Fillers - Import export

TECHNICAL DEFINITION Cement-based powder filler with fibres for treating damaged exterior substrates. The filler is multi-purpose: can be used to fill, repair and rectify wall surfaces, with a smooth finish. SUITABLE SUBSTRATES All types of substrates : cement, concrete, concrete blocks, stones, brick, old paintwork, old tiling. COVERINGS Once the filler is completely dry, can be covered with all types of coatings and paintwork. Do not directly cover with solvent-borne paint. TECHNICAL FEATURES • Setting time: 30 to 40 minutes • Adhesion: complies with EN 16566 • AFNOR NFT 36.005 classification: Family IV class 4c MIXING PROPORTIONS • 6 to 6.5 litres of water per 15 kg bag • 2 to 2.2 litres of water per 5 kg bag • 0.4 - 0.43l of water for 1 kg • 2 volumes of water for 5 volumes of powder APPLICATION Application with a plastering spatula, knife, smoothing trowel. Clean tools with water. COVERAGE Approximately 1 kg per m²/mm of thickness.

TECHNICAL PROPERTIES Primer filler for vertical surfaces or for use on ceilings made from poured concrete or pre-slabs. Decorating filler, for smoothing over. Smooth, matt finish. Odour-free. COMPOSITION AND APPEARANCE. Solvents : Water. Filler : Calcium carbonates. Additives : Dispersing agent, bactericidal fungicide. Thickeners : Cellulosic, polyacrylates. Binders : Acrylic dispersing agent. Density : 1.86. Dry matter : 75%. TECHNICAL PROPERTIES • Fire classification: A2-S1, d0 SUITABLE SURFACES Interior : ideal for covering bricks, brick tiles, cement breeze blocks, cinder blocks, de-bubbling pre-slabs, shuttered concrete, aerated concrete, for redecorating stippled walls or old damaged surfaces. APPLICATION. • The first coat should be levelled out using 60 cm scraper or skimmed with a rule. • After drying, the second coat should be smoothed with a scraper. • After allowing to set slightly, squeeze the filler at a slight angle using a clean scraper.

TECHNICAL DEFINITION Ready-to-use surface filler paste for filling interior holes and cracks. COMPOSITION AND APPEARANCE Water, calcium carbonate, sand, resin and various additives. SUITABLE SUBSTRATES All types of interior substrates : concrete, cellular concrete, cement, breeze block, brick, plasterboard, plaster tiles, plaster, old paint. COVERING Primer coat, smooth surface filler, wall coverings, paint REFERENCE DOCUMENTS • Filler meets EN 16566 standard • DTU 59.1 : Paint work TECHNICAL CHARACTERISTICS • Density : 1.5 • Dry extract : 82 % STORAGE 9 months in original unopened packaging away from frost and high temperatures. PREPARATION OF SUBSTRATES Substrates must comply with the DTU 59.1 standard i.e. be dry, clean, dust-free, hard and free of any trace of separating agent. APPLICATION Applied by hand using a filling knife or spatula. The thickness is 2 cm; to fill deeper holes, build up the filler in several steps The maximum thickness will be 1 cm per coat.

TECHNICAL DEFINITION Multi-purpose filler for interior use. • Filling holes, cracks, chases • Fixing and bedding • Pasting polystyrene, roses, cornices • Finishing COMPOSITION AND APPEARANCE Powder filler composed of plaster, calcium carbonate, resin, cellulose fibre and various additives. Produces a white paste. ACCEPTED SUBSTRATES All types of interior substrates: plaster, plasterboards, plaster blocks, concrete, cement rendering,concrete blocks, aerated concrete, brick, earthenware, TECHNICAL CHARACTERISTICS • Grain size : fine • Adhesion : complies with standard NFT 30 608 • pH : neutral • Setting starts after 50 minutes • Setting ends in 1 hr 10 min • Bending : 3 N/mm2 • Compression : 7 N/mm 12 kg buckets on wrapped pallet. STORAGE 9 months in original unopened packing protected from damp. THE TEMPERATURE DURING APPLICATION AND DRYING MUST BE SUPERIOR TO 5°C. DO NOT USE ON A DAMP SUBSTRATE. DO NOT USE ONCE THE PASTE HAS STARTED TO SET.

