Wire - Import export

In Dutex s.r.l. Patelec produces customized wire harnesses, cords and cable assemblies with simple finishing as faston and housing, shrink tubing, clamps, inductors, resistors, or even complex assemblies.

This inline thermocouple is especially invented for using under humid conditions. Compared with normal wire production this wire isolation is made in one work process, both conductors get moulded in Teflon at the same time. With this wire the measurement equipment is protected from capillary rising moisture through the wire. gas-, steam- and watertight Temperature range: -75°C to +250 °C, short-duration to + 300 °C Wire type: Teflon,0.38 mm, solid, Tmax: +300 °C

This inline thermocouple can be individually installed. For measurements in the wiring harness, on difficult to access points or on the smallest components. The thin wire facilitates very flexible installation. The fibreglass insulation facilitates routing the probe along very hot components (Tmax. 450 °C). The thin probe tip guarantees very rapid response. Temperature range: -100 °C to +450 °C Wire type: Fibreglass/fibreglass, 0.2 mm, wire, Tmax: +450 °C

This inline thermocouple can be individually installed. For measurements in the wiring harness, on difficult to access points or on the smallest components. The wire facilitates very flexible installation. The fibreglass insulation facilitates routing the probe along very hot components (Tmax. 450 °C). The thin probe tip guarantees very rapid response. Temperature range: -100 °C to +450 °C Wire type: Fibreglass/fibreglass, 0.5 mm, wire, Tmax: +450 °C

This inline thermocouple can be individually installed. For measurements in the wiring harness, on difficult to access points or on the smallest components. The thin wire, barely 0.7 mm in diameter, facilitates highly flexible installation. The thin probe tip guarantees very rapid response. Temperature range: :-190 °C to +260 °C, short-duration to +300 °C Wire type: Teflon,0.08 mm, wire, Tmax: +300 °C

This inline thermocouple can be individually installed. For measurements in the wiring harness, on difficult to access points or on the smallest components. The thin wire, barely 2 mm in diameter, facilitates highly flexible installation. The thin probe tip guarantees very rapid response. Temperature range: -100 °C to + +200 °C, short-duration to + 230 °C Wire type: Teflon, 0.2 mm, wire, Tmax: +200 °C

Sheathing thermocouples can be used anywhere due to their ruggedness and small design. Whether in industry, development or in the lab. The measurement point is hot junction insulated as standard to exclude any falsification of the measurement evaluation through superposition of the offsets. Sheathing thermocouples are freely flexible across their entire length. That means the thermocouple can be integrated in the installation point. The temperature to be measured can therefore be registered near the desired measuring point. A possible connection lead permits simple routing up to the measured-data acquisition. Options are available for the element diameter, element and wire length as well as the type of connection configuration (plug, socket, bare wire ends, etc.).

Sheathing thermocouples can be used anywhere due to their ruggedness and small design. Whether in industry, development or in the lab. The measurement point is hot junction insulated as standard to exclude any falsification of the measurement evaluation through superposition of the offsets. Sheathing thermocouples are freely flexible across their entire length. That means the thermocouple can be integrated in the installation point. The temperature to be measured can therefore be registered near the desired measuring point. A possible connection lead permits simple routing up to the measured-data acquisition. Options are available for the element diameter, element and wire length as well as the type of connection configuration (plug, socket, bare wire ends, etc.). Temperature range: -100 °C to +750 °C, continuous, depending on selected sheathing diameter and measuring medium or atmosphere

Application: A set wire inserts fitted in the entrance hole of the connector will provide a very good strain relief without any protruding parts from the connector. Construction: • Thermoplastic material with a round or oval hole fit around a specific wire.

Use: Designed for soldering or crimping on mineral insulated sheath cable or crimping on insulated wire. Construction: Brass machined, nickel plated insert with 0.1 mm tolerance on the cable OD.

Use: Connectors for thermocouples and resistance thermometers measurement circuits. Suitable for measurement with small wires and mineral-insulated metal sheathed cables. Mechanical design: • Housing of high quality fibreglass-filled thermoplastic plastic • Contacts of original thermocouple material pins and spring-loaded inserts for reliable contact • Easy wire connection through sandwich construction • Reverse polarity protection by different contact pin widths • One-piece housing withstands great stresses • Moulded barriers prevent short circuit • Stainless steel screws with combination head (Slotted and Phillips) terminals enable quick connection

Sheathing resistance thermometer Ni120 without wire with flexible sheathing design

Sheathing resistance thermometer Pt1000 without wire with flexible sheathing design

Sheathing resistance thermometer Pt100 without wire with flexible sheathing design

Standard resistance thermometer Pt100

Inline resistance thermometer Ni120

This thermocouple extension can be used with any Type K thermocouple. The selection of high-quality components ensures a long service life.