leader in thin film deposition control, now offers an instrument with a remarkably low cost of ownership for unprecedented value. Whether your control needs reflect production or research and development use, you will find a precise match in the INFICON XTC/3. Worldwide INFICON Support No matter where you are, you get fast answers, attentive service, and maximum uptime. With offices around the world, INFICON is the only manufacturer of thin film deposition...

The SQM-160 uses proven INFICON quartz crystal sensor technology to measure rate and thickness in thin film deposition processes. Two sensor inputs are standard and four additional sensor inputs are optional. Two recorder outputs provide analog rate and thickness signals. Sensor inputs can be assigned to different materials, averaged for accurate deposition control in large systems, or configured for a dual sensor. The rate sampling mode allows a shuttered sensor to extend sensor life in high rate processes. Rate displays of 0.1Å/s or 0.01Å/s are user selectable. In addition, Frequency or Mass displays can be selected. Four relay outputs allow the SQM-160 to control source or sensor shutters, signal time and thickness setpoints, and signal crystal failure. Digital inputs allow external signals to start/stop and zero readings. Standard: RS-232; Optional: USB or Ethernet Standard: RS-232; Optional: USB or Ethernet Class 1 equipment, 73/72/EEC LVD, 89/336/EEC ECD Class 1...

SIMPLE OPERATION FOR MANY APPLICATIONS STM-2XM is a two channel rate/thickness monitor that combines high accuracy with flexible programming and easy operation at an affordable price. STM-2XM is equipped with five operation modes to accommodate processes from simple to complex. For example, use simple mode to monitor just one single sensor for the simplest process or use alloy mode for codeposition monitoring. Independent mode allows STM-2XM to function as two completely separate monitors. Two sensor inputs allow for the use of two single or one dual quartz crystal sensor. 10 measurements are taken per second while achieving a resolution of 0.037 Å per measurement (density of 1). FEATURE PACKED STM-2XM has eight programmable digital inputs, eight programmable digital outputs, and four analog outputs allowing for a level of integration usually reserved for more expensive instruments. Programmable features include shutter delay, time/power monitoring, and rate sampling. Use...

SMALL IN SIZE AND PRICE, BIG IN PERFORMANCE STM-2 combines the simplicity of USB connectivity with the accuracy of a precision measurement engine, all in a compact, inexpensive package. The size and simplicity of STM-2 help make setup and operation easy and efficient. SUPERIOR PERFORMANCE STM-2 is the most accurate USB powered thin film monitor in the industry. Ten measurements are taken per second while achieving a resolution of 0.037 Å per measurement (density of 1). EASY AND FLEXIBLE INSTALLATION STM-2 comes with everything you need to connect your QCM sensor/feedthrough to a Windows® PC. Simply connect the included BNC cable from the feedthrough to STM-2, then connect the STM-2 to your PC using a standard mini USB cable (included). No external oscillator or power supply is required. STM-2 features an internal oscillator that allows for simple and cost effective installation when STM-2 is located within 1 m (40 in.) of the quartz crystal. A standard INFICON® oscillator...

LOW-COST DEPOSITION CONTROL ON A PCI EXPRESS CARD The IQM-233 PCI Express card turns your PC into a thin film deposition controller. This INFICON designed and manufactured product is the ideal choice for system OEMs, or anyone wishing to incorporate a thin film deposition controller into an existing PC or PLC controlled system. Installation is simple—all you need is an unoccupied PCI Express slot. IQM-233 is available to fit in standard or small form factor PC towers. UNPARALLELED FEATURES The IQM-233 features three QCM sensor inputs and three source outputs on each card. Up to two IQM-233 cards can be installed in a single PC (requires optional IQS-233 software), giving you a maximum of six sensor inputs and six source outputs. Only INFICON offers this level of flexibility in a fully integrated PC controlled QCM controller. IQM-233 is compatible with INFICON oscillator IPN 782-900-010, so replacing an SQM-242 card does not require a new oscillator. It is also compatible with...

Highly Accurate Sequential or Codeposition Control With advanced electronics, an improved display, and a very affordable price, the INFICON SQC-310 Series gives you features not found on competitors' thin film controllers. And you can choose the ideal model for your application: sequential deposition (SQC-310) or codeposition (SQC-310C).