TECHNICAL DEFINITION Extra-fine finishing filler in powder form for all types of interior jobs. The substrate is now ready to be decorated with paint, wallpaper or any wall covering. COMPOSITION AND APPEARANCE Calcium carbonate, redispersible resin, rheological agent and various additives. Produces a white paste. SUITABLE SURFACES • Wallpaper • paint • wall covering • Plasterboards • Concrete • Old paint • Plaster-based high build filler • Plaster blocks • Cement render • Undercoat TECHNICAL CHARACTERISTICS • Setting time : >24hrs (drying filler) • Powder’s density : 0.8 • Grain size : very fine • pH : 7 • Adhesion : complies with standard NFT 30 608 MIXING FACTOR Use approximately 11-12 litres of water for one 25 kg bag. Allow the paste to rest for 15 min before use. APPLICATION Apply either manually with a steel trowel or a putty knife, or mechanically. Allow to harden and scrape off any possible imperfection before sanding down.

DESCRIPTION Coating to quickly fill all sizes of cracks, holes and grooves with no shrinkage and no cracking. COMPOSITION AND APPEARANCE Plaster-based powder filler, calcium carbonate, mineral reducer, cellulose derivatives and various admixtures. The compound obtained is white in colour. SUITABLE SURFACES All types of internal unfinished or painted surfaces : plaster, plasterboard, plaster blocks, concrete, cement coating, breeze blocks, cellular concrete, bricks, terracotta... TECHNICAL CHARACTERISTICS • pH: neutral • Setting time : 30 minutes depending on the ambient conditions and the thickness applied PACKAGING 5 kg and 15 kg bags. APPLICATION To be applied using a coating knife. Amount required : 1 kg m²/mm thickness. DRYING TIME Depends on the ambient conditions, the nature of the surface and the thickness of application. Generally speaking, when spread to a thickness of one cm, the filler dries in 6 hours.

TECHNICAL DETAILS Powder filler for all types of interior filling work on uneven substrates. SEMIN HIGH BUILD FILLER has very good filling properties. SUITABLE SURFACES All types of interior surfaces: bubbled concrete, untreated concrete, cellular concrete, irregular plaster, heating ceiling, terracotta tiles, uneven substrates... Covering After the filler has dried completely, suitable for covering with all types of plaster-based coatings, thick coatings, wall paper paste, wall coverings. REFERENCE DOCUMENTS • Filler complies with standard NFT 30 608 • DTU 59.1 : painting work • Technical notice CSTB N°9/99-681 TECHNICAL CHARACTERISTICS • Granulometry : up to 0.5 mm • Adhesion : complies with NFT 30 608 • pH : neutral • Usage time for batch : 24 hours PACK SIZE 25 kg bags on shrink-wrapped pallet. APPLICATION May be applied manually with a smoothing trowel or coating blade, or mechanically by spraying then manual smoothing. THICKNESS OF APPLICATION Up to 5 mm in one pass.

TECHNICAL DEFINITION Multi-propose filler for interior use. • Flling holes, cracks, chases • Fixing and bedding • Pasting polystyrene, roses, cornices • Finishing COMPOSITION AND APPEARANCE Powder filler composed of plaster, calcium carbonate, resin, cellulose fibre and various additives. Produces a white paste. ACCEPTED SUBSTRATES All types of interior substrates : plasterboards, plaster blocks, concrete blocks, aerated concrete, brick, earthenware, etc. VIDEO 1,5 - 5 - 15 -25 kg bags on wrapped pallet. 12 kg buckets on wrapped pallet. SUITABLE SURFACES Once completely dry, SEMIN FILLER AND SMOOTH FINISH can be covered with any type of paint, plaster-based filler, paste-like filler and wallpaper paste. For tiling, choose an adhesive suited to plaster substrates. DRYING TIME This depends on the weather conditions, on the type of substrate and on the applied thickness. As a general rule, for 1 cm thickness, SEMIN FILLER AND SMOOTH FINISH dries in 6 hours.

