Media - Import export

The Pump Set is suitable for thin, flammable and highly inflammable liquids. Perfectly suited for withdrawing or transferring explosive media. * Optionally available with Ex - plug * Pump tube equipped with Lutz original handwheel * Suitable for filling or transferring alternative fuels, oils, flammable liquids Features & Advantages * Optionally with electric or compressed air drive * No lubricants and therefore no contamination of the pumped medium by lubricants * Highly resistant noble carbon shaft bearing * Maintenance without special tools * Seal modules of the seal-less (DL) pump are interchangeable * Approved according to ATEX directive 2014/34/EU, category 1/2 * The maximum flow rate is a value determined by means of a test bench and measured with water at a liquid temperature of approx. 20 °C . The measurement is taken at the pressure joint of the pump, without hose, nozzle or flow meter.‌

In addition to the MADI interfaces available on the processor card, the MN-RN300 RockNet Audio Interface Card gives access to the wide range of Riedel RockNet audio interface modules.

MediorNet Mainframes can be easily configured with the input and output cards needed for a specific installation. All Media Cards support multiple video standards and on-board signal processing and conversion, reducing the number of individual cards to a minimum. These signal standards and processing features can be updated via software, securing the hardware investment for future development.

MediorNet offers Link Cards with and without integrated CWDM multiplexing to network MediorNet mainframes with a bandwidth of up to 76.5 Gbit/s on a single fiber link. MediorNet‘s standard fiber transceivers have an optical budget of 18 dB minimum, allowing for distances of up to 40 km (25 miles). A MediorNet fiber link always consists of duplex fiber to allow bi-directional signal transport. MediorNet CWDM Link Cards can also include external optical signals and transport them transparently through the system. All MediorNet Link Cards provide signal monitoring and link status information, which can be monitored via status LEDs and system wide via the MediorWorks software and SNMP network management systems.

MediorNet Modular allows the customers to configure the mainframe to their requirements. The frame can be filled with various Media and Link cards, as needed for the specific application. All modules and cards are hot swappable. Redundant power supplies guarantee maximum reliability. The optimized cooling concept of MediorNet results in a very low-noise system. The horizontal air ow within the device allows for effective cooling without the need for additional rack space below or above the MediorNet mainframe. MediorNet frames can be rack mounted in various positions, e.g. with all connectors on the front or on the rear side, or recessed to allow cabling from the front but without connectors or cables exceeding the rack’s dimensions. The IEC connectors can be located front or rear independent from the other cabling.

MediorNet Compact is the cost-effective and easy-to-use entry to the Riedel MediorNet world of integrated media signal distribution and processing. It is the first fiber-based 21st-century stage box providing the flexibility of a true real-time media network including integrated signal processing at the cost of simple multiplexing point-to-point products. With a network bandwidth of 50 Gbit/s MediorNet Compact provides enough capacity for bi-directional transport of 12 HD-SDI signal, dozens of MADI streams or Gbit-Ethernet signals and hundreds of audio channels or intercom ports – ideal for streamlining the infrastructure of any mobile, studio or live event application.

MediorNet Compact is the cost-effective and easy-to-use entry to the Riedel MediorNet world of integrated media signal distribution and processing. It is the first fiber-based 21st-century stage box providing the flexibility of a true real-time media network including integrated signal processing at the cost of simple multiplexing point-to-point products. With a network bandwidth of 50 Gbit/s MediorNet Compact provides enough capacity for bi-directional transport of 12 HD-SDI signal, dozens of MADI streams or GBit-Ethernet signals and hundreds of audio channels or intercom ports – ideal for streamlining the infrastructure of any mobile, studio or live event application.

In addition to the MADI interfaces available on the processor card, the MN-RN300 RockNet Audio Interface Card gives access to the wide range of Riedel RockNet audio interface modules.

In addition to its fiber-based real-time network solution MediorNet, Riedel offers a range of accessories solving everyday issues in fiber installations. The Riedel Smart Rack solution offers a flexible, versatile and easy-to-use solution. The Smart Rack Suite consists of WDM and CWDM Multiplexers and De-Multiplexers as well as RF over fiber converters and patch modules.

The intuitive configuration, control, and monitoring software MediorWorks can be downloaded from any MediorNet mainframe via the Configuration Port of the Processing Card. This way you always have access to the correct software version of a specific installation. The software is a JavaTM based application, allowing any computer with a JavaTM Runtime environment such as Windows, Mac OS X or Linux to serve as the host for the application. MediorWorks auto senses the configuration and status of the system it is connected to. Five windows give easy access to any aspect of the MediorNet installation. All windows are visible at the same time. Alternatively, they can easily be accessed via one mouse click on the “Views”-window, which is floating above all other windows. The “Device Browser” shows all available nodes, the cards installed in the node and each connector of the specific media card. If a connector is selected, the “Connections”-window shows the active connections and how the...