The Best Measurement Precision Possible for OLED Applications Cygnus 2 Thin Film Deposition Controller provides exceptional value by combining the proven performance of INFICON thin film controllers with unique features, all designed for you to achieve the most from your OLED process. Cygnus 2 uses our ModeLock frequency measurement system to provide stable, high-resolution rate and thickness measurement with an industry-leading rate resolution of .00433 Å/s every 1/10 second. No other quartz crystal controller has the performance, quality, and features of Cygnus 2, allowing you to make excellence repeatable. 1 Å for 0 to 9.999 kÅ 10 Å for 10.00 to 99.99 kÅ 100 Å for 100.0 to 999.9 kÅ 1 kÅ for 1000 to 9999 kÅ 0.001 for 0 to 9.999 Å/s 0.01 for 0 to 99.99 Å/s 0.1 for 100 to 999.9 Å/s 100 – 230 V (ac) +/- 15% 50 / 60 Hz +/- 3 Hz (1) Tooling/density = 100/1, fundamental frequency = 6 MHz (2) Varies according to process; figures reflect typical accuracy (3) Maximum configuration of...

MAKING EXCELLENCE REPEATABLE Feature-Rich IC6 Provides the Best Measurement Precision Possible The IC6 Thin Film Deposition Controller provides exceptional value by combining the proven performance of INFICON thin film controllers with unique features, all designed for you to achieve the most from your deposition process. The IC6 uses our ModeLock frequency measurement system to provide stable, high-resolution rate and thickness measurement with an industry-leading rate resolution of 0.00433 Å/s every 1/10 second. No other quartz crystal controller has the performance, quality, and features of the IC6, allowing you to make excellence repeatable. 1 Å for 0 to 9.999 kÅ 10 Å for 10.00 to 99.99 kÅ 100 Å for 100.0 to 999.9 kÅ 1 kÅ for 1000 to 9999 kÅ 0.001 for 0 to 9.999 Å/s if rate filter time setting is 10 seconds or greater 0.01 for 0 to 99.99 Å/s 0.1 for 100 to 999.9 Å/s 100 – 230 V (ac) +/- 15% 50 / 60 Hz +/- 3 Hz (1) Tooling/density = 100/1, fundamental frequency = 6 MHz (2)...

Metallurgic Powder

Rolling and friction bearing lubrication, even at high temperatures Lubrication for bearings with contact to cleaning agents or disinfectants For mechanical units such as levers, joints and hinges, also under strong water effect Advantages and benefits NSF H1 registered (OKS 480 & OKS 481) High shear stability prevents thinning out of the grease under extreme mechanical loads such as during vibrations Excellent wear protection and very good high-pressure properties The calcium sulphonate complex soap ensures excellent water resistance and very good corrosion protection Broad temperature application range (-30°C to +160°C) High temperature and oxidation stability through fully synthetic base oil Very high resistance to water-alkaline or acidic disinfectants and cleaning agents MOSH/MOAH-free

BIEGLO offers polyimide tubes with inner diameters starting from 2mm and going down to 100 micron. Our polyimide tubing are mainly used in the medical industry for catheters or neurovascular applications. Dexnyl polyimde tubings are extruded from thermoplastic polyimides and offer excellent pushability and tractability as well as ultra-smooth surface and transparency. USP class VI (USP 6) compliance is of course a given.

Smart embroidery is one of the most well-known technologies to add functions to and integrate them in textiles. Thus, we produce intelligent textiles with our special CNC wire laying technology. Potential applications include: > textile-based electrodes > flexible antennas > textile sensors > medical devices reliant on electromagnetic coils

Our speciality are thin-walled pipe-bends with large bending radius, especially for pneumatic conveying systems. The pipe-bends are cold-bent without any pleats on CNC-mandrel machines. Our quality management generally guarantees: welded seam smoothed or shaved (DIN 11 850 resp. DIN 17 457) absolutely wrinkle-free, no start-up bulges no scratching or scoring extremely low ovality visually aesthetic surface leg extension each side deburred sawing edges

These extremely long and thin panes require special suction systems. Heavydrive® offers these suction systems in a wide range of sizes and loading capacities.

Medium-volatile universal thinner with high dissolving power. Other sizes available on request

Turpentine substitute is a solvent for diluting oil and synthetic resin-based paints. Other sizes available on request

Medium- volatile universal thinner with high dissolving power. Other sizes available on request

Our elegant tie is perfect for sophisticated, fashion-conscious men. It is made of 100% fine microfiber, which has been carefully woven and handcrafted, making it particularly durable and resistant. With tasteful measurements of 150 x 7 cm, it perfectly adapts to any collar size and ensures a polished and stylish look. Wear these exquisite ties for everyday business or special occasions and stand out from the crowd. The tie offered here has an excellent price-performance ratio. The classic accessories from Tie Solution are a must-have for every office, celebration, or as corporate items with a logo. Convince yourself of our exclusivity. We are happy to produce customized ties for you starting from just 50 pieces. Can be personalized.