TECHNICAL DETAILS Powder filler for all types of interior filling work on uneven substrates (rough precast concrete, for instance). COMPOSITION AND APPEARANCE Plaster-based powder coating containing calcium carbonate, resin and various additives. The mixed paste is white in colour. SUITABLE SURFACES Interior walls and ceilings: Bubble concrete, bare concrete, cellular concrete, irregular plaster, heating ceiling, uneven surfaces, etc. OVERLAYING After the filler has dried completely, suitable for covering with all types of plaster-based coatings, thick coatings, wall paper or wall coverings. TECHNICAL CHARACTERISTICS • Granulometry : Up to 0.2 mm • Adhesion : complies with NFT 30 608 • pH : neutral PACK SIZE 5 and 25 kg bags on shrink-wrapped pallet. STORAGE 9 months in unopened original packaging stored away from moisture. PREPARATION OF SURFACES Surfaces must comply with DTU 59.1, i.e. be clean, dry, dust-free and free from all traces of form oil.

TECHNICAL DEFINITION FIBRELASTIC is a ready-to-use filler paste with a high proportion of resin and glass fibre. Particularly suitable for all types of interior and exterior filling jobs. It has permanent flexibility allowing it to tolerate flexing of the substrate without cracking and it eliminates the need for repair tape. COMPOSITION AND APPEARANCE Emulsion resin, calcium carbonate, fibreglass and various additives. The paste is off-white. ACCEPTED SUBSTRATES • Plaster • Masonry • Cellular concrete • Wood • Cement render • Plasterboard • Roughcast • Old painted surfaces • Concrete • Silico-limestone brick SUITABLE SURFACES Once it has dried entirely FIBRELASTIC can be covered with any type of paint or plaster base or ready-to-use fillers. TECHNICAL CHARACTERISTICS • Viscosity (BV 1000 / 30 rpm) : 300000 mPas • Density : 1.3 • pH : 6 • Permanent elasticity PACK SIZE Tubes containing 300 g. Tubs containing 1.5 and 5 kg.

TECHNICAL DEFINITION • White fine grain repair filler for interior and exterior use • Does not shrink • High resin content • FINEX SYSTEM is a multi-purpose filler, which allows to fill holes and cracks, and to repair windowsills and damaged angles ACCEPTED SUBSTRATES Cement, concrete, bricks, concrete blocks, stone, aerated concrete, plaster, old paint, old tiling. SUITABLE SURFACES Once completely dry, FINEX SYSTEM can be covered with all types of paint, watertightness system, plaster- or cement-based fillers, and silicate, epoxy or polyurethane paint. TECHNICAL CHARACTERISTICS • Grain size : fine • Adhesion : complies with standard DTU 42.1 • pH : 9 once dry • Setting starts after 50 minutes • Setting ends in 1 hr 10 min PREPARATION OF SURFACES BEFORE APPLICATION The substrate must be clean, dry, free of dust and of any trace of stripping oil. Walls that are peeling off must be scraped beforehand. Strip any old paint in poor condition and remove any old thick plastic covering.

TECHNICAL DEFINITION Ultra-light ready mixed filler for repair of interior or exterior walls and ceilings. Shrink free and fast drying, SEM-LIGHT is ideal for high quality filling jobs and is very ease to use. COMPOSITION AND APPEARANCE Resins in emulsion with lightening agents and various additives. The paste is snow white. ACCEPTED SUBSTRATES Interior and exterior walls and ceilings • Plaster • Masonry • Cellular concrete • Concrete • Plasterboard • Roughcast • Wood • Cement render TECHNICAL CHARACTERISTICS • Density : 0.4 • pH : 7 • Shrink-free filling • Excellent application qualities STORAGE 12 months in unopened original packing protected from frost and extreme heat. PREPARATION OF SURFACES BEFORE APPLICATION The substrates must be clean, free of dust and any trace of formwork release oil. Indoors, during hot weather or on absorbent substrates the surfaces may be dampened slightly. Cracks should be opened up before application.

