Coated sheets - Import export

Our Infrared ovens can be produced as conveyor belt tunnel or internal return (U) type. Our ovens have andirect heating system with radiation heat transfer. They are used due to the cure flat shaped parts after wet or powder coating paint applications. They are preferred because they can cure the paint three times faster than the convectional type ovens. They can be produced with natural gas or lamp type infrareds. The inner surfaces of our ovens’ panels are produced with a galvanizedor stainless steel sheets and the outer surfaces are produced with galvanized sheet steel coated with electrostatic powder paint. Considering the application temperature, the required thicknesses determined and rock wool or glass wool is used for insulation.

Our continuous type ovens can be produced as belt tunnel type, internal return (U) type or with span conveyor. Our ovens have the indirect heating thermo-block system with convection heat transfer. It can be manufactured according to power supply sources like electricity, gas or liquid fuel. The inner surfaces of our ovens’ panels are produced with galvanized sheet and the outer surfaces are produced with galvanized sheet steel coated with electrostatic powder paint. Considering the application temperature, the required thickness (usually 160 mm) is determined and only rock wool is used for insulation. Air curtains in the furnace are placed inlet and outlet of the oven to minimize heat loss while increasing the efficiency.

Our box type ovens have the indirect heating thermo-block system with convection heat transfer. It can be manufactured according to power supply sources like electricity, gas or liquid fuel. The inner surfaces of our ovens’ panels are produced with galvanized sheet and the outer surfaces are produced with galvanized sheet steel coated with electrostatic powder paint. Considering the application temperature, the required thickness (usually 160mm) is determined and only rock wool is used for insulation. For paint applications up to 220 °C, for special purposes up to 400 °C ovens can be produced by our company. The doors of our box type furnaces can be produced as double-sided, top opening or as guillotine door according to needs.

Standard: AISI, ASTM, BS, DIN, GB, JIS, AS ETC   Thickness:  0.12-3.5mm   Width:1250/1220/1200/1000/914/762(before corrugation)930/915/910/905/900/880/875/815/810/790/780/680/670/660/655/650(after corrugation) or as required.   Ditch and Peak after corrugation: 12 Ditches/11 Peak; 11 Ditches/10 Peak; 9 Ditches/ 8 Peak   Length: In coil or as required   Zinc Coating: Z40-275g/sqm    Paint Top: 15 - 35 Microns    Paint Back: 5 - 35 Microns    Coating Color: ALL RAL Cards Color    Coating Type: Top Painted : PVDF / HDP / SMP / PE / PU                            Primer Painted : Polyurethane / Epoxy / PE                            Back Painted : Epoxy / Modified Polyester   Coil Weight: 3-8 Tons   Coil ID: 508/610mm Color: RAL Code Or According To Customer's Sample   Spangle: No spangle, With spangle   MOQ: 5 Tons   Package: Standard Sea Worthy Package   Port: China

Hai Tong focus on sheet metal parts and we are professional sheet metal bender in China, we develop various kinds of sheet metal boxes using blanking, bending, TIG welding, grinding, and powder coating, some sheet metal boxes can be waterproof with IP65.

The B 400 combines great evaporation performance with economical continuous operation in a sturdy housing. Thanks to the permanent rotation, the air is effectively washed and at the same time humidified before being evenly distributed back into the air in the room without condensation, by means of a 2-speed fan. The B 400s quiet-running synchronous motor enables even large rooms to be humidified without running up large electricity bills. B 400 Benefits in practice: Clearly designed operating panel with hygrostat and fan control and level indicators Rotating evaporation fleece cleans and washes the air 2-speed fan Automatic power-off Adjustable vent grid Robust, powder-coated sheet steel construction With built-in brace for optimal air circulation

SIGNICOLOR is a pre-coated aluminum sheet that combines aesthetics and functionality. The high-quality surface of SIGNICOLOR is ideal for screen and digital printing, laminating and lacquering for aluminum signs. Due to its smooth, high-gloss finish, no further treatment is needed after delivery. This sheet is ideal for a broad range of applications, including advertising signs, pylons, informational signs, logos and stairway advertising. Used for aluminum signs both indoor and outdoor, SIGNICOLOR undergoes strict quality controls. It’s easy to handle, cost-effective, stable and durable.