MediorNet Modular allows the customers to configure the mainframe to their requirements. The frame can be filled with various Media and Link cards, as needed for the specific application. All modules and cards are hot swappable. Redundant power supplies guarantee maximum reliability. The optimized cooling concept of MediorNet results in a very low-noise system. The horizontal airflow within the device allows for effective cooling without the need for additional rack space below or above the MediorNet mainframe. MediorNet frames can be rack mounted in various positions, e.g. with all connectors on the front or on the rear side, or recessed to allow cabling from the front but without connectors or cables exceeding the rack’s dimensions. The IEC connectors can be located front or rear independent from the other cabling.

MediorNet Compact is the cost-effective and easy-to-use entry to the Riedel MediorNet world of integrated media signal distribution and processing. It is the first fiber-based 21st-century stage box providing the flexibility of a true real-time media network including integrated signal processing at the cost of simple multiplexing point-to-point products. With a network bandwidth of 50 Gbit/s MediorNet Compact provides enough capacity for bi-directional transport of 12 HD-SDI signal, dozens of MADI streams or GBit-Ethernet signals and hundreds of audio channels or intercom ports – ideal for streamlining the infrastructure of any mobile, studio or live event application.

MicroN is an 80G media distribution network device for Riedel’s MediorNet line of media transport and management solutions. Working seamlessly with the MediorNet MetroN core fiber router, MicroN is a high-density signal interface with a complete array of audio, video, and data inputs and outputs, including 12 SD/HD/3G-SDI inputs and 12 SD/HD/3G-SDI outputs, two MADI optical digital audio ports, a Gigabit Ethernet port, two sync reference I/Os, and eight 10G MediorNet Links (4.25 capable). MicroN is available as a fully networked MediorNet device, as well as in a point-to-point edition at a very competitive price point. In just 1RU, MicroN offers a highly versatile signal interface that can be used in productions of every size and complexity. For the largest media networks built on MediorNet transport devices, MicroN can serve as a breakout box for a MetroN router and extend connectivity beyond the fiber I/Os to any type of video and audio I/O required. Or, MicroN can simply work...

Filters made at our factory in Nantes (France) This filter uses the same principle than Standard Pleated Cardboard Filter with a polyester media sticked at the back in order to increase filtration efficiency for dry dusts. Advantages of this filter : - Lifetime up to 3-4 times longer than other filtering medias on the market - Better filtration efficiency than Standard Pleated Cardboard Filter - Easy installation and manipulation This filter can be used in all spray booths with horizontal and vertical airflow. Construction : This filter is made of 2 layers of recycled kraft paper, perforated, pleated and glued with a polyester media at the back. The quality of kraft paper (250g/m²) guaranties rigidity of the filter in all positions. Standard widths : - 1m - 0,90m - 0,75m Other dimensions and cuts on demand.

Heat recovery with the help of heat exchangers In industry, waste heat occurs at many points in the production process, which is often released into the environment without being used. In many cases, energy is even used to cool the waste heat flows from production so that they can be released into the environment. Heat exchangers (also called heat exchangers) are used for heat recovery so that the waste heat generated in the production process can be used again in the company. Gaseous or liquid media Waste heat can be in the form of gaseous media (e.g. warm exhaust air, steam, exhaust gases, etc.) or in the form of liquid media (e.g. hot water or other liquids). With the help of heat exchangers, the waste heat can be recovered from both gaseous and liquid media and then made available to the production process at a suitable point as energy in gaseous or liquid media. This process is known as energy recovery or also as heat recovery.

Crystal-clear pool water with the highest hygienic factor through glass filter medium, resistant against biofilm and bacteria, 99.99% free from contamination, less backwashing due to anti-compaction technology, economical use of pool chemistry, JUST ONE granular size for all filter sizes necessary, FILTRATION up to 10 μ, easy handling 20 kg bags

Eccentric screw pump tube B70V-SR Industrywith reduction gear for electric motors For pumping highly flammable liquids and for use in "Zone 0", use Pump tubes with mechanical seal (GLRD), cardan shaft (GW) and PTFE stator. The Eccentric screw pump B70V-SR 12.1 (with reduction gear) in the industrial version is suitable for pumping water-like to highly viscous media with and without fibrous or solid materials. Depending on the application, various compressed air and electric motors are available, which you can combine with the Pump tube at any time. This gives you flexibility at all times and saves important resources. * PTO shaft versions also available in special immersion depths of 500 - 2000 mm * Media examples: viscous mineral oils, resins, emulsions, paints and many other thick materials * Uniform volume flow * Easy and fast cleaning * Gentle, low-pulsation product delivery * Low wear * Ideal for mobile use

The double diaphragm pump is suitable for the food and pharmaceutical industry as well as for emptying drums, IBCs and tanks. * typical applications: liquid foodstuffs and semi-luxury food, pharmaceutical substances and cosmetic products * integrated muffler up to model size AODD 1 * FDA-compliant Features & Benefits * high hydraulic performance * maintenance-optimised design and simple installation * self-priming (even when dry) * ice-free air system * non-stalling operation * food-safe connections

