Putty knife - Import export

TECHNICAL DEFINITION Extra-fine finishing filler in powder form for all types of interior jobs. The substrate is now ready to be decorated with paint, wallpaper or any wall covering. COMPOSITION AND APPEARANCE Calcium carbonate, redispersible resin, rheological agent and various additives. Produces a white paste. SUITABLE SURFACES • Wallpaper • paint • wall covering • Plasterboards • Concrete • Old paint • Plaster-based high build filler • Plaster blocks • Cement render • Undercoat TECHNICAL CHARACTERISTICS • Setting time : >24hrs (drying filler) • Powder’s density : 0.8 • Grain size : very fine • pH : 7 • Adhesion : complies with standard NFT 30 608 MIXING FACTOR Use approximately 11-12 litres of water for one 25 kg bag. Allow the paste to rest for 15 min before use. APPLICATION Apply either manually with a steel trowel or a putty knife, or mechanically. Allow to harden and scrape off any possible imperfection before sanding down.

COMPOSITION AND APPEARANCE Plaster-based powder coating containing calcium carbonate, resin, cellulose fibre and various additives. The mixed paste is white in colour. REFERENCE DOCUMENTS • DTU 25.41. Standard DIN 1168 • DTU 59.1: painting work • NF EN 13963 TECHNICAL CHARACTERISTICS • Granulometry: fine • Adhesion: complies with NFT 30 608 • pH: neutral APPLICATION • SEALING PLASTERBOARDS WITH ROUNDED EDGES Apply a first pass by filling the joint deeply, apply a second pass after 1 1/2 hours to smooth and finish the joint. Filling and bonding (if tape) in one pass. And finishing is possible in a single layer. • FILLING, ASSEMBLY, SEALING Dilute with 45% water. 2.2 l to 2.3 l water per 5 kg bag or 11 l to 11.5 l for 25 kg. Open bevelled cracks or rifts. Apply with a putty knife or spatula. Completely fill up the part to be filled, smooth carefully. Time of use: 45 min. Hardening: approx. 1 hour.

COMPOSITION AND APPEARANCE Powder filler based on plaster, calcium carbonate and various additives. The resulting paste is white. SUPPORT AGREED All types of interior substrates. COATINGS DTU 59.1. MATERIALS AVAILABLE DTU 59.1 TECHNICAL CHARACTERISTICS • Setting time : 2 hours • Particle size : fine SUITABLE SURFACES The substrates must be in conformity with DTU 59.1, i.e., clean, hard, free of dust and any trace of release agent. Scrape down, sand and wash old paint. USE CAUTION The temperature during application and drying must be between 5 and 30°C. Do not apply to a damp substrate. Do not use mix that has begun to harden. RATE TEMPERING Around 10 to 12 l of water per 25 kg sack. Mixing is preferably to be carried out mechanically. APPLICATION Application is to be carried out using a float, a knife or a putty knife for smoothing. For a decorative finish, use a roller, brush or sponge.

fako® Sealing putty 3765, made of butylrubber, has been developed as a supplement to the fako® Sealing strip 3714, for most sealing purposes where absolute resistance to ageing is required and for which an intermediate layer of 0.8 mm to 1 mm has to be used. In combination with the Sealing strip 3714 most desired thickness’s can be obtained for seals. The putty does not become hard but remains plastic and elastic. To fulfil its requirements the putty has not only to be elastic but also plastic so that, when pressed, it will penetrate into any gaps and remain, thus forming a complete seal. Technically this is only possible through a combination of two basic materials with the same chemical composition but with different molecular weights. With two components the above requirement is met for both sufficient penetration depth and stability of the kit at the same time. By simple filling with a putty knife, you can obtain a min. thickness of approx. 0.2 to 0.3 mm. Priming is not required.