ELECTRICAL SPACE HEATER TDS 120 RProfessional heating for large building areas: With the TDS 120 R and a full 30 kW heating force Owing to 30 kW of heating power, the most powerful model of the TDS-R series comes with convenient spare capacity for the permanent heating of larger rooms and is hence especially suited for temperature control in larger building sections. Accommodated in a comfortably transportable and stable carriage construction with ball-bearing wheels, the fully galvanized, coated steel sheet housing of the electrical space heater TDS 120 R houses high-quality corrosion-protected stainless steel heating elements, which immediately after switching on generate formidable heat flowing out in large volumes via the powerful air circulating follow-up fan. The desired temperature can be regulated as needed via the integrated infinitely variable thermostat and the heating capacity can be increased in two stages up to 30 kW for maximum selected warmth.

Framework galvanized bolted steel. Wall / Facade Structure made of galvanized steel, cladding of nonflammable Plasterboard A1. Cladding of concrete fiber panels (natural, rock and wood appearance). Roof Panel and galvanized steel roofs, a wide selection of roof coating (galvanized and painted trapezoidal sheet or sandwich panel coating with polyurethane insulation, or tarred corrugated plates). Metallic or Pvc rain gutters and drainage pipes. Insulation Rock wool or glass fiber Door exterior (Steel, aluminum, Pvc, fireresistant doors, antiintruders protection); interior( Mdf, Aluminium, Pvc, fireresistant doors) Windows Doubleglass with Pvc or aluminum frame, doublepanel windows, sliding or guillotinestyle. Parasol, rolling shutter in Pvc, steel antiintrusion protection. Painting Exterior in silicone or epoxy. Interior polyurethane. Electrical system lighting structures, sockets and switches, cables, fuses and fuse boxes, relays.

YOU TAKE CARE OF THE COLOR, WE TAKE CARE OF THE QUALITY For paint tests, we are able to produce paint test panels that are made of various materials, offering a wide range of coatings, shapes and surface finish options. Of course we attach great importance to meeting your requirements. Upon request, we supply bright-finish, degreased or pre-treated panels. Moreover, test panels can be provided with drilled holes or rounded corners. You can also order test specimens made of any common materials such as wood, glass, aluminum, steel or plastic for the TABER abraser test. From various metals From various plastics With boreholes Bare or pretreated Degreased and vacuum-packed Various sizes upon request Coil-coated aluminum or sheet steel upon request

Maximize performance of powder-coating systems POREX ® fluidizing sheets help provide a uniform and evenly distributed air supply stream in powder-coating systems in which powder should flow like water. With our special molding process, fluidizing sheets are developed with consistent pore sizes and airflow characteristics. Fluidizing sheet quality and performance is carefully checked using specially designed test devices and procedures, which ensures confidence with every use. To maximize performance, our fluidizing sheets: Deliver uniform powder distribution – Powder flows like water because the sheet provides a uniform distribution of air. Allow full fluidization – Engineered porous sheets maximize the efficiency of powder-coating systems. Ensure consistent system performance – Special molding process establishes evenly distributed pore sizes and airflow properties. Features Consistent pore structure evenly distributes air stream Strong and rigid for maximum service life and...

Maximize performance of powder-coating systems POREX ® fluidizing sheets help provide a uniform and evenly distributed air supply stream in powder-coating systems in which powder should flow like water. With our special molding process, fluidizing sheets are developed with consistent pore sizes and airflow characteristics. Fluidizing sheet quality and performance is carefully checked using specially designed test devices and procedures, which ensures confidence with every use. To maximize performance, our fluidizing sheets: Deliver uniform powder distribution – Powder flows like water because the sheet provides a uniform distribution of air. Allow full fluidization – Engineered porous sheets maximize the efficiency of powder-coating systems. Ensure consistent system performance – Special molding process establishes evenly distributed pore sizes and airflow properties. Features Consistent pore structure evenly distributes air stream Strong and rigid for maximum service life and...