COMPOSITION AND APPEARANCE Plaster-based powder filler, special cements, calcium carbonate, resin, cellulose fibre and various admixtures. The compound obtained is white in colour. TECHNICAL CHARACTERISTICS • Setting time : 30 to 40 minutes • Hardening time : 1 to 2 hours. • Second coating : after 3 hours • Adherence : complies with NFT 30 608 SUITABLE SURFACES All types of interior surfaces complies with DTU 59.1 : plaster, plasterboard, plaster blocks, concrete, cement coating, breeze blocks, cellular concrete, bricks, ceramic, old paintwork, old painted fibreglass, floor tiles, wall tiles, etc. COVERINGS After the filler has completely dried, it can be covered using all types of paints, plaster-based coatings, paste coatings, wallpaper paste. PREPARATION OF SURFACES Surfaces must comply with standard DTU 59.1 and be clean, dry and free from dust and any trace of separating agent. Correctly open up, bevel and dust off the cracks.

TECHNICAL DEFINITION Ready mixed filler for interior and exterior finishing work on walls and ceilings OSCAR is a water based filler giving a finish identical to oil based products. COMPOSITION AND APPEARANCE Resin emulsion containing calcium carbonate, rheological agent and various additives. The resulting paste is white. ACCEPTED SUBSTRATES Interior walls and ceilings • Plasterboard • Old paint • Plaster blocks • Primers Outside walls • Smooth concrete • Fine floated cement SUITABLE SURFACES • Wallpaper • Paint • Wall coverings • Thick plastic covering (RPE) TECHNICAL CHARACTERISTICS • Paste density : 1.9 • Particle size : very fine • pH : 7 APPLICATION Application is manual using a float or a painter’s knife. The maximum thickness will be 1 mm per coat. Smooth and sand if necessary before OSCAR has entirely set. Clean tools with water.

TECHNICAL DEFINITION Levelling filler for vertical substrates and for use on ceilings for poured concrete or pre-cast slabs. Ideal for the preparation of pre-cast slabs, formwork concrete and for the renovation of textured finishes or fibreglass with a paint finish. TECHNICAL CHARACTERISTICS • Dry extract : 75% • Density : 1.86 • VOC content : less than 1g/l COMPOSITION AND APPEARANCE Water, calcium carbonate, dispersant, bactericide, fungicide, cellulosic fibres, polyacrylates, clays, acrylic dispersant. AMOUNT REQUIRED From 2 to 4 kg for the first coat. From 1.5 to 2 kg for the second coat. APPLICATION SEMIN AIRLESS EXTREM filler is sprayed using the Airless pump or rotor machine/Flat spray stator in 2 coats. The first coat must be levelled using a 60 cm blade or levelled with a straight edge. After drying, the second coat must be smoothed using a blade.

Hema NUTRI is dedicated to the particulated and non-particulated sauce and dressings market. It benefits from Hema’s proven expertise built up over several years, in the area of filling complex products for large international groups. It is available in Monobloc configuration with capper or thermosealer. NUTRI filler can also be synchronised to a neck trimmer or a rinser. Combi configuration associates blowing, filling and capping for PET bottles.

The CANFL filler is flexible, precise and perfectly adapted to the constraints of filling with complex products. Its unmatched robustness has proved itself over several years with major players in the canning industry. We are using volumetric filling with pistons which are mechanically controlled by synchronised camshaft The CANFL filler is characterised by the high-level regularity and precision that are guaranteed by the mechanically-controlled cams (repetitive motion).

Hema QCARE is dedicated to the particulated and non-particulated Home and Personal Care market. It benefits from Hema’s proven expertise built up over several years, in the area of filling complex products for large international groups. QCARE is available in Monobloc configuration with capper or Combi associating blowing, filling and capping for PET bottles.

Mechanically designed, the VOLUF filler is a reliable machine that has proved itself over many years. It is flexible and guarantees easy maintenance and respect of the products to be filled. The VOLUF is available in Stand Alone or Monobloc configuration with a capper or a thermosealer. VOLUF can be also associated with a neck trimmer or a rinser.