The slimline probe LMK 306 with ceramic sensor has been especially designed for the continuous level measurement at confined space conditions. Permissible media are clean or slightly contaminated water and thin fluids. Different cable sheath materials are available in order to achieve maximum media compatibility. Features: — nominal pressure: 0 ... 6 mH2O up to 0 ... 200 mH2O — accuracy: 0.5 % FSO — diameter 17 mm — excellent long term stability — suitable for hydrostatic level measurement e.g. 3/4" pipes — excellent linearity Optional Features: — different cable materials — customer specific versions e.g. special pressure ranges Preferred areas of use: — level measurement at confined space conditions — ground water monitoring — depth or level measurement in wells — drinking water abstraction — level measurement in open and closed tanks

The slimline probe LMP 305 with silicon stainless steel sensor is designed for continous level measurement in confined space conditions. Permissible media are clean or waste water and thin fluids. A piezoresistiv stainless steel sensor with low thermal error, an excellent linearity and a long term stability, is basis of LMP 305. Features: — nominal pressure: 0 ... 1 mH2O up to 0 ... 250 mH2O — accuracy: 0,35 % (opt. 0,25 %) FSO — diameter 19 mm for cramped areas e.g. 1" observation well — small thermal effect — excellent linearity — excellent long term stability Optional Features: — different kinds of cable — customer specific versions e.g. special pressure ranges

The pressure transmitter DMK 351P has been designed for measuring small system pressure in the food industry and chemical industry. The DMK 351P is based on an own-developed capacitive ceramic sensor element. It features high overpressure resistance and high resistance against most of aggressive media. A variety of different process and electrical connections and an intrinsically safe version complete the range of possibilities. Features: — nominal pressure: 0 ... 40 mbar up to 0 ... 20 bar — accuracy: 0,35 % (opt. 0,25 %) FSO — hygienic version — high overpressure capability — several process connections (G1" cone, Clamp, dairy pipe, etc.) (G 1/2, dairy pipe, clamp, etc.) Optional Features: — IS-Version Ex ia = intrinsically for gases and dusts — diaphragm AI2O3 99.9 % — customer specific versions e.g. special pressure ranges

The industrial pressure transmitter DMK 331 with ceramic sensor has been especially designed for pasty, polluted or aggressive media and for oxygen applications at low pressure range. As with all industrial pressure transmitters made by BD\SENSORS, you may choose between various electrical and mechanical connections also on DMK 331. Features: — nominal pressure: 0 ... 400 mbar up to 0 ... 600 bar — accuracy: 0.5 % FSO — pressure port G 1/2" flush for pasty and polluted media — pressure port G 1/2" open port PVDF for aggressive media Optional Features: — IS-Version Ex ia = intrinsically safe for gases and dusts — SIL 2 according to IEC 61508 / IEC 61511 — food compatible oil filling with FDA approval — cooling element for media temperatures up to 300 °C — customer specific versions

The precision pressure transmitter DMP 334i is a consistent further development of the approved industrial pressure transmitter DMP 334. Basic element is a thinfilm sensor which is welded with the pressure port. The integrated digital electronics compensates actively sensor specific deviations like non-linearity and thermal error. It is therefore possible to offer a high pressure transmitter with excellent metrological qualities. Nominal pressure — from 0 ... 600 bar up to 0 ... 2200 bar — accuracy: 0.2 % FSO — welded pressure sensor — turn-down 1:10 — excellent accuracy — robust and long-term stable Optional features — communication interface for adjusting offset, span and damping — pressure port M20 x 1.5 or 9/16 UNF — different kinds of electrical connections Preferred areas of use are — Plant and mechanical engineering —Utility vehicles and mobile hydraulics

SMS offers sludge drying systems with horizontal thin film dryers for treatment of sludge from municipal as well as from industrial waste water treatment plants. Variations of this sludge treatment process are: Pre-drying up to 35 to 50 % dry solid content before incineration in fluidized bed incinerators 65 to 75 % dry solid content before combined incineration with garbage, composting or landfill Full drying up to 85 to 95 % before thermal utilization as bio-fuel for cement kilns, coal fired power stations, pyrolysis, gasification or other conversion processes before composting and agricultural usage as fertilizer and for soil reclamation In all these drying processes the thin film dryer is the first choice.

The wet product fed through the inlet nozzle is picked up by the rotor blades, applied on the hot wall and simultaneously conveyed towards the outlet nozzle at the opposite end of the body. The generated vapours are streaming counter-currently to the product flow and are leaving the dryer close to the feed nozzle. Evaporating and conveying capacity are adapted by the right rotor blade arrangement. Entrained particles from the dry zone are removed in the wet zone. Moisture levels of less than 1 % can be achieved. The residence time of the product is typically between 5 and 15 minutes. The outstanding heat transfer rate for hot solid products enables cooling of large amounts of solids in a compact machine compared to usually used cooling screws and without cooling air.In product melting like the melting of urea, the particles are heated up and molten inside the dryer. The melt can be mixed with other liquid and solid additives to improve the properties of the final products.