Maximize performance of powder-coating systems POREX ® fluidizing sheets help provide a uniform and evenly distributed air supply stream in powder-coating systems in which powder should flow like water. With our special molding process, fluidizing sheets are developed with consistent pore sizes and airflow characteristics. Fluidizing sheet quality and performance is carefully checked using specially designed test devices and procedures, which ensures confidence with every use. To maximize performance, our fluidizing sheets: Deliver uniform powder distribution – Powder flows like water because the sheet provides a uniform distribution of air. Allow full fluidization – Engineered porous sheets maximize the efficiency of powder-coating systems. Ensure consistent system performance – Special molding process establishes evenly distributed pore sizes and airflow properties. Features Consistent pore structure evenly distributes air stream Strong and rigid for maximum service life and...

Automatic control of thermal diebolts of extrusion dies The DieControl APC Pro automatically controls thermal bolts of extrusion dies according to the earlier measured cross-section profile of the material. This results in uniformly thick films, sheets or coatings even with fluctuations in the feed, material change or when starting the system. The automatic control and the extrusion close to the set point also achieve considerable material savings and quality improvement.

Good formability and conductivity make our products useful for condenser case products produced via drawing processes. Manufacturers of these aluminum case applications rely on Novelis to provide high-quality aluminum coils or sheet in alloys such as 1050 and 3004. Novelis produces pre-painted aluminum for scales, dials and nameplates in laser engraving quality, in the form of a surface-treated coil or sheet. Specialized coatings are applied by rollers. Printing is possible via standard commercial inks and paints with no special materials required.

Maximize performance of powder-coating systems POREX ® fluidizing sheets help provide a uniform and evenly distributed air supply stream in powder-coating systems in which powder should flow like water. With our special molding process, fluidizing sheets are developed with consistent pore sizes and airflow characteristics. Fluidizing sheet quality and performance is carefully checked using specially designed test devices and procedures, which ensures confidence with every use. To maximize performance, our fluidizing sheets: Deliver uniform powder distribution – Powder flows like water because the sheet provides a uniform distribution of air. Allow full fluidization – Engineered porous sheets maximize the efficiency of powder-coating systems. Ensure consistent system performance – Special molding process establishes evenly distributed pore sizes and airflow properties. Features Consistent pore structure evenly distributes air stream Strong and rigid for maximum service life and...

Galvanized structure filled with zinc coated sheet metals. Subsequent surface finish with paint RAL 7035. Delivered without stickers andock. Special safety hole for used textile insertion. Height of the insertion hole handle 1250 mm.

Bookends, closed model. Made of 1 mm thick, epoxied, powder-coated steel. • Robust bookends made from powder-coated sheet steel

3-tier metal sorting rack for clear Organisation of documents. Wall mounting possible. • Letter tray for clear organisation of documents • With 3 compartments and side labelling windows • For A4/folio format documents • Shelves made from powder-coated sheet steel • Wall mounting possible

Complete set consisting of a metal table stand and 10 SHERPA® A5 display panels. • Complete display panel set for table applications • Table stand with 10 SHERPA display panels in A5 format • Polypropylene display panels with coloured profile frame and low-reflection film suitable for scanners • Incl. tabs with blank insert sheets for labelling the display panels • Robust table stand made from powder-coated sheet steel, L-shape for extra stability • Practical pivot mechanism for simple replacement of the displays • 5-year warranty

Galvanized Coated Steel Sheets are products obtained by subjecting hot or cold rolled sheets to zinc coating process, the surface of which is brightened and strengthened against corrosion. It is offered in various grades such as DX51, DX52, DX53, DX54, DX56, S220GD, S280GD, S320GD, S350GD, HX260LAD, HX300LAD, HX340LAD. Application Areas and Advantages: Wide usage in sectors such as automotive, white goods, machinery manufacturing, construction sector, industrial warehouse solutions, cooling heating systems, transportation systems. Zinc coating increases corrosion resistance and makes the product more durable. The amount of coating varies according to demand and place of use. Galvanized Coated Steel Sheet, which is coated with zinc by dipping or electrolytic coating method to increase the corrosion resistance of the steel sheet, is usually coated with a total of 100-300 gr / square meter on both surfaces.