The eccentric worm-drive pump B70V-SR (with reduction gear) in PURE design is suitable for pumping water-like to highly viscous media with and without fibres or solids. Depending on the application, various electric and compressed air motors are available, which you can combine with the pumping unit at any time. This gives you flexibility at all times and saves important resources. * Also available in special immersion depths * Examples of media: viscous cosmetic products, foodstuffs, etc. * Uniform volume flow * Gentle, low-pulsation product conveyance * Low wear and tear * Ideal for mobile use * Approved in accordance with ATEX Directive 2014/34/EU, category 1/2

This high performance computer-controlled machine provides maximum economic efficiency at treatment of big batch volumes at high throughput! The comfortable operator features on newest level leave no wish unfulfilled: touchscreen operation, USB/SSD hard disk, network connection (support via internet), recipes memory, user management, logging/documentation/traceability and optional barcode scanner/ID key. At any time, this machine is ready for upgrade to automated application, from the automatic loading & deloading of the machine up to a complete full automated feeding & forwarding system. For industry 4.0 demands, the E90 is best prepared. Standardwise, a monitoring of the processing data via network is possible also from an external working place. On option, the control via OPC-UA server is possible, too. Furthermore, this machine is able to perform cryogenic deburring without need of blasting media (drum-only deflashing), suitable for special applications only.

The first flowmeter with touch screen display and backlighting convinces with its simple, demand-oriented display and operability, the multilingual interface and the compact design: The rotating swash plate and a magnet enable the exact measurement of the volume flow and measure thin to medium viscous media such as water and mineral oils precisely, quickly and above all efficiently. As an option, the desired quantity can be preselected with a quantity preselection (relay module), so that the pump or the system switches off automatically after the selected quantity.thus, the operation of the systems is simplified and secured even more. * Optional with volume preselection (relay module) * Media examples: Water, oil, diesel, heating oil, hydraulic oils etc. * Mobile on a Drum pump or with a nozzle connection or stationary in plant construction

Plastic is a thermoplastic and belongs to the organic polyamidebased blasting abrasives. WIWOX® KS nature high-quality blasting and deburring medium is particularly suitable to treat duroplast and rubber components without damaging and matting them. Available in cylindrical or exact cubic shape, it is characterised by high impact strength, dimensional stability and extremely long service life. We also supply an antistatic agent for subsequent or sustained application in liquid form.

Plastic blasting abrasives type WIWOX® KS have been specially developed for optimum, chemically neutral surface treatment and all gentle cleaning – especially for plastic and light metal. They are mainly used for paint stripping, roughening, matting, deburring and cleaning. Plastic blasting abrasives produce consistently high quality and do not cause any damage to the work piece to be treated.

WIWOX® SD rounded cut wire shot is mainly used for cleanblasting and shot peening. Depending on the quality of the raw material used, different hardness classes are obtained. We supply non-corrosive cut wire shot that meet the requirement of particularly high demands. Cylindrical cut wire shot blasting abrasives are cut from wire. The length of the grain is equal to the diameter. Grain shapes of different roundness are produced through the subsequent rounding of the cylindrical raw material, rounded from G1 – G3. Cut wire shot has a particularly long service life and are known for low dust generation.

Chilled iron grit blasting abrasives type WIWOX® HG are produced by melting cast iron. It receives its angular shape through the subsequent atomisation and breaking. The advantage of this blasting abrasive lies in the consistently high abrasiveness, as it remains sharp-edged in the mixture and the edges do not become round. It breaks up into smaller sharp-edged and aggressive particles during the blasting process.

Due to the different thermal tempering, steel shot blasting abrasives type WIWOX® SK obtain different hardness classes from 40 – 43 HRC, 54 – 60 HRC up to greater than 61 HRC. Because of the different degrees of hardness, the steel shot in the operating mixture keeps its angular shape or becomes round during the application process.

Due to its extreme hardness, WIWOX® SG high-carbon cast steel abrasive reaches an extremely high blasting intensity right from the start. It is produced in a melting process and gets its round shape through the subsequent atomising process. The metallic structure of this low-carbon cast steel abrasive is decisive for its long service life.

WIWOX® EDK Stainless steel blasting abrasives are produced in a melting process and crushed into angular granules. It is distinguished by its long service life as well as its aggressiveness and presents an economic alternative to other angular blasting abrasives.

WIWOX® ED Stainless steel blasting abrasives are produced in a melting process and get its round shape through the subsequent atomising process. These fine particles have a particularly long service life and are known for low dust generation. We also supply stainless steel blasting abrasives manufactured under vacuum that meet the requirement of particularly high demands. This blasting abrasive is distinguished by its lustre, purity and roundness.