The ACCES filler series is dedicated to the edible oil market and has benefitted from Hema’s solid experience gained over several years of working for major International groups in the area of filling solutions for edible oil. ACCES is available in Monobloc configuration with capper or Combi associating blowing, filling and capping for PET bottles. We offer two filling technologies for edible oil : Weight – Mass Flow

The Filling method is carefully chosen to match the intrinsic characteristics of your dairy product: its type (e.g. liquid, thick, with or without particulates), what needs to be protected (flavour, vitamins, colour, etc.), its shelf-life (short or long), its sensitivity to external elements (temperature, oxygen). It is a complex equation between relative acidity (pH), the presence of nutrients, presence of O2, sugar content, preserving agents, artificial colourings, stabilisers, which all have an impact on the conservation and bacteriological quality of your dairy product. Our deep understanding of our customers’ dairy product specifications relating to filling has led us to put in place 4 environmental filling families. They mainly depend on the dairy product (weak or high level of acidity), the distribution circuit (cold chain or room temperature) and the expected shelf life of the product.

Material, version: 1. Sealing cap red Polyamide 66 thermoplastic. 2. Filler sieve black Polypropylene thermoplastic. 3 Flange electro zinc-plated steel. 4. Fastening screws electro zinc-plated steel. 5 Flange seal cork. 6. Chain brass.

Material: Aluminium. Version: Bright. Flat seal asbestos-free. On request: Cap marked OIL. Drawing reference: 1) flat seal

Housing fibreglass reinforced thermoplastic polyamide. Sight glass thermoplastic polyamide. O-ring and flat seal NBR. Reflector PVC. Float plastic. Screw and nut, steel. Version: Housing black. Sight glass crystal clear, high mechanical stability, non-ageing. Reflector white. Float red, with magnetic element. Screw and nut electro zinc-plated. Note: The oil level gauge not only enables the oil level to be viewed but also recorded using a REED switch. In addition, the oil level gauges can also emit an electric signal if the temperature of the liquid inside the container reaches the threshold of 70 °C. As soon as the float element approaches the selected minimum value after the circuit has been closed, the system emits an electric signal. The sensor is located on the housing and its height can be adjusted in line with the control requirements for the oil level. The minimum level is ca. 35 mm from the centre of the lower fastening screw.

Housing steel. Viewing glass thermoplastic polyamide. O-ring and flat seal rubber (NBR). Reflector aluminium. Screw and hex nut steel. Version: Housing painted black. Transparent viewing glass, high mechanical stability, non-ageing, temperature resistant with oil up to 100 °C, with water up to 70 °C. Reflector painted white, markings and scale black. Screw and hexagon nut, electro zinc-plated. Note: The oil level gauges can either be fastened as shown in the illustration or directly in the threaded hole. Centre distance for the fastening holes = L1 ±0.5. The oil level gauges are suitable for tanks operating without pressure. Maximum operating temperature: 100 °C.

Our vegetal fillers are composed of either olive stone flour or walnut shell flour. They are intended for the following industries: Fillers for glues: phenolics, melamine Fillers for solid explosives (public works) Fillers for bakelite/melamine-molding powder Insulation for wood-fired oven (Dusting flour to be used between something to bake and oven) Herbalism Brick alveolation and refractory materials Insulation for small foundry molds Additives for dosing vitamins in animal feed Petroleum industry: drilling mud Our product is sold in a 25kg bag or 1-ton big bag. Below is our list of products by grain size and average density: Insulation: from 0.10 to 0.315mm - from 550 to 650gr/L 100/200: from 0.10 to 0.20mm - from 470 to 570gr/L CN250: from 0 to 0.315mm - from 520 to 640gr/L CN200: from 0 to 0.20mm - from 520 to 640gr/L CN180: from 0 to 0.18mm - from 480 to 580gr/L CN100: from 0 to 0.10mm - from 450 to 520gr/L

Lebronze alloys Group was born from the integration of different companies specializing in copper alloys, copper, nickel alloys, aluminium alloys, specialty steels, stainless steels, titanium and nickel superalloys. Thanks to a multidisciplinary know-how, the Group provides innovative solutions to all major industries such as Aerospace, Oil & Gas, Power, Railway but also in sectors manufacturing smaller equipment and products. Our 16 production facilities and 1,400 employees manage a unique range of metal processing technologies: continuous and semi-continuous casting, sand casting, die precision chill casting (manual, mechanized and automated), centrifugal casting, extrusion, ring rolling, hot and cold rolling, drawing, open-die forging, hot stamping, closed-die forging, cold forming, machining, non-destructive testing, etc. The Group’s commitment is to find appropriate and optimized solutions for every sector’s requirements.