Metal wall mount for 5 A4 display panels. • Robust and durable wall mount made of powder-coated steel sheet • Capacity: For 5 display panels in A4 format (not included in the delivery) • Practical pivot mechanism for simple replacement of the displays • Easy assembly • Mounting of multiple wall brackets possible in rows • Ideal for permanent use in industry and trades companies

Cabinet Materials Saddled Dkp 0,70 mm. Electrostatic powder coating is applied on the sheet. Leg Materials Saddled Dkp 1,50 mm. Electrostatic powder coating is applied on the sheet. Surface Care You can clean your cabinets by wiping them with a damp cloth. Avoid prolonged contact with water. Ventilation grids. Name plate. Hanger hooks. Clover lock system suitable for padlock installation. Color: RAL 7035 GREY. Can be produced in custom color. Contact your customer representative.

Complete set consisting of a metal table stand and 20 FUNCTION A4 display panels. • Complete display panel set for table applications • Table stand with 20 FUNCTION display panels in A4 format (5 units each in red, yellow, green and blue) • Robust and durable table stand in L-shape made of powder-coated steel sheet • Display panel made from crystal-clear hard film with reinforced tab in 5/5 division and blank insert sheet • Practical pivot mechanism for simple replacement of the displays • Ideal for permanent use in industry and trades companies

Metal wall mount for 10 A4 display panels. • Robust and durable wall mount made of powder-coated steel sheet • Capacity: For 10 display panels in A4 format (not included in the delivery) • Practical pivot mechanism for simple replacement of the displays • Easy assembly • Mounting of multiple wall brackets possible in rows • Ideal for permanent use in industry and trades companies

Complete set consisting of a metal wall mount and 10 FUNCTION SAFE A4 display panels. Zippable panels for better document protection. • Complete display panel set for wall applications • Wall-mounted display panel system with 10 FUNCTION SAFE display panels in A4 format • Zip closure on the side of the display panels protects documents against moisture and dirt • Robust and durable wall mount made of powder-coated steel sheet • Display panel made from crystal-clear hard film with reinforced tab in 5/5 division and blank insert sheet • Practical pivot mechanism for simple replacement of the displays • Ideal for use in kitchens, production plants or shops such as butcheries and bakeries • Easy assembly

Zinc-coated galvanized sheets are transformed into painted sheets with various color options through a special surface painting process. Products offered in colors such as RAL9002, RAL3009, RAL7016 are coated with protective film and topcoat paint to achieve a perfect appearance. Technology and Durability Together: The steel sheet surface is reinforced with primer paint and PET film coating processes. The thick PVC-based topcoat offers high flexibility, scratch resistance and styling properties. Plastisol can be safely used indoors and outdoors in roofing, cladding and gutter systems. Areas of Use: Pre-painted sheets are preferred in many sectors from furniture to construction. It combines aesthetics and durability by being used in roll, sheet, trapezoidal, corrugated and embossed shapes. Aesthetics and Protection: Various colors of PPGI add an aesthetic touch to your projects. It also offers a long-lasting and durable material thanks to its zinc coating and protective film.

Cabinet Materials Saddled Dkp 0,70 mm. Electrostatic powder coating is applied on the sheet. Leg Materials Saddled Dkp 1,50 mm. Electrostatic powder coating is applied on the sheet. Surface Care You can clean your cabinets by wiping them with a damp cloth. Avoid prolonged contact with water. 2 shelves. Ventilation grids. Name plate. Hanger hooks. Clover lock system suitable for padlock installation. Color: RAL 7035 GREY. Can be produced in custom color. Contact your customer representative.

Cabinet Materials Saddled Dkp 0,70 mm. Electrostatic powder coating is applied on the sheet. Leg Materials Saddled Dkp 1,50 mm. Electrostatic powder coating is applied on the sheet. Surface Care You can clean your cabinets by wiping them with a damp cloth. Avoid prolonged contact with water. 2 shelves. Ventilation grids. Name plate. Hanger hooks. Clover lock system suitable for padlock installation. Color: RAL 7035 GREY. Can be produced in custom color. Contact your customer representative